hy, the wiki is not up2date.
Twinhan VP-1041 support is now in the mantis tree (inkl. multiproto) hg clone http://jusst.de/hg/mantis but for me, the old initialization parameters works much better. with the new ones i get only a destructed picture (unwatchable). gernot On Monday 18 February 2008 20:05:03 Tim Hewett wrote: > I'm trying to get a new Technisat Skystar HD2 working. It looks like > it is a Twinhan VP-1041/Azurewave AD SP400 rebadge. > > The card hardware and satellite feed has been confirmed to work ok > under Windows using Technisat's software. > > I am using the current multiproto DVB drivers, downloaded today. These > were patched, built and installed successfully as described for the > Azurewave AD SP400 in the linuxdvb wiki, but the card was not > recognised on bootup even though it was allocated a DVB adaptor > number. This appeared in dmesg: > > [ 57.359723] found a UNKNOWN PCI UNKNOWN device on (01:06.0), > [ 57.359802] Mantis Rev 1 [1ae4:0001], irq: 16, latency: 32 > [ 57.359858] memory: 0xe5100000, mmio: 0xffffc200000fc000 > [ 57.363015] MAC Address=[00:08:c9:e0:26:92] > [ 57.363133] mantis_alloc_buffers (0): DMA=0x1b7a0000 > cpu=0xffff81001b7a0000 size=65536 > [ 57.363242] mantis_alloc_buffers (0): RISC=0x1ae24000 > cpu=0xffff81001ae24000 size=1000 > [ 57.363348] DVB: registering new adapter (Mantis dvb adapter) > > > This is the output of lspci -vvn: > > 01:06.0 0480: 1822:4e35 (rev 01) > Subsystem: 1ae4:0001 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (2000ns min, 63750ns max) > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at e5100000 (32-bit, prefetchable) [size=4K] > > This is the output of lsusb -vv: > > 01:06.0 Multimedia controller: Twinhan Technology Co. Ltd Mantis DTV > PCI Bridge Controller [Ver 1.0] (rev 01) > Subsystem: Unknown device 1ae4:0001 > Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- > Stepping- SERR- FastB2B- > Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- > <TAbort- <MAbort- >SERR- <PERR- > Latency: 32 (2000ns min, 63750ns max) > Interrupt: pin A routed to IRQ 16 > Region 0: Memory at e5100000 (32-bit, prefetchable) [size=4K] > > Note that subsystem IDs 1ae4:0001 are different to those listed in the > wiki for the Azurewave (1822:0031). > > I changed #define MANTIS_VP_1041_DVB_S2 in linux/drivers/media/dvb/ > mantis/mantis_vp1041.h from 0x0031 to 0x0001, which changed the dmesg > output on reboot to this: > > [ 59.546375] found a VP-1041 PCI DVB-S/DVB-S2 device on (01:06.0), > [ 59.546456] Mantis Rev 1 [1ae4:0001], irq: 16, latency: 32 > [ 59.546512] memory: 0xe5100000, mmio: 0xffffc200000fc000 > [ 59.549609] MAC Address=[00:08:c9:e0:26:92] > [ 59.549719] mantis_alloc_buffers (0): DMA=0x1b7b0000 > cpu=0xffff81001b7b0000 size=65536 > [ 59.549827] mantis_alloc_buffers (0): RISC=0x1af43000 > cpu=0xffff81001af43000 size=1000 > [ 59.549933] DVB: registering new adapter (Mantis dvb adapter) > [ 60.137583] stb0899_attach: Attaching STB0899 > [ 60.137665] mantis_frontend_init (0): found STB0899 DVB-S/DVB-S2 > frontend @0x68 > [ 60.152161] stb6100_attach: Attaching STB6100 > [ 60.168021] DVB: registering frontend 3 (STB0899 Multistandard)... > > So that change seemed to cause the card to be recognised. > > Then I tried the replacement scan and szap as suggested by the > Azurewave wiki, but the card will not tune. > > So it appears to be almost working, but I'm not sure what tests to try > or changes to make to see if it will work. _______________________________________________ linux-dvb mailing list linux-dvb@linuxtv.org http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb