On Mon, Dec 1, 2014 at 9:09 PM, <[email protected]> wrote:
> From: Kamlakant Patel <[email protected]>
>
> This is a brief documentation on how to use GPIO Generic
> library for memory-mapped GPIO controllers.
>
> Signed-off-by: Kamlakant Patel <[email protected]>
> ---
> Documentation/gpio/driver.txt | 50
> +++++++++++++++++++++++++++++++++++++++++++
> 1 file changed, 50 insertions(+)
Yum, more doc!
>
> diff --git a/Documentation/gpio/driver.txt b/Documentation/gpio/driver.txt
> index 31e0b5d..563abea 100644
> --- a/Documentation/gpio/driver.txt
> +++ b/Documentation/gpio/driver.txt
> @@ -190,3 +190,53 @@ gpiochip_free_own_desc().
> These functions must be used with care since they do not affect module use
> count. Do not use the functions to request gpio descriptors not owned by the
> calling driver.
> +
> +
> +Generic driver for memory-mapped GPIO controllers
> +-------------------------------------------------
> +The GPIO generic library provides support for basic platform_device
> +memory-mapped GPIO controllers, which can be accessed by selecting Kconfig
> +symbol GPIO_GENERIC and using library functions provided by GPIO generic
> +driver (see drivers/gpio/gpio-generic.c).
> +The simplest form of a GPIO controller that the driver support is just a
s/support/supports
> +single "data" register, where GPIO state can be read and/or written.
> +
> +The driver can be registered using "basic-mmio-gpio" or for big-endian
> +notation support use "basic-mmio-gpio-be". The code will configure gpio_chip
Using where? You should say that this is for the platform device name.
> +and issue gpiochip_add().
> +
> +The driver supports:
> +- 8/16/32/64 bits registers. The number of GPIOs is determined by the width
> of
> + the registers.
> +- GPIO controllers with clear/set registers.
> +- GPIO controllers with a single "data" register.
> +- Big endian bits/GPIOs ordering.
Maybe add a sentence indicating that these settings are defined in the
drivers using named memory resources.
> +
> +For setting GPIO's there are three supported configurations:
> +- single input/output register resource (named "dat").
This resource seems to be mandatory - please make sure you mention this fact.
> +- set/clear pair (named "set" and "clr").
> +- single output register resource and single input resource ("set" and dat").
> +
> +For setting the GPIO direction, there are three supported configurations:
> +- simple bidirection GPIO that requires no configuration.
s/bidirection/bidirectional maybe?
> +- an output direction register (named "dirout") where a 1 bit indicates the
> + GPIO is an output.
> +- an input direction register (named "dirin") where a 1 bit indicates the
> GPIO
> + is an input.
> +
> +It is possible to use only parts of GPIO generic library. Each GPIO
> controller
> +using GPIO generic library needs to include the following header.
> +
> + #include <linux/basic_mmio_gpio.h>
> +
> +Use bgpio_init to configure gpio_chip and bgpio_remove to remove the
> controller.
> +int bgpio_init(struct bgpio_chip *bgc, struct device *dev,
> + unsigned long sz, void __iomem *dat, void __iomem *set,
> + void __iomem *clr, void __iomem *dirout, void __iomem *dirin,
> + unsigned long flags);
If you put the prototype for bgpio_init(), please also put the one of
bgpio_remove()...
> +
> +The "flag" parameter can be following depending on controller configuration:
> +BGPIOF_BIG_ENDIAN BIT(0)
> +BGPIOF_UNREADABLE_REG_SET BIT(1) /* reg_set is unreadable */
> +BGPIOF_UNREADABLE_REG_DIR BIT(2) /* reg_dir is unreadable */
> +BGPIOF_BIG_ENDIAN_BYTE_ORDER BIT(3)
Right now this documentation is a little bit confusing. Basically
there are two ways to use this driver:
1) Name your platform device ""basic-mmio-gpio" or
"basic-mmio-gpio-be", set the right named memory resources to specify
the desired configuration, and let bgpio_pdev_probe() do all the work.
2) Allocate a bgpio_chip yourself, call bgpio_init() on it and its
resources, and finally invoke gpiochip_add() yourself.
These two different ways of doing kind of seem to be mixed together.
Can you try to highlight the fact that these are alternatives?
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
