Hello everybody, I'm trying to use Deutsche Telekom's "T-DSL via Satellit", an account which -despite its name- has nothing to do with DSL, but does boost-up low bandwith connections with a local proxy software by using Astra DVB-S to have a broadband downstream channel. (I just mention that to make clear that I really don't want to watch TV, I just need the network device.)
My setup is kernel 2.4.23, bttv 0.9.12, and dvb-kernel taken fresh from CVS on sunday. dvbtune is from the Debian package, 0.3+cvs20030922-2 The machine is an older K6 133MHz with 64MB RAM which sits in a closet serving as the headless router for my home LAN. Everything went fine so far, the modules are loaded successfully: Dec 1 09:52:53 scrag kernel: bttv: using 8 buffers with 2080k (520 pages) each for capture Dec 1 09:52:53 scrag kernel: bttv: Bt8xx card found (0). Dec 1 09:52:53 scrag kernel: bttv0: Bt878 (rev 17) at 00:0b.0, irq: 9, latency: 32, mmio: 0xe0004000 Dec 1 09:52:53 scrag kernel: bttv0: detected: Pinnacle PCTV Sat [card=94], PCI subsystem ID is 11bd:001c Dec 1 09:52:53 scrag kernel: bttv0: using: Pinnacle PCTV Sat [card=94,insmod option] Dec 1 09:52:53 scrag kernel: bttv0: gpio: en=00000000, out=00000000 in=009f00fc [init] Dec 1 09:52:53 scrag kernel: i2c-core.o: adapter bt878 #0 [hw] registered as adapter 0. Dec 1 09:52:53 scrag kernel: bttv0: using tuner=-1 Dec 1 09:52:53 scrag kernel: bttv0: registered device video0 Dec 1 09:52:53 scrag kernel: bttv0: registered device vbi0 Dec 1 09:52:53 scrag kernel: bttv0: PLL: 28636363 => 35468950 . ok Dec 1 09:52:53 scrag kernel: i2c-core.o: driver i2c TV tuner driver registered.Dec 1 09:53:35 scrag kernel: bt878: AUDIO driver version 0.0.0 loaded Dec 1 09:53:35 scrag kernel: bt878: Bt878 AUDIO function found (0). Dec 1 09:53:35 scrag kernel: bt878(0): Bt878 (rev 17) at 00:0b.1, irq: 9, latency: 32, memory: 0xe0005000 Dec 1 09:53:36 scrag kernel: DVB: registering new adapter (Pin). Dec 1 09:53:39 scrag kernel: DVB: registering frontend 0:0 (Conexant CX24110 with CX24108 tuner, aka HM1221/HM1811)... When I try to tune the card with dvbtune, I get FE_TIMEDOUT and cannot lock the frequency: # dvbtune -c 0 -f 10773250 -p H -s 22000 -n 251 Using DVB card "Conexant CX24110 with CX24108 tuner, aka HM1221/HM1811" tuning DVB-S to L-Band:-1073742492, Pol:H Srate=22000000, 22kHz=off polling.... Getting frontend event FE_STATUS: FE_HAS_SIGNAL FE_HAS_CARRIER FE_HAS_VITERBI polling.... Getting frontend event FE_STATUS: FE_HAS_SIGNAL FE_HAS_VITERBI polling.... Getting frontend event FE_STATUS: polling.... Getting frontend event FE_STATUS: FE_HAS_SIGNAL polling.... Getting frontend event FE_STATUS: FE_HAS_SIGNAL FE_TIMEDOUT FE_HAS_CARRIER Not able to lock to the signal on the given frequency I've done RTFM thoroughly but didn't find any solution. The Metzler drivers don't help, their cx24110 module seems to be outdated. I didn't find out how to configure the card with szap, if that comes to someones mind (I dont wanna TV, wanna network). The digital TV receiver set connected to the same dish reports a signal quality of only 73%, could this be the cause of the problem? Is there any software solution, or do I have to look for another DVB-S card? TIA, HAND Holger Spielmann -- Info: To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as subject.
