[linux-dvb] Hauppauge WinTV Nexus-s recognized but not working

[Walter Schittek]

Hi,

I can't get any confirmation that my DVB card and driver are working 
together. Because I am a beginner with DVB, I would be happy about each 
single tip, perhaps something that is selfunderstood for you.

I have a Nexus-s Rev. 2.1 (model 564) with Tuner Alps BSRU6 and Philips
SAA7146A Chip. Nothing special or new, I suppose.
lspci -v shows that IRQ 11 is only used by this card and not shared.
Because I later want to install VDR, I use the DVB driver proposed there:
linux-dvb.2003-06-08.tar.bz2
(http://www.cadsoft.de/people/kls/vdr/download.htm)
make runs without errors or warnings.
make insmod gives one single warning:
Using /lib/modules/2.4.19-4GB/kernel/drivers/media/video/videodev.o
insmod: a module named videodev already exists
makedev.napi runs ok.
/var/log/messages says:
Jun 20 09:23:40 cardo kernel: DVB: registering new adapter 
(Technotrend/Hauppauge PCI rev2.1 or 2.2).
Jun 20 09:23:40 cardo kernel: PCI: Found IRQ 11 for device 01:0b.0
Jun 20 09:23:40 cardo kernel: saa7146_core.o: adjusting pci latency to 64
Jun 20 09:23:41 cardo kernel: stv0299.c: setup for tuner BSRU6, TDQB-S00x
Jun 20 09:23:41 cardo kernel: DVB: registering frontend 0:0 
(STV0299/TSA5059/SL1935 based)...
Jun 20 09:23:43 cardo kernel: DVB: AV7111(0) - firm f0240009, rtsl 
b0250018, vid 71010068, app 80002616
Jun 20 09:23:43 cardo kernel: DVB: AV7111(0) - firmware supports CI link 
layer interface
Jun 20 09:23:44 cardo kernel: av7110(0): adac type set to 0

Now I test whether it is recognized by xawtv: xawtv -hwscan
This is xawtv-3.86, running on Linux/i686 (2.4.19-4GB)
looking for available devices
port 55-55
    type : Xvideo, image scaler
    name : I810 Video Overlay
ioctl: VIDIOCGTUNER(tuner=0;name="";rangelow=0;rangehigh=0;flags=0x0 
[];mode=PAL;signal=0): Das Argument ist ungültig
/dev/video0: OK                         [ -device /dev/video0 ]
    type : v4l
    name : DVB Board
    flags: overlay capture tuner

When xawtv is started from console, it only shows a black screen, gives 
the same error message as above, and on every channel switch it gives an 
error like:
ioctl: VIDIOCSFREQ(long=884): Das Argument ist ungültig

Because I have no experience with xawtv, it is possible that I made 
something wrong with it. Do you have another idea how to test whether 
DVB card and driver are working?

During active xawtv, lsmod says:
dvb-ttpci             300436   1
evdev                   4352   0  (unused)
input                   3168   0  [dvb-ttpci evdev]
ves1820                 4028   0
stv0299                 6704   0  (unused)
grundig_29504-491       3584   0
grundig_29504-401       3944   0
alps_tdlb7              4044   0
alps_tdmb7              3748   0
alps_bsrv2              3928   0
dvb-core               38756   3  [dvb-ttpci ves1820 stv0299 
grundig_29504-491 grundig_29504-401 alps_tdlb7 alps_tdmb7 alps_bsrv2]

I am wondering about the "(unused)" entries. I thought, stv0299 would be 
the right module for my DVB card.

I have spent many many hours in testing but don't yet have any 
confirmation that DVB card and driver are working together.
Have I missed something?
How can I give options to the driver? Which options? I am no programmer 
and don't know how to do it.
A small problem still is that all modules are not loaded after restart 
of the computer. Which entries are needed for /etc/modules.conf?

Thanks for any tip

Walter

--

Walter Schittek
Steinweg 12
D - 35037 Marburg
Tel: 06421/889441
Fax: +49 6421 889446 (nachmittags)
eMail: [EMAIL PROTECTED]




--
Info:
To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as 
subject.