On Wed, Jun 10, 2009 at 11:33:14PM +0200, Moralejo, Alfredo wrote: > Anyone is successfully using it?
What path checker are you using? I've heard that certain path checkers cause problems, but I honestly don't know enough about dm-multipath to understand the reason for this. I have successfully used it with RDAC. Ryan > I'm testing it with a clariion storage frame on RHEL 5.3, and as soon as I > enable scsi_reserve, multipath starts failing and a path goes good and bad in > a loop and scsi fencing fails sometimes, should I configure in a specific way > multipath.conf?: > > Jun 10 23:31:58 rmamseslab07 multipathd: mpath0: remaining active paths: 3 > Jun 10 23:32:00 rmamseslab07 kernel: sd 1:0:0:1: reservation conflict > Jun 10 23:32:00 rmamseslab07 kernel: sd 1:0:0:1: SCSI error: return code = > 0x00000018 > Jun 10 23:32:00 rmamseslab07 kernel: end_request: I/O error, dev sdm, sector > 79 > Jun 10 23:32:00 rmamseslab07 kernel: device-mapper: multipath: Failing path > 8:192. > Jun 10 23:32:00 rmamseslab07 multipathd: 8:192: mark as failed > Jun 10 23:32:00 rmamseslab07 multipathd: mpathquorum: remaining active paths: > 3 > Jun 10 23:32:00 rmamseslab07 multipathd: dm-10: add map (uevent) > Jun 10 23:32:00 rmamseslab07 multipathd: dm-10: devmap already registered > Jun 10 23:32:00 rmamseslab07 multipathd: sdm: emc_clariion_checker: Path > healthy > Jun 10 23:32:00 rmamseslab07 multipathd: 8:192: reinstated > Jun 10 23:32:00 rmamseslab07 multipathd: mpathquorum: remaining active paths: > 4 > Jun 10 23:32:00 rmamseslab07 multipathd: dm-10: add map (uevent) > Jun 10 23:32:00 rmamseslab07 multipathd: dm-10: devmap already registered > Jun 10 23:32:02 rmamseslab07 multipathd: sdl: emc_clariion_checker: Path > healthy > Jun 10 23:32:02 rmamseslab07 multipathd: 8:176: reinstated > Jun 10 23:32:02 rmamseslab07 multipathd: mpath0: remaining active paths: 4 > Jun 10 23:32:02 rmamseslab07 multipathd: dm-9: add map (uevent) > Jun 10 23:32:02 rmamseslab07 multipathd: dm-9: devmap already registered > Jun 10 23:32:03 rmamseslab07 kernel: sd 1:0:0:0: reservation conflict > Jun 10 23:32:03 rmamseslab07 kernel: sd 1:0:0:0: SCSI error: return code = > 0x00000018 > Jun 10 23:32:03 rmamseslab07 kernel: end_request: I/O error, dev sdl, sector > 25256 > Jun 10 23:32:03 rmamseslab07 kernel: device-mapper: multipath: Failing path > 8:176. > Jun 10 23:32:03 rmamseslab07 multipathd: dm-9: add map (uevent) > Jun 10 23:32:03 rmamseslab07 multipathd: dm-9: devmap already registered > Jun 10 23:32:03 rmamseslab07 multipathd: 8:176: mark as failed > Jun 10 23:32:03 rmamseslab07 multipathd: mpath0: remaining active paths: 3 > > > > -----Original Message----- > From: linux-cluster-boun...@redhat.com > [mailto:linux-cluster-boun...@redhat.com] On Behalf Of Ryan O'Hara > Sent: Wednesday, June 10, 2009 9:18 PM > To: linux clustering > Subject: Re: [Linux-cluster] fence_scsi support in multipath env in RHEL5.3 > > On Wed, Jun 10, 2009 at 02:11:21PM +0530, Rajeev P wrote: > > I wanted to know if fence_scsi is supported in a multipath environment for > > RHEL5.3 release. > > Yes, it is supported. > > > In earlier releases of RHEL5 fence_scsi was not supported in a multipath > > environment for RHEL5.3 release. If I am not wrong, this was because the > > DM-MPIO driver forwarded the registration/unregistration commands on only on > > one of the physical paths of a LUN. Ideally it should have passed the > > commands on all physical paths. > > > > For RHEL5.3, is this issue resolved so that I can fence_scsi in multipath > > environment. > > > > Thanks in advance. > > > > Rajeev > > > -- > > Linux-cluster mailing list > > Linux-cluster@redhat.com > > https://www.redhat.com/mailman/listinfo/linux-cluster > > -- > Linux-cluster mailing list > Linux-cluster@redhat.com > https://www.redhat.com/mailman/listinfo/linux-cluster > > -- > Linux-cluster mailing list > Linux-cluster@redhat.com > https://www.redhat.com/mailman/listinfo/linux-cluster -- Linux-cluster mailing list Linux-cluster@redhat.com https://www.redhat.com/mailman/listinfo/linux-cluster