Hi! I have problems with a skystar2 card (tested with the latest 1.0.1 driver):
bash# ./apps/szap/szap -c ~/Astra1 -n 73 reading channels from file '/home/rebel/Astra1' zapping to 'CNN Int.': sat 0, frequency = 11778 MHz V, symbolrate 27500000, vpid = 0x00a5, apid = 0x0064 using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' status 00 | signal 0000 | snr 73f5 | ber 00000000 | unc 00000000 | status 1b | signal 3dc5 | snr c7d1 | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1b | signal 3dc1 | snr c7e9 | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1b | signal 3dbf | snr c7bd | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1b | signal 3dba | snr c7e9 | ber 00000000 | unc 00000000 | FE_HAS_LOCK status 1b | signal 3dbc | snr c7f5 | ber 00000000 | unc 00000000 | FE_HAS_LOCK ... The status 1b is suspicious, so I'm not very surprised that I don't get any output, for example with 'dvbstream -o -f 12441 -p v -s 27500 512 660': dvbstream v0.4pre3 - (C) Dave Chapman 2001 Released under the GPL. Latest version available from http://www.linuxstb.org/ Using DVB card "Zarlink MT312" tuning DVB-S to L-Band:0, Pol:V Srate=27500000, 22kHz=off polling.... Getting frontend event FE_STATUS: FE_TIMEDOUT Not able to lock to the signal on the given frequency kernel log: Technisat SkyStar2 driver loading skystar2.c: FlexCopII(rev.130) chip found skystar2.c: MAC address = 00:d0:d7:04:91:c7:00:00 skystar2.c: key = b2 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 DVB: registering new adapter (PCI device 13d0:2103 (Techsan Electronics Co Ltd)). mt312.c: setup for VP310 DVB: registering frontend 0:0 (Zarlink MT312)... flexcop_diseqc_ioctl: SEC_TONE_OFF, 1 flexcop_diseqc_ioctl: SEC_VOLTAGE_13, 0 flexcop_diseqc_ioctl: SEC_TONE_ON, 0 synth dword = 24d08482 synth dword = 24de8482 The new driver with added support for the revision 2.6 is even worse (got it from http://www.gdv.uni-hannover.de/~peinecke/skystar2): bash# ./apps/szap/szap -c ~/Astra1 -n 73 reading channels from file '/home/rebel/Astra1' zapping to 'CNN Int.': sat 0, frequency = 11778 MHz V, symbolrate 27500000, vpid = 0x00a5, apid = 0x0064 using '/dev/dvb/adapter0/frontend0' and '/dev/dvb/adapter0/demux0' status 00 | signal 0000 | snr 81cb | ber 00000000 | unc 00000000 | status 00 | signal 20db | snr 87cd | ber 00000000 | unc 00000000 | status 01 | signal 3dae | snr bf7f | ber 00000000 | unc 00000000 | status 00 | signal 3df2 | snr 8329 | ber 00000000 | unc 00000000 | ... So, any hints what I could try next? Thanks Michal -- Info: To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as subject.
