Affan Basalamah (96-018) wrote: > > hi there, > > I have a question about soundcard to be used as soundcard modem. I wonder > how can I use a ESS-based Plug and Play to play soundmodem in Linux, while > I can use it to play soundmodem in PC/Flexnet Win95. AFAIK, I have to use > the real, non-pnp Soundblaster card, which is too expensive for me, > compared to ESS-based soundcard. Should I run isapnp command or something, > and if I do that, will it run well ?? > > I can play soundmodem in Win95 by initializing ESSCFG.EXE dan ESSVOL.EXE > right before I run FLEXNET.EXE and other application. By using that > command, my ESS-based soundcard is running as Soundblaster compatible, > ready to be initialized by SMSBC.EXE... > > thanks, > Affan Basalamah Soundmodem works ok in Linux with ESS1868 and ESS1869 ! If yor BIOS not initialize the soundcard you must use ISAPNP. I attach the file /etc/isapnp.conf for ESS1869. You must run isapnp befor 'modprobe soundmodem' ( the soundmodem must be compiled as module) -- ################################################################### # Minta Adrian - YO3GIH phone: 04+092451899 # # mailto:[EMAIL PROTECTED] http://www.csit-sun.pub.ro/~gygy/ # ################################################################### # $Id: pnpdump.c,v 1.8 1997/01/14 21:05:35 fox Exp $ # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of this file format, see isapnp.conf(5) # # Compiler flags: -DREALTIME -DNEEDSETSCHEDULER # # Trying port address 0203 # Board 1 has serial identifier be ff ff ff ff 69 18 73 16 # (DEBUG) (READPORT 0x0203) (ISOLATE) (IDENTIFY *) # Card 1: (serial identifier be ff ff ff ff 69 18 73 16) # ESS1869 Serial No -1 [checksum be] # Version 1.0, Vendor version 1.0 # ANSI string -->ESS ES1869 Plug and Play AudioDrive<-- # # Logical device id ESS0006 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE ESS1869/-1 (LD 0 # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0800 # Maximum IO base address 0x0ff8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (BASE 0x0800)) # (ACT Y) )) # # Logical device id ESS1869 # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE ESS1869/-1 (LD 1 # Multiple choice time, choose one only ! # Start dependent functions: priority preferred # First DMA channel 1. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode (DMA 0 (CHANNEL 1)) # Next DMA channel 0 or 3. # 8 bit DMA only # Logical device is not a bus master # DMA may execute in count by byte mode # DMA may not execute in count by word mode # DMA channel speed in compatible mode (DMA 1 (CHANNEL 3)) # IRQ 5. # High true, edge sensitive interrupt (by default) (INT 0 (IRQ 5 (MODE +E))) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0220 # Maximum IO base address 0x0220 # IO base alignment 0 bytes # Number of IO addresses required: 16 (IO 0 (BASE 0x0220)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0388 # Maximum IO base address 0x0388 # IO base alignment 0 bytes # Number of IO addresses required: 4 (IO 1 (BASE 0x0388)) # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0330 # Maximum IO base address 0x0330 # IO base alignment 0 bytes # Number of IO addresses required: 2 (IO 2 (BASE 0x0330)) # End dependent functions (ACT Y) )) # End tag... Checksum 0x00 (OK)
