Well, Well, to start, some good news : I have configured a new fai server. Now everything is ok for ata disk : I can install a demohost with ata, but (bad news !) not with SATA. The modules are now ok and they can be loaded. When I try an installation with SATA, I've got those error messages :
In fai.log : Calling task_defclass 10-base-classes OK. Discovering hardware: sata_nv tulip Loading sata_nv: Skipping tulip; assuming it is compiled into the kernel. Video card detected: 20-hwdetect.source OK. 50-host-classes OK. Calling task_defvar ++ FAI_CONSOLEFONT= ++ FAI_KEYMAP=fr-latin1 ++ UTC=yes ++ time_zone=Europe/Paris ++ rootpw=$1$kBnWcO.E$djxB128U7dMkrltJHPf6d1 ++ moduleslist=usbkbd ehci-hcd ohci-hcd uhci-hcd usbhid psmouse ++ FAI_ACTION=install Loading keymap(s) fr-latin1 ...done. Calling task_action FAI_ACTION: install Performing FAI installation. All data may be overwritten! Calling task_install Calling task_partition Partitioning local harddisks setup_harddisks version 0.38fai Probing disks: Disks found: Using config file: /fai/disk_config/FAIBASE ERROR: could not read device /dev/ Mapping disk name disk1 to setup_harddisks version 0.38fai Probing disks: Disks found: Using config file: /fai/disk_config/FAIBASE Mapping disk name disk1 to cp: cannot stat `/var/log/fai/current/disk_var.sh': No such file or directory Save log files via rsh to [EMAIL PROTECTED]:demohost/install-20060727_000151 rcmd: getaddrinfo: Name or service not known rcmd: getaddrinfo: Name or service not known setup_harddisks did not create /var/log/fai/current/disk_var.sh file. ------------------------- in kernel.log : klogd 1.4.1#17, log source = /proc/kmsg started. Inspecting /boot/System.map-2.6.16-fai-kernels Loaded 17531 symbols from /boot/System.map-2.6.16-fai-kernels. Symbols match kernel version 2.6.16. No module symbols loaded - kernel modules not enabled. <6>NET: Registered protocol family 10 <6>IPv6 over IPv4 tunneling driver <6>NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0 <6>NFORCE-CK804: chipset revision 242 <6>NFORCE-CK804: not 100%% native mode: will probe irqs later <6>NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller <6> ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA <6> ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA <7>Probing IDE interface ide0... <4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 <4>Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon! <7>eth3: no IPv6 routers present <6>usbcore: registered new driver usbfs <6>usbcore: registered new driver usbkbd <6>drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver <7>PCI: Setting latency timer of device 0000:00:02.1 to 64 <6>ehci_hcd 0000:00:02.1: EHCI Host Controller <6>ehci_hcd 0000:00:02.1: debug port 1 <7>PCI: cache line size of 64 is not supported by device 0000:00:02.1 <6>usb usb1: configuration #1 chosen from 1 choice <7>ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) <6>ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 <6>ohci_hcd 0000:00:02.0: irq 10, io mem 0xf6002000 <6>hub 2-0:1.0: USB hub found <6>hub 2-0:1.0: 10 ports detected <6>usbcore: registered new driver hiddev <6>usbcore: registered new driver usbmouse <6>drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver <5>SCSI subsystem initialized <6>Fusion MPT SPI Host driver 3.03.07 <7>sata_nv 0000:00:07.0: version 0.8 <7>PCI: Setting latency timer of device 0000:00:07.0 to 64 <6>ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD008 irq 10 <6>ata2: SATA link down (SStatus 0) <6>scsi1 : sata_nv <6>ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xE400 irq 11 <6>ata3: SATA link up 1.5 Gbps (SStatus 113) <3>irq 10: nobody cared (try booting with the "irqpoll" option) <4> [__report_bad_irq+43/105] __report_bad_irq+0x2b/0x69 <4> [note_interrupt+402/451] note_interrupt+0x192/0x1c3 <4> [handle_IRQ_event+34/78] handle_IRQ_event+0x22/0x4e <4> [__do_IRQ+157/207] __do_IRQ+0x9d/0xcf <4> [do_IRQ+25/36] do_IRQ+0x19/0x24 <4> [common_interrupt+26/32] common_interrupt+0x1a/0x20 <4> [default_idle+0/85] default_idle+0x0/0x55 <4> [default_idle+44/85] default_idle+0x2c/0x55 <4> [cpu_idle+88/109] cpu_idle+0x58/0x6d <4> [start_kernel+722/729] start_kernel+0x2d2/0x2d9 <3>handlers: <3>[pg0+542356459/1070003200] (usb_hcd_irq+0x0/0x57 [usbcore]) <3>[pg0+542843268/1070003200] (nv_interrupt+0x0/0x89 [sata_nv]) <0>Disabling IRQ #10 <6>ata4: SATA link down (SStatus 0) <6>scsi3 : sata_nv Thanks for your help ;-) Jean-Paul
