i have that problem,
and have the versio /diald-0.99.1-2.i386.rpm and
RH 6.0
with kernel 2.2.15pre19
but with line isdn connected to COM 1.
i wear PAP authencation.
i need help, please
regards.
leo
On Tue, 25 Apr 2000, Ale wrote:
> Hello Folks!
>
> I guess if anyone of you can give me a hand.
> I got in serious troubles running diald. Here are my config files. I made a
> script to manually connect to the Internet (it works fine!) I cannot use
> with diald.
>
> frankie:/home/ale/diald# less /usr/bin/goppp
> /usr/sbin/pppd connect ' /usr/sbin/chat -v -t60 -f /etc/I_conn.chat' user
> aleque
>
> (password defined in the ppp's secret file)
> The script...
>
> frankie:/home/ale/diald# less /etc/I_conn.chat
> "" ATZ OK ATB40&J0 OK ATD0230900000 CONNECT ""
>
> Here's my diald config:
>
> frankie:/home/ale/diald# less /etc/diald.conf
> mode ppp
> connect /etc/I_conn.chat
> device /dev/ttyS1
> speed 115200
> modem
> lock
> crtscts
> local 192.168.2.1
> remote 192.168.2.2
> dynamic
> defaultroute
>
> (192.168.2.x are DUMMY ADDRESSES)
> (question: where shall I put login info?)
>
> frankie:/home/ale/diald# route
> Kernel IP routing table
> Destination Gateway Genmask Flags Metric Ref Use Iface
> localnet * 255.255.255.0 U 0 0 0 eth0
> loopback * 255.0.0.0 U 0 0 0 lo
>
> frankie:/home/ale/diald# diald
>
> frankie:/home/ale/diald# route -n
> Kernel IP routing table
> Destination Gateway Genmask Flags Metric Ref Use Iface
> 192.168.2.2 0.0.0.0 255.255.255.255 UH 1 0 0 sl0
> 192.168.5.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
> 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
> 0.0.0.0 0.0.0.0 0.0.0.0 U 1 0 0 sl0
>
> (seems to be ok, sl0 is up)
>
> frankie:/home/ale/diald# ifconfig
>
> eth0 Link encap:Ethernet HWaddr 00:C0:DF:81:5E:05
> inet addr:192.168.5.1 Bcast:192.168.5.255 Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:2492 errors:0 dropped:0 overruns:0 frame:0
> TX packets:1200 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:100
> Interrupt:10 Base address:0x340
>
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 Mask:255.0.0.0
> UP LOOPBACK RUNNING MTU:3924 Metric:1
> RX packets:9787 errors:0 dropped:0 overruns:0 frame:0
> TX packets:9787 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
>
> sl0 Link encap:Serial Line IP
> inet addr:192.168.2.1 P-t-P:192.168.2.2 Mask:255.255.255.255
> UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:10
>
>
> In /var/adm/messages I found errors:
>
> frankie:/home/ale/diald# tail /var/adm/messages
> Apr 25 14:04:57 frankie diald[817]: start sl0: SIOCSIFMETRIC: Operation not
> supported
>
> ?!?
>
> Ok. after this any application involving the network hungs (I mean, also
> with ETH0!) waiting for diald to call (and obviously it doesn't) . :-(
>
> Config: Slack7, anything (I hope) well set.
>
> Thanks in advance!
> Ale
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-diald" in
> the body of a message to [EMAIL PROTECTED]
>
-
To unsubscribe from this list: send the line "unsubscribe linux-diald" in
the body of a message to [EMAIL PROTECTED]
