Add device tree binding support for I2C Controller in GENI based
QUP Wrapper.
Signed-off-by: Sagar Dharia <sdha...@codeaurora.org>
Signed-off-by: Karthikeyan Ramasubramanian <krama...@codeaurora.org>
---
.../devicetree/bindings/i2c/i2c-qcom-geni.txt | 35 ++++++++++++++++++++++
.../devicetree/bindings/soc/qcom/qcom,geni-se.txt | 19 ++++++++++++
2 files changed, 54 insertions(+)
create mode 100644 Documentation/devicetree/bindings/i2c/i2c-qcom-geni.txt
diff --git a/Documentation/devicetree/bindings/i2c/i2c-qcom-geni.txt
b/Documentation/devicetree/bindings/i2c/i2c-qcom-geni.txt
new file mode 100644
index 0000000..ea84be7
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-qcom-geni.txt
@@ -0,0 +1,35 @@
+Qualcomm Technologies Inc. GENI Serial Engine based I2C Controller
+
+Required properties:
+ - compatible: Should be:
+ * "qcom,i2c-geni.
+ - reg: Should contain QUP register address and length.
+ - interrupts: Should contain I2C interrupt.
+ - clock-names: Should contain "se-clk".
+ - clocks: Serial engine core clock needed by the device.
+ - pinctrl-names/pinctrl-0/1: The GPIOs assigned to this core. The names
+ should be "active" and "sleep" for the pin confuguration when core is active
+ or when entering sleep state.
+ - #address-cells: Should be <1> Address cells for i2c device address
+ - #size-cells: Should be <0> as i2c addresses have no size component
+
+Optional property:
+ - clock-frequency : Desired I2C bus clock frequency in Hz.
+ When missing default to 400000Hz.
+
+Child nodes should conform to i2c bus binding.
+
+Example:
+
+i2c0: i2c@a94000 {
+ compatible = "qcom,i2c-geni";
+ reg = <0xa94000 0x4000>;
+ interrupts = <GIC_SPI 358 0>;
+ clock-names = "se-clk";
+ clocks = <&clock_gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_1_i2c_5_active>;
+ pinctrl-1 = <&qup_1_i2c_5_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+};
diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
index 66f8a16..2ffbb3e 100644
--- a/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
+++ b/Documentation/devicetree/bindings/soc/qcom/qcom,geni-se.txt
@@ -24,6 +24,9 @@ A GENI based QUP wrapper controller node can contain 0 or
more child nodes
representing serial devices. These serial devices can be a QCOM UART, I2C
controller, spi controller, or some combination of aforementioned devices.
+See the following documentation for child node definitions:
+Documentation/devicetree/bindings/i2c/i2c-qcom-geni.txt
+
Example:
qup0: qcom,geniqup0@8c0000 {
compatible = "qcom,geni-se-qup";
@@ -31,4 +34,20 @@ Example:
clock-names = "m-ahb", "s-ahb";
clocks = <&clock_gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
<&clock_gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ i2c0: i2c@a94000 {
+ compatible = "qcom,i2c-geni";
+ reg = <0xa94000 0x4000>;
+ interrupts = <GIC_SPI 358 0>;
+ clock-names = "se-clk";
+ clocks = <&clock_gcc GCC_QUPV3_WRAP0_S5_CLK>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&qup_1_i2c_5_active>;
+ pinctrl-1 = <&qup_1_i2c_5_sleep>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
}
--
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-doc" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
