I have the same card and the same problems (TwinHan with CI, Card 113, I got the the card two weeks ago). I added the modules to /etc/modules and then I inserted a CAM with smart card. This didn't help. Then I waited a week and suddenly it was working without changes. After rebooting the system it failed again. I rebooted the system more than ten times and suddenly it was working again. The CAM is not needed, but I think the message "dst_check_ci: write not successful, maybe no card?" means that there is no cam or smart card. The most times I boot my system the card is not working, but sometimes it works. I don't know why. I am using linux 2.4.24 from CT (http://www.heise.de/ct/ftp/projekte/vdr/), but the system is knoppix/debian. > I'm trying to get some Twinhan VisionPlus (I can't locate a model > number) cards working with Linux 2.6.5. The modules load, but the > devices are not working (not existing in devfs), and dmesg shows some > ugly things: > > Linux video capture interface: v1.00 > bttv: driver version 0.9.12 loaded > bttv: using 8 buffers with 2080k (520 pages) each for capture > bttv: Bt8xx card found (0). > bttv0: Bt878 (rev 17) at 0000:03:04.0, irq: 11, latency: 64, mmio: > 0xdf8fe000 > bttv0: detected: Twinhan VisionPlus DVB-T [card=113], PCI subsystem ID is > 1822:0001 > bttv0: using: Twinhan DST + clones [card=113,autodetected] > bttv0: gpio: en=00000000, out=00000000 in=00f500fd [init] > bttv0: using tuner=4 > bttv0: add subdevice "dvb0" > bt878: AUDIO driver version 0.0.0 loaded > bt878: Bt878 AUDIO function found (0). > bt878(0): Bt878 (rev 17) at 03:04.1, irq: 11, latency: 64, memory: > 0xdf8ff000 > attach: checking "bt878 #0 [sw]" > find by pci: checking "bt878 #0 [sw]" > attach: "bt878 #0 [sw]", to card 0 > DVB: registering new adapter (DST). > dst_attach: check ci > bt878 find by dvb adap: checking "DST" > write_dst writing 0x00 0x06 0x00 0x00 0x00 0x00 0x00 0xfa > write_dst: write_dst error (err == -121, len == 0x08, b0 == 0x00) > write_dst: write_dst error (err == -121, len == 0x08, b0 == 0x00) > write_dst: write_dst error (err == -121, len == 0x08, b0 == 0x00) > write_dst: write_dst error (err == -121, len == 0x08, b0 == 0x00) > dst_check_ci: write not successful, maybe no card? > > Does this mean the card is not supported? Is there some magic I have > missed? I get this from lspci: > > 03:04.0 Multimedia video controller: Brooktree Corporation Bt878 Video > Capture (rev 11) > Subsystem: Unknown device 1822:0001 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR+ FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 64 (4000ns min, 10000ns max) > Interrupt: pin A routed to IRQ 11 > Region 0: Memory at df8fe000 (32-bit, prefetchable) [size=4K] > Capabilities: [44] Vital Product Data > Capabilities: [4c] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > 03:04.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture > (rev 11) > Subsystem: Unknown device 1822:0001 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- > ParErr- Stepping- SERR+ FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 64 (1000ns min, 63750ns max) > Interrupt: pin A routed to IRQ 11 > Region 0: Memory at df8ff000 (32-bit, prefetchable) [size=4K] > Capabilities: [44] Vital Product Data > Capabilities: [4c] Power Management version 2 > Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA > PME(D0-,D1-,D2-,D3hot-,D3cold-) > Status: D0 PME-Enable- DSel=0 DScale=0 PME- > > -- > M�ns Rullg�rd > [EMAIL PROTECTED] > > > > -- > Info: > To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe > linux-dvb" as subject. >
-- "Sie haben neue Mails!" - Die GMX Toolbar informiert Sie beim Surfen! Jetzt aktivieren unter http://www.gmx.net/info -- Info: To unsubscribe send a mail to [EMAIL PROTECTED] with "unsubscribe linux-dvb" as subject.
