Hi! I've got a problem with a Hauppauge Nexus-S (Rev 2.2):
In my desktop computer everything works fine: * Suse 7.3 - kernel 2.4.16 * Linux DVB driver release 1.0.0-pre3 * vdr Version 1.2 DVB driver load without problems, I get a picture, sound and can switch channels. If I put the DVB-card into my VIA EPIA-M board (http://www.viavpsd.com/product/epia_m_spec.jsp?motherboardId=81) the DVB driver set does not load completely - here is the output from /var/log/messages: Jul 30 01:43:34 video kernel: Linux video capture interface: v1.00 Jul 30 01:43:36 video kernel: DVB: registering new adapter (Technotrend/Hauppauge PCI rev2.1 or 2.2). Jul 30 01:43:36 video kernel: saa7146_core.o: adjusting pci latency to 64 Jul 30 01:43:36 video kernel: dvb: debi test in bootarm() failed: 08000000 != 10325476 Jul 30 01:43:36 video kernel: RequestParameter error Jul 30 01:43:36 video kernel: DVB: AV7112048(0) - firm 5400d0d4, rtsl 0000ced5, vid 7ee3ced0, app f4e0ced0 Jul 30 01:43:36 video kernel: DVB: AV7112048(0) - firmware supports CI link layer interface Jul 30 01:43:36 video kernel: outcom error Jul 30 01:43:36 video kernel: outcom error Jul 30 01:43:36 video kernel: av7110(0): adac type set to 0 Jul 30 01:43:36 video kernel: outcom error Then I tried the DVB drivers 1.1.7 from Metzler bros.: again an error, but the output gives a hint about a problem with I2C. Jul 30 01:44:49 video kernel: Linux video capture interface: v1.00 Jul 30 01:44:49 video kernel: i2c-core.o: i2c core module version 2.6.2 (20011118) Jul 30 01:44:49 video kernel: i2c-core.o: driver stv0299 DVB demodulator registered. Jul 30 01:44:49 video kernel: i2c-core.o: driver ves1893 DVB demodulator registered. Jul 30 01:44:49 video kernel: i2c-core.o: driver ves1820 DVB demodulator registered. Jul 30 01:44:49 video kernel: i2c-core.o: driver tda8083 DVB demodulator registered. Jul 30 01:44:50 video kernel: dvb_register_adapter: registering new adapter (Technotrend/Hauppauge PCI rev2.1). Jul 30 01:44:50 video kernel: saa7146_core.o: saa7146: bus:0, rev:1, mem:0xd084e000. Jul 30 01:44:50 video kernel: error reading I2C reg Jul 30 01:44:50 video kernel: i2c-core.o: adapter saa7146 registered as adapter 0. Jul 30 01:44:50 video kernel: dvb: debi test in AV7110_boot() failed: 08000000 != 10325476 Jul 30 01:44:50 video kernel: av71100: AV7111109442951 - firm 7a73c626, rtsl ece0c626, vid 00000800, app 54761032 Jul 30 01:44:50 video kernel: av7110: Warning, firmware version is too old. System might be unstable!!! Jul 30 01:44:50 video kernel: av7110-0: Could not read MAC Jul 30 01:44:50 video kernel: av7110-0: MAC = 00 00 00 00 00 00 Jul 30 01:44:50 video kernel: dvb_register_device: register adapter0/demux0 @ minor: 4 (0x04) - dvbdev: c17f15e0 Jul 30 01:44:50 video kernel: dvb_register_device: register adapter0/dvr0 @ minor: 5 (0x05) - dvbdev: c17f1b20 Jul 30 01:44:50 video kernel: dvb_register_device: register adapter0/net0 @ minor: 7 (0x07) - dvbdev: c17f1a60 Jul 30 01:44:50 video kernel: dvb_register_device: register adapter0/video0 @ minor: 0 (0x00) - dvbdev: c17f17e0 Jul 30 01:44:50 video kernel: dvb_register_device: register adapter0/audio0 @ minor: 1 (0x01) - dvbdev: c17f1a20 Jul 30 01:44:50 video kernel: dvb_register_device: register adapter0/osd0 @ minor: 8 (0x08) - dvbdev: c17f1b60 Jul 30 01:44:50 video kernel: dvb_register_device: register adapter0/ca0 @ minor: 6 (0x06) - dvbdev: c17f1ba0 DVB card gets an IRQ. Things I already tried: *Switching PnP in BIOS on/off *Switching several onboard components on/off (to change IRQ configuration) *used different kernel 2.4.21 from kernel.org *kernel tweaking (I2C as modules or compiled into kernel, etc.) I spent about a week to solve this problem, but no success. Nothing changed the situation with this EPIA board. What's special about this board: it has an additional I2C connector. Perhaps this causes the trouble? Any help is appreciated. Regards A.Rosenberg -- Info: To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as subject.
