Hi,
I tried a crm_resource command.
Heartbeat stopped when I carried it out after the log of the error message
appeared.
crmd[4029]: **** ERROR: verify_stopped:Resource resource_* was active at
shutdown.
You may ignore this error if it is unmanaged.
I tried a command before stopping Heartbeat.
but, Heartbeat did not stop.
Will the crm_resouce command be no use unless I carry it out after error log
appeared?
Regards,
Hideo Yamauchi.
--- HIDEO YAMAUCHI <[EMAIL PROTECTED]> wrote:
> Hi,
>
> OK.
>
> I try crm_resouce.
> I discuss GUI in a mailing list again.
>
> Thank you.
>
> Hideo Yamauchi.
>
>
> --- Andrew Beekhof <[EMAIL PROTECTED]> wrote:
>
> >
> > On Nov 27, 2007, at 10:20 AM, HIDEO YAMAUCHI wrote:
> >
> > > Hi,
> > >
> > >> in this case the cluster can't stop the resource because the resource
> > >> isnt valid according to the RA (since you didnt add a parameter)
> > >> we tried to stop it and the RA reported failure.
> > >>
> > >> without stonith enabled there is nothing more the cluster can do
> > >
> > > In this case an operator does not have the choice except KILL.
> >
> > i guess you could repair the resource definition and then use
> > crm_resource -C
> > that should probably work
> >
> > > In GUI, is not the check of the required parameter necessary to
> > > prevent such a mistake?
> >
> > quite possibly
> >
> > /me is utterly ignorant of the gui and prefers it that way
> >
> > >
> > >
> > > http://www.gossamer-threads.com/lists/linuxha/dev/43184
> > >
> > > Regards,
> > > Hideo Yamauchi.
> > >
> > >
> > > --- Andrew Beekhof <[EMAIL PROTECTED]> wrote:
> > >
> > >>
> > >> On Nov 27, 2007, at 8:11 AM, HIDEO YAMAUCHI wrote:
> > >>
> > >>> Hi,
> > >>>
> > >>> I tested the addition of the resource from GUI.
> > >>> First cib.xml does not have the resource.
> > >>> I used the latest development edition.(Heartbeat-Dev-68a5c0c53078)
> > >>>
> > >>> I operated it in order of next.
> > >>>
> > >>> 1)I am connected to the DC node in GUI.
> > >>> 2)I add a FileSystem resource without appointing a parameter.
> > >>> 3)The FileSystem resource is displayed with unmanaged in GUI.
> > >>> 4)I stop service of Heartbeat.
> > >>>
> > >>> But, Heartbeat does not stop.
> > >>> The last following log appeared.
> > >>>
> > >>> ----------------------------------------------------------------
> > >>> crmd[4029]: 2007/11/27_16:00:26 info: do_shutdown: Terminating the
> > >>> tengine
> > >>> crmd[4029]: 2007/11/27_16:00:26 info: stop_subsystem: Sent -TERM to
> > >>> tengine: [4032]
> > >>> crmd[4029]: 2007/11/27_16:00:26 info: do_shutdown: Waiting for
> > >>> subsystems to exit
> > >>> crmd[4029]: 2007/11/27_16:00:26 info: do_shutdown: All subsystems
> > >>> stopped, continuing
> > >>> crmd[4029]: 2007/11/27_16:00:26 info: crmdManagedChildDied: Process
> > >>> tengine:[4032] exited (signal=0,
> > >>> exitcode=0)
> > >>> crmd[4029]: 2007/11/27_16:00:26 info: crmdManagedChildDied: Process
> > >>> pengine:[4033] exited (signal=0,
> > >>> exitcode=0)
> > >>> crmd[4029]: 2007/11/27_16:00:26 info: do_shutdown: All subsystems
> > >>> stopped, continuing
> > >>> crmd[4029]: 2007/11/27_16:00:26 ERROR: verify_stopped: Resource
> > >>> resource_ was active at shutdown. You
> > >>> may ignore this error if it is unmanaged.
> > >>> crmd[4029]: 2007/11/27_16:00:26 info: process_client_disconnect:
> > >>> Received HUP from tengine:[-1]
> > >>> crmd[4029]: 2007/11/27_16:00:26 info: process_client_disconnect:
> > >>> Received HUP from pengine:[-1]
> > >>> crmd[4029]: 2007/11/27_16:00:26 ERROR: verify_stopped: Resource
> > >>> resource_ was active at shutdown. You
> > >>> may ignore this error if it is unmanaged.
> > >>> crmd[4029]: 2007/11/27_16:05:06 ERROR: verify_stopped: Resource
> > >>> resource_ was active at shutdown. You
> > >>> may ignore this error if it is unmanaged.
> > >>> ----------------------------------------------------------------
> > >>>
> > >>>
> > >>> In the case of unmanaged, is there a right procedure to stop?
> > >>
> > >> in this case the cluster can't stop the resource because the resource
> > >> isnt valid according to the RA (since you didnt add a parameter)
> > >> we tried to stop it and the RA reported failure.
> > >>
> > >> without stonith enabled there is nothing more the cluster can do
> > >>
> > >>>
> > >>> Or is this bug?
> > >>>
> > >>> I attach a collection of hb_report result.
> > >>>
> > >>> Regards,
> > >>> Hideo Yamauchi.
> > >>>
> > >>>
> > >>> <report_Dev.tar.gz>_______________________________________________
> > >>> Linux-HA mailing list
> > >>> [email protected]
> > >>> http://lists.linux-ha.org/mailman/listinfo/linux-ha
> > >>> See also: http://linux-ha.org/ReportingProblems
> > >>
> > >> _______________________________________________
> > >> Linux-HA mailing list
> > >> [email protected]
> > >> http://lists.linux-ha.org/mailman/listinfo/linux-ha
> > >> See also: http://linux-ha.org/ReportingProblems
> > >>
> > >
> > > _______________________________________________
> > > Linux-HA mailing list
> > > [email protected]
> > > http://lists.linux-ha.org/mailman/listinfo/linux-ha
> > > See also: http://linux-ha.org/ReportingProblems
> >
> > _______________________________________________
> > Linux-HA mailing list
> > [email protected]
> > http://lists.linux-ha.org/mailman/listinfo/linux-ha
> > See also: http://linux-ha.org/ReportingProblems
> >
>
> _______________________________________________
> Linux-HA mailing list
> [email protected]
> http://lists.linux-ha.org/mailman/listinfo/linux-ha
> See also: http://linux-ha.org/ReportingProblems
>
_______________________________________________
Linux-HA mailing list
[email protected]
http://lists.linux-ha.org/mailman/listinfo/linux-ha
See also: http://linux-ha.org/ReportingProblems
