Linux-Development-Sys Digest #809, Volume #6 Thu, 10 Jun 99 06:14:31 EDT
Contents:
Re: Images ("Lenny grosso")
Red Hat 6.0 not fscking the root partition! (Ronald Cole)
Re: select() vs. poll() ("Bill Zimmerly")
Re: new kernel: LILO "kernel too big" error (Martin A. Boegelund)
----------------------------------------------------------------------------
From: "Lenny grosso" <[EMAIL PROTECTED]>
Subject: Re: Images
Date: Wed, 9 Jun 1999 22:57:28 -0500
Can anybody tell me where this great howto is?
thanks
Lenny
Clint Byrum wrote in message <7jmvnv$[EMAIL PROTECTED]>...
>There is a great Bootdisk-HOWTO that will tell you how to create bootdisks.
>It helped me to understand a lot of the stuff that goes on a system bootup.
>
>Lenny grosso wrote in message <7jkah0$pme$[EMAIL PROTECTED]>...
>>Can anybody tell me about creating boot images for a floppy disk?
>>
>>Thanks
>>Lenny Grosso
>>
>>
>>
>
>
------------------------------
From: Ronald Cole <[EMAIL PROTECTED]>
Subject: Red Hat 6.0 not fscking the root partition!
Date: 09 Jun 1999 14:15:58 -0700
I'm a new convert to Red Hat (from Slackware). I've performed a
"Server" install of "official" Red Hat 6.0 and noticed that the root
partition check is aborting and therefore the root partition never
gets checked. I rebooted several dozen times while configuring the
system. I've tried Red Hat's "on-line support" but it is horribly
broken and Red Hat's support manager admits as much but doesn't offer
any useful suggestions to resolve the issue (all email gets promptly
ignored, but that is another problem)...
My problem is that, in /etc/rc.d/rc.sysinit, the root partition is
checked with the command "fsck -T -a /" which causes the WARNING in
the attached logfile.:
/dev/sda8 is mounted.
WARNING!!! Running e2fsck on a mounted filesystem may cause
SEVERE filesystem damage.
check aborted.
You'll note that rc.sysinit reports:
Checking root filesystem succeeded
immediately after the check was aborted! This is a most heinous lie!!
You'll also note that when enough reboots caused a forced filesystem
check, that the root partition has indeed gone unchecked since the OS
was installed:
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended.
Slackware 3.4 used -a with fsck, but used e2fsck-1.10, while Red Hat
6.0 uses e2fsck-1.14. Did something change between 1.10 and 1.14 or
did fsck just get stupid? How should I fix the fsck command in
/etc/rc.d/rc.sysinit?
Here are the /var/log/messages and /var/log/dmesg:
===============================================================================
May 18 23:37:57 genkan rc.sysinit: Loading default keymap succeeded
May 18 23:37:58 genkan rc.sysinit: Setting default font succeeded
May 18 23:37:58 genkan swapon: swapon: warning: /dev/sda9 has insecure permissions
0660, 0600 suggested
May 18 23:37:58 genkan rc.sysinit: Activating swap partitions succeeded
May 18 23:37:58 genkan rc.sysinit: Setting hostname genkan.forte-intl.com succeeded
May 18 23:37:58 genkan fsck: /dev/sda8 is mounted.
May 18 23:37:58 genkan fsck: ^G^G^G^GWARNING!!! Running e2fsck on a mounted
filesystem may cause
May 18 23:37:58 genkan fsck: SEVERE filesystem damage.^G^G^G
May 18 23:37:58 genkan fsck: check aborted.
May 18 23:37:58 genkan rc.sysinit: Checking root filesystem succeeded
May 18 23:37:59 genkan rc.sysinit: Remounting root filesystem in read-write mode
succeeded
May 18 23:38:14 genkan rc.sysinit: Finding module dependencies succeeded
May 18 23:38:15 genkan fsck: /dev/sda1 has reached maximal mount count, check forced.
May 18 23:38:15 genkan fsck: /dev/sda1: 24/4160 files (0.0% non-contiguous),
3232/16385 blocks
May 18 23:38:15 genkan fsck: /dev/sda6 has reached maximal mount count, check forced.
May 18 23:38:27 genkan fsck: /dev/sda6: 404/187680 files (0.5% non-contiguous),
27574/749766 blocks
May 18 23:38:28 genkan fsck: /dev/sda5 has reached maximal mount count, check forced.
May 18 23:39:22 genkan fsck: /dev/sda5: 22835/187680 files (0.5% non-contiguous),
345858/749766 blocks
May 18 23:39:23 genkan fsck: /dev/sda7 has reached maximal mount count, check forced.
May 18 23:39:27 genkan fsck: /dev/sda7: 197/66000 files (9.6% non-contiguous),
15484/263748 blocks
May 18 23:39:28 genkan rc.sysinit: Checking filesystems succeeded
May 18 16:39:30 genkan rc.sysinit: Mounting local filesystems succeeded
May 18 16:39:30 genkan rc.sysinit: Turning on user and group quotas for local
filesystems succeeded
May 18 23:39:32 genkan date: Tue May 18 16:39:32 PDT 1999
May 18 16:39:32 genkan rc.sysinit: Setting clock (utc): Tue May 18 16:39:32 PDT 1999
succeeded
May 18 16:39:32 genkan rc.sysinit: Enabling swap space succeeded
May 18 16:39:32 genkan init: Entering runlevel: 5
May 18 16:39:34 genkan apmd[100]: Version 3.0beta4 (APM BIOS 1.1, Linux driver 1.9)
May 18 16:39:34 genkan apmd: apmd startup succeeded
May 18 16:39:35 genkan network: Enabling IPv4 packet forwarding succeeded
May 18 16:39:39 genkan network: Bringing up interface lo succeeded
May 18 16:39:42 genkan network: Bringing up interface eth0 succeeded
May 18 16:39:43 genkan network: Bringing up interface ppp0 succeeded
May 18 16:39:44 genkan ifup-ppp: pppd started for ppp0 on /dev/ttyS0 at 115200
May 18 16:39:45 genkan pppd[271]: pppd 2.3.7 started by root, uid 0
May 18 16:39:45 genkan portmap: portmap startup succeeded
May 18 16:39:46 genkan netfs: Mounting other filesystems succeeded
May 18 16:39:46 genkan random: Initializing random number generator succeeded
May 18 16:39:46 genkan chat[317]: abort on (BUSY)
May 18 16:39:46 genkan chat[317]: abort on (NO CARRIER)
May 18 16:39:46 genkan chat[317]: abort on (Invalid Login)
May 18 16:39:46 genkan chat[317]: send (ATZ^M)
May 18 16:39:46 genkan chat[317]: ATZ^M^M
May 18 16:39:46 genkan chat[317]: -- got it
May 18 16:39:47 genkan chat[317]: expect (CONNECT) <150>May 18 16:39:47 chat[317]: ^M
May 18 16:39:50 genkan kernel: Loaded 7132 symbols from /boot/System.map-2.2.5-15.
May 18 16:39:50 genkan atd: atd startup succeeded
May 18 16:39:50 genkan kernel: Symbols match kernel version 2.2.5.
May 18 16:39:50 genkan kernel: Loaded 24 symbols from 4 modules.
May 18 16:39:50 genkan kernel: Linux version 2.2.5-15 ([EMAIL PROTECTED])
(gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Mon Apr 19 21:39:28
EDT 1999
May 18 16:39:50 genkan kernel: Console: colour VGA+ 80x25
May 18 16:39:50 genkan kernel: Calibrating delay loop... 49.87 BogoMIPS
May 18 16:39:50 genkan kernel: Memory: 62772k/65536k available (1060k kernel code,
412k reserved, 928k data, 60k init)
May 18 16:39:50 genkan kernel: VFS: Diskquotas version dquot_6.4.0 initialized
May 18 16:39:50 genkan kernel: CPU: Intel 486 DX/4 stepping 03
May 18 16:39:50 genkan kernel: Checking 386/387 coupling... OK, FPU using exception 16
error reporting.
May 18 16:39:50 genkan kernel: Checking 'hlt' instruction... OK.
May 18 16:39:50 genkan kernel: Checking for popad bug... OK.
May 18 16:39:50 genkan kernel: POSIX conformance testing by UNIFIX
May 18 16:39:50 genkan kernel: PCI: PCI BIOS revision 2.00 entry at 0xfc770
May 18 16:39:50 genkan kernel: PCI: Using configuration type 2
May 18 16:39:50 genkan kernel: PCI: Probing PCI hardware
May 18 16:39:50 genkan kernel: Linux NET4.0 for Linux 2.2
May 18 16:39:50 genkan kernel: Based upon Swansea University Computer Society NET3.039
May 18 16:39:50 genkan kernel: NET4: Unix domain sockets 1.0 for Linux NET4.0.
May 18 16:39:50 genkan kernel: NET4: Linux TCP/IP 1.0 for NET4.0
May 18 16:39:51 genkan kernel: IP Protocols: ICMP, UDP, TCP, IGMP
May 18 16:39:51 genkan kernel: Initializing RT netlink socket
May 18 16:39:51 genkan kernel: Starting kswapd v 1.5
May 18 16:39:51 genkan kernel: Detected PS/2 Mouse Port.
May 18 16:39:51 genkan kernel: Serial driver version 4.27 with MANY_PORTS MULTIPORT
SHARE_IRQ enabled
May 18 16:39:51 genkan kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
May 18 16:39:51 genkan kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
May 18 16:39:51 genkan kernel: pty: 256 Unix98 ptys configured
May 18 16:39:51 genkan kernel: apm: BIOS version 1.1 Flags 0x03 (Driver version 1.9)
May 18 16:39:51 genkan kernel: Real Time Clock Driver v1.09
May 18 16:39:51 genkan kernel: RAM disk driver initialized: 16 RAM disks of 4096K
size
May 18 16:39:51 genkan kernel: Floppy drive(s): fd0 is 1.44M
May 18 16:39:51 genkan kernel: FDC 0 is a National Semiconductor PC87306
May 18 16:39:51 genkan kernel: md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
May 18 16:39:51 genkan kernel: raid5: measuring checksumming speed
May 18 16:39:51 genkan kernel: 8regs : 64.008 MB/sec
May 18 16:39:51 genkan kernel: 32regs : 43.053 MB/sec
May 18 16:39:51 genkan kernel: using fastest function: 8regs (64.008 MB/sec)
May 18 16:39:51 genkan kernel: scsi : 0 hosts.
May 18 16:39:51 genkan kernel: scsi : detected total.
May 18 16:39:51 genkan kernel: md.c: sizeof(mdp_super_t) = 4096
May 18 16:39:51 genkan kernel: Partition check:
May 18 16:39:51 genkan kernel: RAMDISK: Compressed image found at block 0
May 18 16:39:51 genkan kernel: autodetecting RAID arrays
May 18 16:39:51 genkan kernel: autorun ...
May 18 16:39:51 genkan kernel: ... autorun DONE.
May 18 16:39:51 genkan kernel: VFS: Mounted root (ext2 filesystem).
May 18 16:39:51 genkan kernel: ncr53c8xx: at PCI bus 0, device 1, function 0
May 18 16:39:51 genkan kernel: ncr53c8xx: 53c810 detected
May 18 16:39:51 genkan kernel: ncr53c810-0: rev=0x02, base=0xfbf3f000, io_port=0xe800,
irq=9
May 18 16:39:51 genkan kernel: ncr53c810-0: ID 7, Fast-10, Parity Checking
May 18 16:39:51 genkan kernel: ncr53c810-0: restart (scsi reset).
May 18 16:39:51 genkan kernel: scsi0 : ncr53c8xx - revision 3.1h
May 18 16:39:51 genkan kernel: scsi : 1 host.
May 18 16:39:51 genkan kernel: Vendor: IBM Model: DORS-32160 !# Rev: WA1A
May 18 16:39:51 genkan kernel: Type: Direct-Access ANSI SCSI
revision: 02
May 18 16:39:51 genkan kernel: Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
May 18 16:39:51 genkan kernel: Vendor: CyberDrv Model: SCSI CD-ROM 120S Rev: 1.30
May 18 16:39:51 genkan kernel: Type: CD-ROM ANSI SCSI
revision: 02
May 18 16:39:51 genkan kernel: Detected scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun
0
May 18 16:39:51 genkan kernel: scsi0 : channel 0 target 2 lun 1 request sense failed,
performing reset.
May 18 16:39:51 genkan kernel: SCSI bus is being reset for host 0 channel 0.
May 18 16:39:51 genkan kernel: ncr53c8xx_reset: pid=12 reset_flags=1 serial_number=0
serial_number_at_timeout=0
May 18 16:39:51 genkan kernel: scsi0: device driver called scsi_done() for a
syncronous reset.
May 18 16:39:51 genkan kernel: ncr53c810-0: restart (scsi reset).
May 18 16:39:51 genkan kernel: ncr53c810-0-<0,0>: tagged command queue depth set to 8
May 18 16:39:51 genkan kernel: ncr53c810-0-<2,*>: device did not report SYNC.
May 18 16:39:51 genkan kernel: sr0: scsi3-mmc drive: 12x/12x xa/form2 cdda tray
May 18 16:39:51 genkan kernel: Uniform CDROM driver Revision: 2.54
May 18 16:39:51 genkan kernel: ncr53c810-0-<0,*>: FAST-10 SCSI 10.0 MB/s (100 ns,
offset 8)
May 18 16:39:51 genkan kernel: SCSI device sda: hdwr sector= 512 bytes. Sectors=
4226725 [2063 MB] [2.1 GB]
May 18 16:39:51 genkan kernel: sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 >
May 18 16:39:51 genkan kernel: autodetecting RAID arrays
May 18 16:39:51 genkan kernel: autorun ...
May 18 16:39:51 genkan kernel: ... autorun DONE.
May 18 16:39:51 genkan kernel: EXT2-fs warning: maximal mount count reached, running
e2fsck is recommended
May 18 16:39:51 genkan kernel: VFS: Mounted root (ext2 filesystem).
May 18 16:39:51 genkan kernel: change_root: old root has d_count=1
May 18 16:39:51 genkan kernel: Trying to unmount old root ... okay
May 18 16:39:51 genkan kernel: Freeing unused kernel memory: 60k freed
May 18 16:39:51 genkan kernel: Adding Swap: 66428k swap-space (priority -1)
May 18 16:39:51 genkan kernel: tulip.c:v0.89H 5/23/98 [EMAIL PROTECTED]
May 18 16:39:51 genkan kernel: eth0: Digital DS21140 Tulip at 0xe400, 00 c0 f0 31 8e
bf, IRQ 11.
May 18 16:39:51 genkan kernel: eth0: EEPROM default media type Autosense.
May 18 16:39:51 genkan kernel: eth0: Index #0 - Media MII (#11) described by a 21140
MII PHY (1) block.
May 18 16:39:51 genkan kernel: eth0: MII transceiver found at MDIO address 1, config
3000 status 782d.
May 18 16:39:51 genkan kernel: eth1: Digital DS21140 Tulip at 0xe000, 00 c0 f0 17 13
4f, IRQ 10.
May 18 16:39:51 genkan kernel: eth1: EEPROM default media type Autosense.
May 18 16:39:51 genkan kernel: eth1: Index #0 - Media MII (#11) described by a 21140
MII PHY (1) block.
May 18 16:39:51 genkan kernel: eth1: MII transceiver found at MDIO address 1, config
3000 status 7809.
May 18 16:39:51 genkan kernel: CSLIP: code copyright 1989 Regents of the University of
California
May 18 16:39:51 genkan kernel: PPP: version 2.3.3 (demand dialling)
May 18 16:39:51 genkan kernel: PPP line discipline registered.
May 18 16:39:51 genkan kernel: registered device ppp0
May 18 16:39:52 genkan crond: crond startup succeeded
May 18 16:39:52 genkan rc: Starting pcmcia succeeded
May 18 16:39:53 genkan inet: inetd startup succeeded
May 18 16:39:54 genkan named[403]: starting. named 8.2 Wed Mar 31 10:57:12 EST 1999
^[EMAIL PROTECTED]:/usr/src/bs/BUILD/bind-8.2/src/bin/named
May 18 16:39:54 genkan named[403]: cache zone "" (IN) loaded (serial 0)
May 18 16:39:54 genkan named[403]: Zone "forte-intl.com" (file zone/forte-intl.com):
No default TTL set using SOA minimum instead
May 18 16:39:54 genkan named[403]: master zone "forte-intl.com" (IN) loaded (serial
1999051801)
May 18 16:39:54 genkan named[403]: Zone "0.0.127.in-addr.arpa" (file zone/127.0.0): No
default TTL set using SOA minimum instead
May 18 16:39:54 genkan named[403]: master zone "0.0.127.in-addr.arpa" (IN) loaded
(serial 1999051703)
May 18 16:39:54 genkan named[403]: Zone "1.168.192.in-addr.arpa" (file
zone/192.168.1): No default TTL set using SOA minimum instead
May 18 16:39:54 genkan named[403]: master zone "1.168.192.in-addr.arpa" (IN) loaded
(serial 1999051702)
May 18 16:39:54 genkan named[403]: listening on [127.0.0.1].53 (lo)
May 18 16:39:54 genkan named[403]: listening on [192.168.1.1].53 (eth0)
May 18 16:39:54 genkan named[403]: Forwarding source address is [0.0.0.0].1024
May 18 16:39:54 genkan named: named startup succeeded
May 18 16:39:55 genkan named[404]: Ready to answer queries.
May 18 16:39:55 genkan named[404]: sysquery: sendto([192.33.4.12].53): Network is
unreachable
May 18 16:39:55 genkan lpd: lpd startup succeeded
May 18 16:39:56 genkan nfs: Starting NFS services: succeeded
May 18 16:39:57 genkan nfs: rpc.statd startup succeeded
May 18 16:39:58 genkan nfs: rpc.rquotad startup succeeded
May 18 16:39:58 genkan nfs: rpc.mountd startup succeeded
May 18 16:40:00 genkan kernel: Installing knfsd (copyright (C) 1996
[EMAIL PROTECTED]).
May 18 16:40:00 genkan nfs: rpc.nfsd startup succeeded
May 18 16:40:00 genkan keytable: Loading keymap:
May 18 16:40:00 genkan keytable: Loading /usr/lib/kbd/keymaps/i386/qwerty/us.kmap.gz
May 18 16:40:01 genkan keytable: Loading system font:
May 18 16:40:01 genkan rc: Starting keytable succeeded
May 18 16:40:03 genkan sendmail: sendmail startup succeeded
May 18 16:40:04 genkan gpm: gpm startup succeeded
May 18 16:40:06 genkan httpd: httpd startup succeeded
May 18 16:40:08 genkan PAM_pwdb[569]: (su) session opened for user xfs by (uid=0)
May 18 16:40:08 genkan PAM_pwdb[569]: (su) session closed for user xfs
May 18 16:40:08 genkan xfs: xfs startup succeeded
May 18 16:40:09 genkan PAM_pwdb[578]: (su) session opened for user news by (uid=0)
May 18 16:40:13 genkan actived[627]: started
May 18 16:40:13 genkan innd: SERVER descriptors 1024
May 18 16:40:13 genkan innd: SERVER outgoing 1011
May 18 16:40:13 genkan innd: SERVER ccsetup control:14
May 18 16:40:13 genkan innd: SERVER lcsetup localconn:16
May 18 16:40:13 genkan innd: SERVER rcsetup remconn:5
May 18 16:40:13 genkan innd: SERVER bad_newsfeeds no feeding sites
May 18 16:40:13 genkan PAM_pwdb[578]: (su) session closed for user news
May 18 16:40:13 genkan linuxconf: Linuxconf final setup
May 18 16:40:13 genkan innd: SERVER perl filtering enabled
May 18 16:40:13 genkan innd: SERVER starting
May 18 16:40:15 genkan rc: Starting linuxconf succeeded
May 18 16:40:16 genkan rc: Starting local succeeded
May 18 16:40:19 genkan chat[317]: CONNECT
May 18 16:40:19 genkan chat[317]: -- got it
May 18 16:40:19 genkan chat[317]: send (^M)
May 18 16:40:19 genkan chat[317]: timeout set to 5 seconds
May 18 16:40:19 genkan pppd[271]: Using interface ppp0
May 18 16:40:19 genkan pppd[271]: Connect: ppp0 <--> /dev/ttyS0
May 18 16:40:20 genkan pppd[271]: Remote message: ^D^EM-t^B^F
May 18 16:40:20 genkan kernel: PPP BSD Compression module registered
May 18 16:40:21 genkan kernel: PPP Deflate Compression module registered
May 18 16:40:21 genkan pppd[271]: Unsupported protocol (0x8031) received
May 18 16:40:21 genkan pppd[271]: local IP address 207.141.203.99
May 18 16:40:21 genkan pppd[271]: remote IP address 207.141.203.150
===============================================================================
Linux version 2.2.5-15 ([EMAIL PROTECTED]) (gcc version egcs-2.91.66
19990314/Linux (egcs-1.1.2 release)) #1 Mon Apr 19 21:39:28 EDT 1999
Console: colour VGA+ 80x25
Calibrating delay loop... 49.87 BogoMIPS
Memory: 62772k/65536k available (1060k kernel code, 412k reserved, 928k data, 60k init)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: Intel 486 DX/4 stepping 03
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.00 entry at 0xfc770
PCI: Using configuration type 2
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.1 Flags 0x03 (Driver version 1.9)
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
8regs : 64.008 MB/sec
32regs : 43.053 MB/sec
using fastest function: 8regs (64.008 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
RAMDISK: Compressed image found at block 0
autodetecting RAID arrays
autorun ...
.... autorun DONE.
VFS: Mounted root (ext2 filesystem).
ncr53c8xx: at PCI bus 0, device 1, function 0
ncr53c8xx: 53c810 detected
ncr53c810-0: rev=0x02, base=0xfbf3f000, io_port=0xe800, irq=9
ncr53c810-0: ID 7, Fast-10, Parity Checking
ncr53c810-0: restart (scsi reset).
scsi0 : ncr53c8xx - revision 3.1h
scsi : 1 host.
Vendor: IBM Model: DORS-32160 !# Rev: WA1A
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: CyberDrv Model: SCSI CD-ROM 120S Rev: 1.30
Type: CD-ROM ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
scsi0 : channel 0 target 2 lun 1 request sense failed, performing reset.
SCSI bus is being reset for host 0 channel 0.
ncr53c8xx_reset: pid=12 reset_flags=1 serial_number=0 serial_number_at_timeout=0
scsi0: device driver called scsi_done() for a syncronous reset.
ncr53c810-0: restart (scsi reset).
ncr53c810-0-<0,0>: tagged command queue depth set to 8
ncr53c810-0-<2,*>: device did not report SYNC.
sr0: scsi3-mmc drive: 12x/12x xa/form2 cdda tray
Uniform CDROM driver Revision: 2.54
ncr53c810-0-<0,*>: FAST-10 SCSI 10.0 MB/s (100 ns, offset 8)
SCSI device sda: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB]
sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 >
autodetecting RAID arrays
autorun ...
.... autorun DONE.
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
change_root: old root has d_count=1
Trying to unmount old root ... okay
Freeing unused kernel memory: 60k freed
Adding Swap: 66428k swap-space (priority -1)
===============================================================================
--
Forte International, P.O. Box 1412, Ridgecrest, CA 93556-1412
Ronald Cole <[EMAIL PROTECTED]> Phone: (760) 499-9142
President, CEO Fax: (760) 499-9152
My PGP fingerprint: 15 6E C7 91 5F AF 17 C4 24 93 CB 6B EB 38 B5 E5
------------------------------
From: "Bill Zimmerly" <[EMAIL PROTECTED]>
Subject: Re: select() vs. poll()
Date: Wed, 9 Jun 1999 12:49:28 -0500
Bjorn,
Do you mind elaborating a bit on the "synchronization bug" that you wrote
about here? Is there a website that you can direct me to that covers this?
I'm asking this because I am seeing what appears to be a socket problem in
Win32, but am not sure that it's the same thing as the bug you wrote about.
Many thanks for pointing this out!
- Bill
Bj�rn Reese <[EMAIL PROTECTED]> wrote in message
news:[EMAIL PROTECTED]...
> "G. Sumner Hayes" wrote:
>
> > Caveat: On Win32 the semantics are different. select()ing on
> > things other than network sockets doesn't work, in general.
> > WaitForMultipleObjects* and WSAAsyncSelect are preferred.
>
> Yes, along with the other Win32 related problems, such as select()
> only being able to handle 64 sockets, and the synchronization bug
> which has to be worked around with a Sleep().
------------------------------
From: Martin A. Boegelund <[EMAIL PROTECTED]>
Crossposted-To: comp.os.linux.setup,comp.os.linux.help
Subject: Re: new kernel: LILO "kernel too big" error
Date: Thu, 10 Jun 1999 08:47:40 GMT
In article <kwf73.292$[EMAIL PROTECTED]>,
"steve davidson" <[EMAIL PROTECTED]> wrote:
> I'm finding it hard to believe that 426KB is actually too big - I get
the
> feeling this is a bogus message and something else is going on here.
>
Me too. I had a kernel-source (2.2.9) and a .config file that worked
with RH5.2, but using those with RH6.0 gave me "kernel too big".
Also, using "make bzImage" might not help, since I later on get
problems with compiling my modules; I get errors from modules I
_didn't_ select... Well they are selected, but greyed out by an earlier
de-selection so they shouldn't have any influence on module
compilation, or what?
Very strange...
Any comments, ideas, help???
[deletia]
--
==================
Mr Sparkle - Aka Martin A. Boegelund
Sent via Deja.com http://www.deja.com/
Share what you know. Learn what you don't.
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list (and comp.os.linux.development.system) via:
Internet: [EMAIL PROTECTED]
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Development-System Digest
******************************
