A few call sites inside mach-ixp4xx were still using the custom ixp4xx GPIO API with gpio_line_* accessors, convert all these to use the standard gpiolib functions instead. Also attempt to request and label all GPIOs before use.
Cc: Imre Kaloz <[email protected]> Cc: Krzysztof Halasa <[email protected]> Cc: Alexandre Courbot <[email protected]> Signed-off-by: Linus Walleij <[email protected]> --- arch/arm/mach-ixp4xx/dsmg600-setup.c | 16 +++++++++------- arch/arm/mach-ixp4xx/ixdp425-setup.c | 8 +++++--- arch/arm/mach-ixp4xx/nas100d-setup.c | 15 ++++++++------- arch/arm/mach-ixp4xx/nslu2-setup.c | 10 +++++----- 4 files changed, 27 insertions(+), 22 deletions(-) diff --git a/arch/arm/mach-ixp4xx/dsmg600-setup.c b/arch/arm/mach-ixp4xx/dsmg600-setup.c index 63de1b3..9095097 100644 --- a/arch/arm/mach-ixp4xx/dsmg600-setup.c +++ b/arch/arm/mach-ixp4xx/dsmg600-setup.c @@ -26,6 +26,7 @@ #include <linux/reboot.h> #include <linux/i2c.h> #include <linux/i2c-gpio.h> +#include <linux/gpio.h> #include <mach/hardware.h> @@ -161,11 +162,8 @@ static struct platform_device *dsmg600_devices[] __initdata = { static void dsmg600_power_off(void) { - /* enable the pwr cntl gpio */ - gpio_line_config(DSMG600_PO_GPIO, IXP4XX_GPIO_OUT); - - /* poweroff */ - gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH); + /* enable the pwr cntl and drive it high */ + gpio_direction_output(DSMG600_PO_GPIO, 1); } /* This is used to make sure the power-button pusher is serious. The button @@ -202,7 +200,7 @@ static void dsmg600_power_handler(unsigned long data) ctrl_alt_del(); /* Change the state of the power LED to "blink" */ - gpio_line_set(DSMG600_LED_PWR_GPIO, IXP4XX_GPIO_LOW); + gpio_set_value(DSMG600_LED_PWR_GPIO, 0); } else { power_button_countdown = PBUTTON_HOLDDOWN_COUNT; } @@ -252,6 +250,7 @@ static void __init dsmg600_init(void) pm_power_off = dsmg600_power_off; + gpio_request(DSMG600_RB_GPIO, "reset button"); if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler, IRQF_DISABLED | IRQF_TRIGGER_LOW, "DSM-G600 reset button", NULL) < 0) { @@ -266,7 +265,10 @@ static void __init dsmg600_init(void) */ /* Make sure that the power button GPIO is set up as an input */ - gpio_line_config(DSMG600_PB_GPIO, IXP4XX_GPIO_IN); + gpio_request(DSMG600_PB_GPIO, "power button"); + gpio_direction_input(DSMG600_PB_GPIO); + /* Request poweroff GPIO line */ + gpio_request(DSMG600_PO_GPIO, "power off button"); /* Set the initial value for the power button IRQ handler */ power_button_countdown = PBUTTON_HOLDDOWN_COUNT; diff --git a/arch/arm/mach-ixp4xx/ixdp425-setup.c b/arch/arm/mach-ixp4xx/ixdp425-setup.c index 22d688b..e7b8bef 100644 --- a/arch/arm/mach-ixp4xx/ixdp425-setup.c +++ b/arch/arm/mach-ixp4xx/ixdp425-setup.c @@ -20,6 +20,7 @@ #include <linux/mtd/nand.h> #include <linux/mtd/partitions.h> #include <linux/delay.h> +#include <linux/gpio.h> #include <asm/types.h> #include <asm/setup.h> #include <asm/memory.h> @@ -80,10 +81,10 @@ ixdp425_flash_nand_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl) if (ctrl & NAND_CTRL_CHANGE) { if (ctrl & NAND_NCE) { - gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_LOW); + gpio_set_value(IXDP425_NAND_NCE_PIN, 0); udelay(5); } else - gpio_line_set(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_HIGH); + gpio_set_value(IXDP425_NAND_NCE_PIN, 1); offset = (ctrl & NAND_CLE) ? IXDP425_NAND_CMD_BYTE : 0; offset |= (ctrl & NAND_ALE) ? IXDP425_NAND_ADDR_BYTE : 0; @@ -227,7 +228,8 @@ static void __init ixdp425_init(void) ixdp425_flash_nand_resource.start = IXP4XX_EXP_BUS_BASE(3), ixdp425_flash_nand_resource.end = IXP4XX_EXP_BUS_BASE(3) + 0x10 - 1; - gpio_line_config(IXDP425_NAND_NCE_PIN, IXP4XX_GPIO_OUT); + gpio_request(IXDP425_NAND_NCE_PIN, "NAND NCE pin"); + gpio_direction_output(IXDP425_NAND_NCE_PIN, 0); /* Configure expansion bus for NAND Flash */ *IXP4XX_EXP_CS3 = IXP4XX_EXP_BUS_CS_EN | diff --git a/arch/arm/mach-ixp4xx/nas100d-setup.c b/arch/arm/mach-ixp4xx/nas100d-setup.c index ed667ce..04f723a 100644 --- a/arch/arm/mach-ixp4xx/nas100d-setup.c +++ b/arch/arm/mach-ixp4xx/nas100d-setup.c @@ -184,11 +184,8 @@ static void nas100d_power_off(void) { /* This causes the box to drop the power and go dead. */ - /* enable the pwr cntl gpio */ - gpio_line_config(NAS100D_PO_GPIO, IXP4XX_GPIO_OUT); - - /* do the deed */ - gpio_line_set(NAS100D_PO_GPIO, IXP4XX_GPIO_HIGH); + /* enable the pwr cntl gpio and assert power off */ + gpio_direction_output(NAS100D_PO_GPIO, 1); } /* This is used to make sure the power-button pusher is serious. The button @@ -225,7 +222,7 @@ static void nas100d_power_handler(unsigned long data) ctrl_alt_del(); /* Change the state of the power LED to "blink" */ - gpio_line_set(NAS100D_LED_PWR_GPIO, IXP4XX_GPIO_LOW); + gpio_set_value(NAS100D_LED_PWR_GPIO, 0); } else { power_button_countdown = PBUTTON_HOLDDOWN_COUNT; } @@ -283,8 +280,12 @@ static void __init nas100d_init(void) * have to poll it with a kernel timer. */ + /* Request the power off GPIO */ + gpio_request(NAS100D_PO_GPIO, "power off"); + /* Make sure that the power button GPIO is set up as an input */ - gpio_line_config(NAS100D_PB_GPIO, IXP4XX_GPIO_IN); + gpio_request(NAS100D_PB_GPIO, "power button"); + gpio_direction_input(NAS100D_PB_GPIO); /* Set the initial value for the power button IRQ handler */ power_button_countdown = PBUTTON_HOLDDOWN_COUNT; diff --git a/arch/arm/mach-ixp4xx/nslu2-setup.c b/arch/arm/mach-ixp4xx/nslu2-setup.c index 7e55236..c8c13df 100644 --- a/arch/arm/mach-ixp4xx/nslu2-setup.c +++ b/arch/arm/mach-ixp4xx/nslu2-setup.c @@ -197,11 +197,8 @@ static void nslu2_power_off(void) { /* This causes the box to drop the power and go dead. */ - /* enable the pwr cntl gpio */ - gpio_line_config(NSLU2_PO_GPIO, IXP4XX_GPIO_OUT); - - /* do the deed */ - gpio_line_set(NSLU2_PO_GPIO, IXP4XX_GPIO_HIGH); + /* enable the pwr cntl gpio and assert power off */ + gpio_direction_output(NSLU2_PO_GPIO, 1); } static irqreturn_t nslu2_power_handler(int irq, void *dev_id) @@ -273,6 +270,9 @@ static void __init nslu2_init(void) gpio_to_irq(NSLU2_PB_GPIO)); } + /* Request the power off GPIO */ + gpio_request(NSLU2_PO_GPIO, "power off"); + /* * Map in a portion of the flash and read the MAC address. * Since it is stored in BE in the flash itself, we need to -- 1.8.3.1 -- To unsubscribe from this list: send the line "unsubscribe linux-gpio" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
