On Tue, Oct 15, 2019 at 10:20:04PM +0100, Mike Leach wrote:
> Add in detailed programmers reference for users wanting to program the
> CoreSight ETM 4.x driver using sysfs.
>
> Signed-off-by: Mike Leach <mike.le...@linaro.org>
> ---
> .../coresight/coresight-etm4x-reference.rst | 798 ++++++++++++++++++
> 1 file changed, 798 insertions(+)
> create mode 100644
> Documentation/trace/coresight/coresight-etm4x-reference.rst
>
> diff --git a/Documentation/trace/coresight/coresight-etm4x-reference.rst
> b/Documentation/trace/coresight/coresight-etm4x-reference.rst
> new file mode 100644
> index 000000000000..b64d9a9c79df
> --- /dev/null
> +++ b/Documentation/trace/coresight/coresight-etm4x-reference.rst
> @@ -0,0 +1,798 @@
> +===============================================
> +ETMv4 sysfs linux driver programming reference.
> +===============================================
> +
> + :Author: Mike Leach <mike.le...@linaro.org>
> + :Date: October 11th, 2019
> +
> +Supplement to existing ETMv4 driver documentation.
> +
> +Sysfs files and directories
> +---------------------------
> +
> +Root: ``/sys/bus/coresight/devices/etm<N>``
> +
> +
> +The following paragraphs explain the association between sysfs files and the
> +ETMv4 registers that they effect. Note the register names are given without
> +the ‘TRC’ prefix.
> +
> +----
> +
> +:File: ``mode`` (rw)
> +:Trace Registers: {CONFIGR + others}
> +:Notes:
> + Bit select trace features. See ‘mode’ section below. Bits
> + in this will cause equivalent programming of trace config and
> + other registers to enable the features requested.
> +
> +:Syntax & eg:
> + ``echo bitfield > mode``
> +
> + bitfield up to 32 bits setting trace features.
> +
> +:Example:
> + ``$> echo 0x012 > mode``
> +
> +----
> +
> +:File: ``reset`` (wo)
> +:Trace Registers: All
> +:Notes:
> + Reset all programming to trace nothing / no logic programmed.
> +
> +:Syntax:
> + ``echo 1 > reset``
> +
> +----
> +
> +:File: ``enable_source`` (wo)
> +:Trace Registers: PRGCTLR, All hardware regs.
> +:Notes:
> + - > 0 : Programs up the hardware with the current values held in the
> driver
> + and enables trace.
> +
> + - = 0 : disable trace hardware.
> +
> +:Syntax:
> + ``echo 1 > enable_source``
> +
> +----
> +
> +:File: ``cpu`` (ro)
> +:Trace Registers: None.
> +:Notes:
> + CPU ID that this ETM is attached to.
> +
> +:Example:
> + ``$> cat cpu``
> +
> + ``$> 0``
> +
> +----
> +
> +:File: ``addr_idx`` (rw)
> +:Trace Registers: None.
> +:Notes:
> + Virtual register to index address comparator and range
> + features. Set index for first of the pair in a range.
> +
> +:Syntax:
> + ``echo idx > addr_idx``
> +
> + Where idx < nr_addr_cmp x 2
> +
> +----
> +
> +:File: ``addr_range`` (rw)
> +:Trace Registers: ACVR[idx, idx+1], VIIECTLR
> +:Notes:
> + Pair of addresses for a range selected by addr_idx. Include
> + / exclude according to the optional parameter, or if omitted
> + uses the current ‘mode’ setting. Select comparator range in
> + control register. Error if index is odd value.
> +
> +:Depends: ``mode, addr_idx``
> +:Syntax:
> + ``echo addr1 addr2 [exclude] > addr_range``
> +
> + Where addr1 and addr2 define the range and addr1 < addr2.
> +
> + Optional exclude value:-
> +
> + - 0 for include
> + - 1 for exclude.
> +:Example:
> + ``$> echo 0x0000 0x2000 0 > addr_range``
> +
> +----
> +
> +:File: ``addr_single`` (rw)
> +:Trace Registers: ACVR[idx]
> +:Notes:
> + Set a single address comparator according to addr_idx. This
> + is used if the address comparator is used as part of event
> + generation logic etc.
> +
> +:Depends: ``addr_idx``
> +:Syntax:
> + ``echo addr1 > addr_single``
> +
> +----
> +
> +:File: ``addr_start`` (rw)
> +:Trace Registers: ACVR[idx], VISSCTLR
> +:Notes:
> + Set a trace start address comparator according to addr_idx.
> + Select comparator in control register.
> +
> +:Depends: ``addr_idx``
> +:Syntax:
> + ``echo addr1 > addr_start``
> +
> +----
> +
> +:File: ``addr_stop`` (rw)
> +:Trace Registers: ACVR[idx], VISSCTLR
> +:Notes:
> + Set a trace stop address comparator according to addr_idx.
> + Select comparator in control register.
> +
> +:Depends: ``addr_idx``
> +:Syntax:
> + ``echo addr1 > addr_stop``
> +
> +----
> +
> +:File: ``addr_context`` (rw)
> +:Trace Registers: ACATR[idx,{6:4}]
> +:Notes:
> + Link context ID comparator to address comparator addr_idx
> +
> +:Depends: ``addr_idx``
> +:Syntax:
> + ``echo ctxt_idx > addr_context``
> +
> + Where ctxt_idx is the index of the linked context id / vmid
> + comparator.
> +
> +----
> +
> +:File: ``addr_ctxtype`` (rw)
> +:Trace Registers: ACATR[idx,{3:2}]
> +:Notes:
> + Input value string. Set type for linked context ID comparator
> +
> +:Depends: ``addr_idx``
> +:Syntax:
> + ``echo type > addr_ctxtype``
> +
> + Type one of {all, vmid, ctxid, none}
> +:Example:
> + ``$> echo ctxid > addr_ctxtype``
> +
> +----
> +
> +:File: ``addr_exlevel_s_ns`` (rw)
> +:Trace Registers: ACATR[idx,{14:8}]
> +:Notes:
> + Set the ELx secure and non-secure matching bits for the
> + selected address comparator
> +
> +:Depends: ``addr_idx``
> +:Syntax:
> + ``echo val > addr_exlevel_s_ns``
> +
> + val is a 7 bit value for exception levels to exclude. Input
> + value shifted to correct bits in register.
> +:Example:
> + ``$> echo 0x4F > addr_exlevel_s_ns``
> +
> +----
> +
> +:File: ``addr_instdatatype`` (rw)
> +:Trace Registers: ACATR[idx,{1:0}]
> +:Notes:
> + Set the comparator address type for matching. Driver only
> + supports setting instruction address type.
> +
> +:Depends: ``addr_idx``
> +
> +----
> +
> +:File: ``addr_cmp_view`` (ro)
> +:Trace Registers: ACVR[idx, idx+1], ACATR[idx], VIIECTLR
> +:Notes:
> + Read the currently selected address comparator. If part of
> + address range then display both addresses.
> +
> +:Depends: ``addr_idx``
> +:Syntax:
> + ``cat addr_cmp_view``
> +:Example:
> + ``$> cat addr_cmp_view``
> +
> + ``addr_cmp[0] range 0x0 0xffffffffffffffff include ctrl(0x4b00)``
> +
> +----
> +
> +:File: ``nr_addr_cmp`` (ro)
> +:Trace Registers: From IDR4
> +:Notes:
> + Number of address comparator pairs
> +
> +----
> +
> +:File: ``sshot_idx`` (rw)
> +:Trace Registers: None
> +:Notes:
> + Select single shot register set.
> +
> +----
> +
> +:File: ``sshot_ctrl`` (rw)
> +:Trace Registers: SSCCR[idx]
> +:Notes:
> + Access a single shot comparator control register.
> +
> +:Depends: ``sshot_idx``
> +:Syntax:
> + ``echo val > sshot_ctrl``
> +
> + Writes val into the selected control register.
> +
> +----
> +
> +:File: ``sshot_status`` (ro)
> +:Trace Registers: SSCSR[idx]
> +:Notes:
> + Read a single shot comparator status register
> +
> +:Depends: ``sshot_idx``
> +:Syntax:
> + ``cat sshot_status``
> +
> + Read status.
> +:Example:
> + ``$> cat sshot_status``
> +
> + ``0x1``
> +
> +----
> +
> +:File: ``sshot_pe_ctrl`` (rw)
> +:Trace Registers: SSPCICR[idx]
> +:Notes:
> + Access a single shot PE comparator input control register.
> +
> +:Depends: ``sshot_idx``
> +:Syntax:
> + ``echo val > sshot_pe_ctrl``
> +
> + Writes val into the selected control register.
> +
> +----
> +
> +:File: ``ns_exlevel_vinst`` (rw)
> +:Trace Registers: VICTLR{23:20}
> +:Notes:
> + Program non-secure exception level filters. Set / clear NS
> + exception filter bits. Setting ‘1’ excludes trace from the
> + exception level.
> +
> +:Syntax:
> + ``echo bitfield > ns_exlevel_viinst``
> +
> + Where bitfield contains bits to set clear for EL0 to EL2
> +:Example:
> + ``%> echo 0x4 > ns_exlevel_viinst``
> +
> + Excludes EL2 NS trace.
> +
> +----
> +
> +:File: ``vinst_pe_cmp_start_stop`` (rw)
> +:Trace Registers: VIPCSSCTLR
> +:Notes:
> + Access PE start stop comparator input control registers
> +
> +----
> +
> +:File: ``bb_ctrl`` (rw)
> +:Trace Registers: BBCTLR
> +:Notes:
> + Define ranges that Branch Broadcast will operate in.
> + Default (0x0) is all addresses.
> +
> +:Depends: BB enabled.
> +
> +----
> +
> +:File: ``cyc_threshold`` (rw)
> +:Trace Registers: CCCTLR
> +:Notes:
> + Set the threshold for which cycle counts will be emitted.
> + Error if attempt to set below minimum defined in IDR3, masked
> + to width of valid bits.
> +
> +:Depends: CC enabled.
> +
> +----
> +
> +:File: ``syncfreq`` (rw)
> +:Trace Registers: SYNCPR
> +:Notes:
> + Set trace synchronisation period. Power of 2 value, 0 (off)
> + or 8-20. Driver defaults to 12 (every 4096 bytes).
> +
> +----
> +
> +:File: ``cntr_idx`` (rw)
> +:Trace Registers: none
> +:Notes:
> + Select the counter to access
> +
> +:Syntax:
> + ``echo idx > cntr_idx``
> +
> + Where idx < nr_cntr
> +
> +----
> +
> +:File: ``cntr_ctrl`` (rw)
> +:Trace Registers: CNTCTLR[idx]
> +:Notes:
> + Set counter control value.
> +
> +:Depends: ``cntr_idx``
> +:Syntax:
> + ``echo val > cntr_ctrl``
> +
> + Where val is per ETMv4 spec.
> +
> +----
> +
> +:File: ``cntrldvr`` (rw)
> +:Trace Registers: CNTRLDVR[idx]
> +:Notes:
> + Set counter reload value.
> +
> +:Depends: ``cntr_idx``
> +:Syntax:
> + ``echo val > cntrldvr``
> +
> + Where val is per ETMv4 spec.
> +
> +----
> +
> +:File: ``nr_cntr`` (ro)
> +:Trace Registers: From IDR5
> +
> +:Notes:
> + Number of counters implemented.
> +
> +----
> +
> +:File: ``ctxid_idx`` (rw)
> +:Trace Registers: None
> +:Notes:
> + Select the context ID comparator to access
> +
> +:Syntax:
> + ``echo idx > ctxid_idx``
> +
> + Where idx < numcidc
> +
> +----
> +
> +:File: ``ctxid_pid`` (rw)
> +:Trace Registers: CIDCVR[idx]
> +:Notes:
> + Set the context ID comparator value
> +
> +:Depends: ``ctxid_idx``
> +
> +----
> +
> +:File: ``ctxid_masks`` (rw)
> +:Trace Registers: CIDCCTLR0, CIDCCTLR1, CIDCVR<0-7>
> +:Notes:
> + Pair of values to set the byte masks for 1-8 context ID
> + comparators. Automatically clears masked bytes to 0 in CID
> + value registers.
> +
> +:Syntax:
> + ``echo m3m2m1m0 [m7m6m5m4] > ctxid_masks``
> +
> + 32 bit values made up of mask bytes, where mN represents a
> + byte mask value for Context ID comparator N.
> +
> + Second value not required on systems that have fewer than 4
> + context ID comparators
> +
> +----
> +
> +:File: ``numcidc`` (ro)
> +:Trace Registers: From IDR4
> +:Notes:
> + Number of Context ID comparators
> +
> +----
> +
> +:File: ``vmid_idx`` (rw)
> +:Trace Registers: None
> +:Notes:
> + Select the VM ID comparator to access.
> +
> +:Syntax:
> + ``echo idx > vmid_idx``
> +
> + Where idx < numvmidc
> +
> +----
> +
> +:File: ``vmid_val`` (rw)
> +:Trace Registers: VMIDCVR[idx]
> +:Notes:
> + Set the VM ID comparator value
> +
> +:Depends: ``vmid_idx``
> +
> +----
> +
> +:File: ``vmid_masks`` (rw)
> +:Trace Registers: VMIDCCTLR0, VMIDCCTLR1, VMIDCVR<0-7>
> +:Notes:
> + Pair of values to set the byte masks for 1-8 VM ID comparators.
> + Automatically clears masked bytes to 0 in VMID value registers.
> +
> +:Syntax:
> + ``echo m3m2m1m0 [m7m6m5m4] > vmid_masks``
> +
> + Where mN represents a byte mask value for VMID comparator N.
> + Second value not required on systems that have fewer than 4
> + VMID comparators.
> +
> +----
> +
> +:File: ``numvmidc`` (ro)
> +:Trace Registers: From IDR4
> +:Notes:
> + Number of VMID comparators
> +
> +----
> +
> +:File: ``res_idx`` (rw)
> +:Trace Registers: None.
> +:Notes:
> + Select the resource selector control to access. Must be 2 or
> + higher as selectors 0 and 1 are hardwired.
> +
> +:Syntax:
> + ``echo idx > res_idx``
> +
> + Where 2 <= idx < nr_resource x 2
> +
> +----
> +
> +:File: ``res_ctrl`` (rw)
> +:Trace Registers: RSCTLR[idx]
> +:Notes:
> + Set resource selector control value. Value per ETMv4 spec.
> +
> +:Depends: ``res_idx``
> +:Syntax:
> + ``echo val > res_cntr``
> +
> + Where val is per ETMv4 spec.
> +
> +----
> +
> +:File: ``nr_resource`` (ro)
> +:Trace Registers: From IDR4
> +:Notes:
> + Number of resource selector pairs
> +
> +----
> +
> +:File: ``event`` (rw)
> +:Trace Registers: EVENTCTRL0R
> +:Notes:
> + Set up to 4 implemented event fields.
> +
> +:Syntax:
> + ``echo ev3ev2ev1ev0 > event``
> +
> + Where evN is an 8 bit event field. Up to 4 event fields make up the
> + 32-bit input value. Number of valid fields is implementation dependent,
> + defined in IDR0.
> +
> +----
> +
> +:File: ``event_instren`` (rw)
> +:Trace Registers: EVENTCTRL1R
> +:Notes:
> + Choose events which insert event packets into trace stream.
> +
> +:Depends: EVENTCTRL0R
> +:Syntax:
> + ``echo bitfield > event_instren``
> +
> + Where bitfield is up to 4 bits according to number of event fields.
> +
> +----
> +
> +:File: ``event_ts`` (rw)
> +:Trace Registers: TSCTLR
> +:Notes:
> + Set the event that will generate timestamp requests.
> +
> +:Depends: ``TS activated``
> +:Syntax:
> + ``echo evfield > event_ts``
> +
> + Where evfield is an 8 bit event selector.
> +
> +----
> +
> +:File: ``seq_idx`` (rw)
> +:Trace Registers: None
> +:Notes:
> + Sequencer event register select - 0 to 2
> +
> +----
> +
> +:File: ``seq_state`` (rw)
> +:Trace Registers: SEQSTR
> +:Notes:
> + Sequencer current state - 0 to 3.
> +
> +----
> +
> +:File: ``seq_event`` (rw)
> +:Trace Registers: SEQEVR[idx]
> +:Notes:
> + State transition event registers
> +
> +:Depends: ``seq_idx``
> +:Syntax:
> + ``echo evBevF > seq_event``
> +
> + Where evBevF is a 16 bit value made up of two event selectors,
> +
> + - evB : back
> + - evF : forwards.
> +
> +----
> +
> +:File: ``seq_reset_event`` (rw)
> +:Trace Registers: SEQRSTEVR
> +:Notes:
> + Sequencer reset event
> +
> +:Syntax:
> + ``echo evfield > seq_reset_event``
> +
> + Where evfield is an 8 bit event selector.
> +
> +----
> +
> +:File: ``nrseqstate`` (ro)
> +:Trace Registers: From IDR5
> +:Notes:
> + Number of sequencer states (0 or 4)
> +
> +----
> +
> +:File: ``nr_pe_cmp`` (ro)
> +:Trace Registers: From IDR4
> +:Notes:
> + Number of PE comparator inputs
> +
> +----
> +
> +:File: ``nr_ext_inp`` (ro)
> +:Trace Registers: From IDR5
> +:Notes:
> + Number of external inputs
> +
> +----
> +
> +:File: ``nr_ss_cmp`` (ro)
> +:Trace Registers: From IDR4
> +:Notes:
> + Number of Single Shot control registers
> +
> +----
> +
> +*Note:* When programming any address comparator the driver will tag the
> +comparator with a type used - i.e. RANGE, SINGLE, START, STOP. Once this tag
> +is set, then only the values can be changed using the same sysfs file / type
> +used to program it.
> +
> +Thus::
> +
> + % echo 0 > addr_idx ; select address comparator 0
> + % echo 0x1000 0x5000 0 > addr_range ; set address range on comparators 0,
> 1.
> + % echo 0x2000 > addr_start ; error as comparator 0 is a range comparator
> + % echo 2 > addr_idx ; select address comparator 2
> + % echo 0x2000 > addr_start ; this is OK as comparator 2 is unused.
> + % echo 0x3000 > addr_stop ; error as comparator 2 set as start address.
> + % echo 2 > addr_idx ; select address comparator 3
> + % echo 0x3000 > addr_stop ; this is OK
> +
> +To remove programming on all the comparators (and all the other hardware) use
> +the reset parameter::
> +
> + % echo 1 > reset
> +
> +
> +
> +The ‘mode’ sysfs parameter.
> +---------------------------
> +
> +This is a bitfield selection parameter that sets the overall trace mode for
> the
> +ETM. The table below describes the bits, using the defines from the driver
> +source file, along with a description of the feature these represent. Many
> +features are optional and therefore dependent on implementation in the
> +hardware.
> +
> +Bit assignments shown below:-
> +
> +----
> +
> +**bit (0):**
> + ETM_MODE_EXCLUDE
> +
> +**description:**
> + This is the default value for the include / exclude function when
> + setting address ranges. Set 1 for exclude range. When the mode
> + parameter is set this value is applied to the currently indexed
> + address range.
> +
> +
> +**bit (4):**
> + ETM_MODE_BB
> +
> +**description:**
> + Set to enable branch broadcast if supported in hardware [IDR0].
> +
> +
> +**bit (5):**
> + ETMv4_MODE_CYCACC
> +
> +**description:**
> + Set to enable cycle accurate trace if supported [IDR0].
> +
> +
> +**bit (6):**
> + ETMv4_MODE_CTXID
> +
> +**description:**
> + Set to enable context ID tracing if supported in hardware [IDR2].
> +
> +
> +**bit (7):**
> + ETM_MODE_VMID
> +
> +**description:**
> + Set to enable virtual machine ID tracing if supported [IDR2].
> +
> +
> +**bit (11):**
> + ETMv4_MODE_TIMESTAMP
> +
> +**description:**
> + Set to enable timestamp generation if supported [IDR0].
> +
> +
> +**bit (12):**
> + ETM_MODE_RETURNSTACK
> +**description:**
> + Set to enable trace return stack use if supported [IDR0].
> +
> +
> +**bit (13-14):**
> + ETM_MODE_QELEM(val)
> +
> +**description:**
> + ‘val’ determines level of Q element support enabled if
> + implemented by the ETM [IDR0]
> +
> +
> +**bit (19):**
> + ETM_MODE_ATB_TRIGGER
> +
> +**description:**
> + Set to enable the ATBTRIGGER bit in the event control register
> + [EVENTCTLR1] if supported [IDR5].
> +
> +
> +**bit (20):**
> + ETM_MODE_LPOVERRIDE
> +
> +**description:**
> + Set to enable the LPOVERRIDE bit in the event control register
> + [EVENTCTLR1], if supported [IDR5].
> +
> +
> +**bit (21):**
> + ETM_MODE_ISTALL_EN
> +
> +**description:**
> + Set to enable the ISTALL bit in the stall control register
> + [STALLCTLR]
> +
> +
> +**bit (23):**
> + ETM_MODE_INSTPRIO
> +
> +**description:**
> + Set to enable the INSTPRIORITY bit in the stall control register
> + [STALLCTLR] , if supported [IDR0].
> +
> +
> +**bit (24):**
> + ETM_MODE_NOOVERFLOW
> +
> +**description:**
> + Set to enable the NOOVERFLOW bit in the stall control register
> + [STALLCTLR], if supported [IDR3].
> +
> +
> +**bit (25):**
> + ETM_MODE_TRACE_RESET
> +
> +**description:**
> + Set to enable the TRCRESET bit in the viewinst control register
> + [VICTLR] , if supported [IDR3].
> +
> +
> +**bit (26):**
> + ETM_MODE_TRACE_ERR
> +
> +**description:**
> + Set to enable the TRCCTRL bit in the viewinst control register
> + [VICTLR].
> +
> +
> +**bit (27):**
> + ETM_MODE_VIEWINST_STARTSTOP
> +
> +**description:**
> + Set the initial state value of the ViewInst start / stop logic
> + in the viewinst control register [VICTLR]
> +
> +
> +**bit (30):**
> + ETM_MODE_EXCL_KERN
> +
> +**description:**
> + Set default trace setup to exclude kernel mode trace (see note a)
> +
> +
> +**bit (31):**
> + ETM_MODE_EXCL_USER
> +
> +**description:**
> + Set default trace setup to exclude user space trace (see note a)
> +
> +----
> +
> +*Note a)* On startup the ETM is programmed to trace the complete address
> space
> +using address range comparator 0. ‘mode’ bits 30 / 31 modify this setting to
> +set EL exclude bits for NS state in either user space (EL0) or kernel space
> +(EL1) in the address range comparator. (the default setting excludes all
> +secure EL, and NS EL2)
> +
> +Once the reset parameter has been used, and/or custom programming has been
> +implemented - using these bits will result in the EL bits for address
> +comparator 0 being set in the same way.
> +
> +*Note b)* Bits 2-3, 8-10, 15-16, 18, 22, control features that only work with
> +data trace. As A-profile data trace is architecturally prohibited in ETMv4,
> +these have been omitted here. Possible uses could be where a kernel has
> +support for control of R or M profile infrastructure as part of a
> heterogeneous
> +system.
> +
> +Bits 17, 28-29 are unused.
This is quite usefull - thanks for putting it together:
Reviewed-by: Mathieu Poirier <mathieu.poir...@linaro.org>
> --
> 2.17.1
>
