Hi Hans, thanks for your answer, I say what I tryed; your dmesg output looks quite good. In fact, the only line that irritates me is the line with
> > xc2028 4-0061: Error on line 1063: -5 > > This line indicates an i2c-communication problem with the tuner. > As it happens BEFORE the XC3028 firmware is loaded, it cannot have > anything to do with the xc3028 firmware. > Therefore, I suspect something either with the general setup of the > Expresscard or a DiB firmware that does not > 100% support your device. Have you tried a later firmware? I was trying latest firmware (I think): dvb-usb-dib0700-03-pre1.fw I also tryed the previous; dvb-usb-dib0700-1.10.fw And an other one; dvb-usb-dib0700-01.fw This last one doesn't give any error, but I also can not see anything on scanning. I send you the dmesg. Feb 13 19:14:50: xc2028 7-0061: Loading firmware for type=D2620 DTV8 (208), > id 0000000000000000. > Feb 13 19:14:50: xc2028 7-0061: Device is Xceive 3028 version 1.0, > firmware version 2.7 > Feb 13 19:14:50: dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 This last lines are a little bit different from the ones I have... Perhaps something about the firmware modification. I did not change the extract_firmware.pl file (in fact, it is not useable > for the Mod7700.sys driver, but expects the driver > file hcw85bda.sys), but just used a hex editor to replace the ID > 0x64000200 by 0x60000200. I tryed to do the same but I can't find 0x64000200 on the hex... Could you send me your firmware just to try? certainly a good idea to use an amplified antenna. Have you got another > DVB-t device that works with a passive > antenna in the same area where you use your new device? I use the same device on XP and it detects some channels. When I try to scan with kaffeine I don't see any SNR or anything so I guess the comunication with xc3028 is failing. Thanks again for your answer. I also send this mail to pattrick who probably knows better the dibcom firmware stuff.
[ 4107.196000] usb 1-1: new high speed USB device using ehci_hcd and address 9 [ 4107.328000] usb 1-1: configuration #1 chosen from 1 choice [ 4107.328000] dvb-usb: found a 'Pinnacle Expresscard 320cx' in cold state, will try to load a firmware [ 4107.332000] dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw' [ 4107.516000] dib0700: firmware started successfully. [ 4108.020000] dvb-usb: found a 'Pinnacle Expresscard 320cx' in warm state. [ 4108.020000] dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer. [ 4108.020000] DVB: registering new adapter (Pinnacle Expresscard 320cx) [ 4108.300000] DVB: registering frontend 0 (DiBcom 7000PC)... [ 4108.300000] xc2028 4-0061: type set to XCeive xc2028/xc3028 tuner [ 4108.300000] input: IR-receiver inside an USB DVB receiver as /class/input/input13 [ 4108.300000] dvb-usb: schedule remote query interval to 150 msecs. [ 4108.300000] dvb-usb: Pinnacle Expresscard 320cx successfully initialized and connected. [ 4136.252000] xc2028 4-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7 [ 4136.256000] dib0700: stk7700ph_xc3028_callback: XC2028_TUNER_RESET 0 [ 4136.256000] [ 4136.272000] xc2028 4-0061: Loading firmware for type=BASE F8MHZ (3), id 0000000000000000. [ 4136.272000] dib0700: stk7700ph_xc3028_callback: XC2028_TUNER_RESET 0 [ 4136.272000] [ 4139.272000] xc2028 4-0061: Loading firmware for type=D2620 DTV8 (208), id 0000000000000000. [ 4139.324000] xc2028 4-0061: Loading SCODE for type=DTV8 SCODE HAS_IF_5400 (60000200), id 0000000000000000. [ 4139.368000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4139.384000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4139.384000] [ 4141.004000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4141.020000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4141.020000] [ 4142.532000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4142.548000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4142.548000] [ 4144.160000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4144.176000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4144.176000] [ 4145.696000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4145.712000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4145.712000] [ 4147.324000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4147.340000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4147.340000] [ 4148.852000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4148.868000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4148.868000] [ 4150.484000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4150.500000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4150.500000] [ 4152.016000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4152.032000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4152.032000] [ 4153.644000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4153.660000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4153.660000] [ 4155.184000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4155.204000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4155.204000] [ 4156.816000] xc2028 4-0061: Device is Xceive 3028 version 1.0, firmware version 2.7 [ 4156.832000] dib0700: stk7700ph_xc3028_callback: XC2028_RESET_CLK 1 [ 4156.832000]
_______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
