On Fri, Nov 20, 2015 at 03:29:52AM +0200, Vladimir Zapolskiy wrote:
> For the purpose of better description of NXP LPC32xx GPIO controller
> hardware in device tree format, extend the existing description with
> device tree subnodes, which represent 6 GPIO banks within the
> controller.
>
> Note, client interface to the GPIO controller is untouched.
>
> Signed-off-by: Vladimir Zapolskiy <v...@mleia.com>
> ---
> .../devicetree/bindings/gpio/gpio_lpc32xx.txt | 121
> ++++++++++++++++++++-
> 1 file changed, 120 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt
> b/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt
> index 4981936..d2da63c 100644
> --- a/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt
> +++ b/Documentation/devicetree/bindings/gpio/gpio_lpc32xx.txt
> @@ -15,7 +15,43 @@ Required properties:
> 2) pin number
> 3) optional parameters:
> - bit 0 specifies polarity (0 for normal, 1 for inverted)
> -- reg: Index of the GPIO group
> +- #address-cells: should be 2, which stands for GPIO bank id and
> + physical base address of this GPIO bank.
Now you need special code to do address translation. I'd really think
twice about doing this.
Why do you need the bank number?
> +- #size-cells: should be 1, total size of GPIO bank registers.
> +
> +The NXP LPC32xx SoC GPIO controller device node must contain a list
> +of device nodes representing GPIO banks and their descriptions.
> +
> +The format of subnodes should follow the description below.
> +
> +Required properties:
> +- reg: should contain 3 integer values:
> + 1) GPIO bank id from 0 to 5,
> + 2) physical base address of this GPIO bank,
> + 3) total size of the GPIO bank registers.
> +
> +Optional properties:
> +- gpio-bank-name: human readable name of a GPIO bank,
> +- gpio-no-output-state: property of P2 bank, which has special,
> + mapping of its control registers,
> +- gpio-offset: property of P3/GPIO bank, offset of bits representing
> + GPIO lines in output and direction registers,
Seems like nr-gpios should have been a mask instead...
> +- gpios: number of GPIO lines per GPIO bank, if this property is
> + omitted, then gpio-input-mask must be present,
"gpios" is already the property name for the client interface.
> +- gpio-input-mask: should contain two bitmasks, the first bitmask is
> + the mapping of GPIO lines to input status register, the second
> + bitmask should be a subset of the first bitmask and it represents
> + input GPIO lines, which may serve as an interrupt source,
> + if gpio-input-mask roperty is omitted, gpios property should be
> + present,
> +- interrupts: list of parent interrupts mapped to input GPIO lines,
> +- interrupts-extended: list of parent interrupts mapped to input GPIO
> + lines, used if parent interrupts are provided by more than one
> + interrupt controller, this option is used by GPI bank,
> +- interrupt-controller: indicates that GPIO bank may serve as an
> + interrupt controller,
> +- #interrupt-cells: if interrupt-controller property is present,
> + it should be 2, interrupt id and its flags.
>
> Example:
>
> @@ -24,6 +60,89 @@ Example:
> reg = <0x40028000 0x1000>;
> gpio-controller;
> #gpio-cells = <3>; /* bank, pin, flags */
Can't bank and pin be encoded into one cell as the gpio core binding
suggests.
> +
> + ranges = <0 0x0 0x40028000 0x00001000>,
> + <1 0x0 0x40028000 0x00001000>,
> + <2 0x0 0x40028000 0x00001000>,
> + <3 0x0 0x40028000 0x00001000>,
> + <4 0x0 0x40028000 0x00001000>,
> + <5 0x0 0x40028000 0x00001000>;
> + #address-cells = <2>;
> + #size-cells = <1>;
> +
> + gpio_p0: gpio-controller@0 {
> + reg = <0 0x40 0x1C>;
> + gpio-bank-name = "p0";
> + gpios = <8>;
> +
> + interrupt-parent = <&sic2>;
> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpio_p1: gpio-controller@1 {
> + reg = <1 0x60 0x1C>;
> + gpio-bank-name = "p1";
> + gpios = <24>;
> +
> + interrupt-parent = <&sic2>;
> + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
> + };
> +
> + gpio_p2: gpio-controller@2 {
> + reg = <2 0x10 0x18>;
> + gpio-bank-name = "p2";
> + gpios = <13>;
> + gpio-no-output-state;
> + };
> +
> + gpio_gpio: gpio-controller@3 {
> + reg = <3 0x00 0x1C>;
This overlaps with bank 2.
> + gpio-bank-name = "gpio";
> + gpio-offset = <25>;
> + gpio-input-mask = <0x01007c00>, <0x01007c00>;
> +
> + interrupt-parent = <&sic2>;
> + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>,
> + <1 IRQ_TYPE_LEVEL_HIGH>,
> + <2 IRQ_TYPE_LEVEL_HIGH>,
> + <3 IRQ_TYPE_LEVEL_HIGH>,
> + <4 IRQ_TYPE_LEVEL_HIGH>,
> + <5 IRQ_TYPE_LEVEL_HIGH>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpio_gpi: gpio-controller@4 {
> + reg = <4 0x00 0x04>;
> + gpio-bank-name = "gpi";
> + gpio-input-only;
> + gpio-input-mask = <0x1aff83ff>, <0x100803ff>;
> +
> + interrupts-extended =
> + <&sic2 22 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic2 23 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic2 24 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic2 25 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic2 26 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic2 27 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic2 28 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic2 15 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic2 9 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic2 10 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic2 11 IRQ_TYPE_LEVEL_HIGH>,
> + <&sic1 4 IRQ_TYPE_LEVEL_HIGH>;
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + };
> +
> + gpio_gpo: gpio-controller@5 {
> + reg = <5 0x00 0x10>;
> + gpio-bank-name = "gpo";
> + gpios = <24>;
> + gpio-output-only;
> + };
> };
>
> leds {
> --
> 2.1.4
>
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
