On Wed, 2003-02-26 at 22:46, Sheetal_Pandey wrote: > Hi Malcolm, > > I tried the following > dvbstream -o -f 1150 -p H -I 1 -s 28125 517 700. I used dvbtune instead of > dvbstream.It says could not lock to the given frequency.It shows that > freq=1150 S/R=28125 etc. Do I have to change some where else for it to take > these values.
I don't know. (I am not even sure I know what you are asking). Perhaps someone more familiar with dvbtools can answer. > > I changed the parameters as above for RTPi in channels.conf and ran ./vdr.I > am not very friendly with the menu on screen so I was not able to enter into > that.Up and down was fine. So is it working? Here is my channels.conf: RTPi:1150:h:S100.5E:28125:517:700:0:0:30:0:0:0 DW:1150:h:S100.5E:28125:2305:2306:0:0:1:0:0:0 RAIi:1150:h:S100.5E:28125:513:644:0:0:3:0:0:0 TVE:1150:h:S100.5E:28125:514:648:0:0:4:0:0:0 TV5 Asie:1150:h:S100.5E:28125:515:625:0:0:5:0:0:0 (RTP is first because that is what I am more interested in!) I have not added the radio yet. For this to work you need the following in your setup.conf LnbFrequHi = 0 LnbFrequLo = 0 LnbSLOF = 0 > > Regards, > Sheetal Pandey > > > -----Original Message----- > From: Malcolm Caldwell [mailto:[EMAIL PROTECTED] > Sent: Wednesday, February 26, 2003 12:18 PM > To: Sheetal_Pandey > Cc: [EMAIL PROTECTED] > Subject: Re: [linux-dvb] setting the proper transonder value > > > On Wed, 2003-02-26 at 14:35, Sheetal_Pandey wrote: > > Hi, > > > > I am using the Hauuppauge WinTV nexus-S card.I have tuned the antenna to > > ASIASAT 2.I am trying to lock the card to European bouque but since I am > > using the card for the first time ,I am not comfortable in giving the > proper > > values. > > > > I have another digital satellite receiver which is locked properly to > > European bouque ,I mean that the signal is proper. > > > > The downlink freq is 4000 MHZ,fec 3/4,Symbol rate 28.125 Mbaud.I am using > a > > C band LNB with local oscillator freq 5150.Can somebody help in filling > the > > proper values. > > I have this working - asiasat2 and European Bouquet. I am fairly sure > the command line for eg. dvbstream is: (for eg for RTP) > dvbstream -o -f 1150 -p H -I 1 -s 28125 517 700 > (I can't confirm this at the moment as vdr is currently running) > > The problem is that the dvb stuff assumes Ku band LNB where you tune to > L = freq - LOF. > > With c-band L = LOF - freq. > > (L is the frequency on the cable from the LNB to the card). > > Luckily most of the tools accept L band frequences directly. So to tune > to the European Bouquet you need to tune to 1150 (ie 5150 - 4000). > > In VDR I have set the LOF to 0 and I put 1150 in the channels.conf. > > I think that VDR could be modified to accept the real frequencies. All > that is needed is to put freq=abs(freq). > > (If freq - LOF = L, then LOF - freq = -L. By putting the abs in we get > the correct frequency) > > I must add that I have not tried this modification yet. (What do other > think? Klus?) > > > > > Regards, > > Sheetal Pandey > > > > > > ************************************************************************** > > > This email (including any attachments) is intended for the sole use of the > > intended recipient/s and may contain material that is CONFIDENTIAL AND > > PRIVATE COMPANY INFORMATION. Any review or reliance by others or copying > or > > distribution or forwarding of any or all of the contents in this message > is > > STRICTLY PROHIBITED. If you are not the intended recipient, please contact > > the sender by email and delete all copies; your cooperation in this regard > > is appreciated. > > ************************************************************************** > > > ************************************************************************** > This email (including any attachments) is intended for the sole use of the > intended recipient/s and may contain material that is CONFIDENTIAL AND > PRIVATE COMPANY INFORMATION. Any review or reliance by others or copying or > distribution or forwarding of any or all of the contents in this message is > STRICTLY PROHIBITED. If you are not the intended recipient, please contact > the sender by email and delete all copies; your cooperation in this regard > is appreciated. > ************************************************************************** > -- Info: To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as subject.
