Linux-Hardware Digest #225, Volume #11 Fri, 10 Sep 99 18:13:35 EDT
Contents:
HELP: Need help identifying mystery card! ([EMAIL PROTECTED])
Re: DMA support (Peter Stein)
Linux support for HP 340CBi infrared printer ([EMAIL PROTECTED])
Re: CD burner suggestions? (Johan Kullstam)
Radio tuner cards ("Ashoka D. Polpitiya")
RedHat 6.0 Install Problem
Re: FREE EAST TIMOR!!! STOP THE KILLING!!! (James Knott)
Re: 13GB Hard Drive problems -- appears much smaller... ("William B. Cattell")
Re: Radio tuner cards (Greg Yantz)
Re: AMD K6-2/300 (Mike Frisch)
CD-R suggestions... (EKK)
Re: CD burner suggestions? (Johan Kullstam)
Re: AMD K6-2 (Mike Frisch)
Re: Need guidance with Scanner type (Geoff Blake)
Re: Modem Stupidity (John McKown)
HP-7570I CD-Writer+ and HP-3200C Flatbed Scanner (Habibi4me)
----------------------------------------------------------------------------
From: [EMAIL PROTECTED]
Crossposted-To:
comp.sys.ibm.pc.hardware.misc,comp.sys.ibm.pc.hardware.comm,it.comp.retrocomputing
Subject: HELP: Need help identifying mystery card!
Date: Fri, 10 Sep 1999 20:23:34 GMT
I've got a card that I'm having a great deal of trouble identifying. It
LOOKS like a weirdass SCSI card, but I *suspect* it is a multiport
Serial controller, otherwise known as an 'octopus'. A few things
suggest this, including the four AM8530H Serial controller chips on the
card.
What I really need however, is the documentation that goes with the
card.
I offer my gratitude, as well as bragging rights to the person who can
point me towards the docs for this card.
here are the particulars:
-16 Bit ISA card, full length.
-80 pin Dsub female connector.
-Identifying marks: "DBI A/N 30000674" and in another place "DBI A/N
30000624", "DBI P/N 30000622" and elsewhere on the card: "DBI P/N
30000672", "Made in USA".
-Other predominant Processor: N80C186 (1978).
-Four AMD AM8530H Serial controller Chips.
-Suspected Date of card manufacture: 1993.
-Origin of card: Unknown. Came in an assorted box of junk I bought for
$10. Although it appears to be 16 bit ISA, it may not actually be so.
I have heard of a hardware reference database that was very useful for
idenitfying obscure components, and had docs for them as well..
does anyone have access to this?
Best regards,
Dan.
Sent via Deja.com http://www.deja.com/
Share what you know. Learn what you don't.
------------------------------
From: [EMAIL PROTECTED] (Peter Stein)
Subject: Re: DMA support
Date: 10 Sep 1999 20:52:36 GMT
In article <[EMAIL PROTECTED]>,
martin <[EMAIL PROTECTED]> wrote:
>
>
>[EMAIL PROTECTED] wrote:
>
>> Hi,
>>
>> I would like to get DMA / UltraDMA to work...but just standard transfer
>> works
>> IMOHO the problem is that the kernel doesn't support my chipset...
>> Do newer kernels work with my motherboard? or did I do something wrong?
>> Any input regarding this matter is highly appreciated.
>>
>> My system:
>> Asus PA-B mainboard (uses the ALI Aladdin V chipset)
>> AMD K6-2 333Mhz
>> QUANTUM FIREBALL EX6.4A (supports at least DMA)
>>
>> dmesg prints out :
>> Linux version 2.2.5-15 ([EMAIL PROTECTED]) (gcc version
>> egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Mon Apr 19 22:21:09
>> EDT 1999
>> Detected 332760776 Hz processor.
>> Console: colour VGA+ 80x25
>> Calibrating delay loop... 663.55 BogoMIPS
>> Memory: 63080k/65472k available (996k kernel code, 412k reserved, 924k
>> data, 60k init)
>> VFS: Diskquotas version dquot_6.4.0 initialized
>> CPU: AMD AMD-K6(tm) 3D processor stepping 00
>> Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
>> Checking 'hlt' instruction... OK.
>> POSIX conformance testing by UNIFIX
>> PCI: PCI BIOS revision 2.10 entry at 0xf0560
>> PCI: Using configuration type 1
>> PCI: Probing PCI hardware
>> <snip>
>> apm: BIOS version 1.2 Flags 0x03 (Driver version 1.9)
>> Real Time Clock Driver v1.09
>> RAM disk driver initialized: 16 RAM disks of 4096K size
>> PCI_IDE: unknown IDE controller on PCI bus 00 device 78, VID=10b9,
>> DID=5229
>> PCI_IDE: not 100% native mode: will probe irqs later
>> PCI_IDE: simplex device: DMA disabled
>> ide0: PCI_IDE Bus-Master DMA disabled (BIOS)
>> PCI_IDE: simplex device: DMA disabled
>> ide1: PCI_IDE Bus-Master DMA disabled (BIOS)
>> hda: QUANTUM FIREBALL EX6.4A, ATA DISK drive
>> hdb: FX322M, ATAPI CDROM drive
>> ide2: ports already in use, skipping probe
>> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>> hda: QUANTUM FIREBALL EX6.4A, 6149MB w/418kB Cache, CHS=784/255/63
>> hdb: ATAPI 32X CD-ROM drive, 256kB Cache
>> Uniform CDROM driver Revision: 2.54
>> <snip>
>>
>> /proc/pci delivers:
>> PCI devices found:
>> Bus 0, device 0, function 0:
>> Host bridge: Acer Labs Unknown device (rev 4).
>> Vendor id=10b9. Device id=1541.
>> Slow devsel. Master Capable. Latency=64.
>> Non-prefetchable 32 bit memory at 0xe0000000 [0xe0000000].
>> Bus 0, device 1, function 0:
>> PCI bridge: Acer Labs Unknown device (rev 4).
>> Vendor id=10b9. Device id=5243.
>> Slow devsel. Master Capable. Latency=64.
>> Bus 0, device 3, function 0:
>> Bridge: Acer Labs Unknown device (rev 0).
>> Vendor id=10b9. Device id=7101.
>> Medium devsel. Fast back-to-back capable.
>> Bus 0, device 7, function 0:
>> ISA bridge: Acer Labs M1533 Aladdin IV (rev 195).
>> Medium devsel. Master Capable. No bursts.
>> <snip>
>> Bus 0, device 15, function 0:
>> IDE interface: Acer Labs M5229 TXpro (rev 193).
>> Medium devsel. Fast back-to-back capable. Master Capable.
>> Latency=32. Min Gnt=2.Max Lat=4.
>> I/O at 0xd800 [0xd801].
>>
>> and hdparm tells:
>> /dev/hda:
>>
>> Model=QUANTUM FIREBALL EX6.4A, FwRev=A0A.0400, SerialNo=27683203
>> Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
>> RawCHS=13328/15/63, TrkSize=32256, SectSize=21298, ECCbytes=4
>> BuffType=3(DualPortCache), BuffSize=418kB, MaxMultSect=16, MultSect=off
>> DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=2(fast)
>> CurCHS=784/255/63, CurSects=789577920, LBA=yes, LBAsects=12594960
>> tDMA={min:120,rec:120}, DMA modes: mword0 mword1 mword2
>> IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
>>
>> thanks in advance, sebastian
>>
>> Sent via Deja.com http://www.deja.com/
>> Share what you know. Learn what you don't.
>
>Hi, i'm having the same problem, and honestly i think it has to do with the
>Ali V Chipset, which uses the 1541-1543 integrated chip for both
>busmastering and agp port support. i don't think it has to do with bios
>settings, as the bios report screen identifies my drive correctly to be
>udma2. But i do think however, that under the current stable versions of the
>kernel (2.2.1 and up) it is still a problem to get udma66 going. i have
>heard of a solution to work around this under dos setting the busmaster to
>udma 33 but couldnt get any proper information on how to do this. any help
>on this would be appreciated, and as this is a chipset used quite a lot i
>think a lot of people would be grateful for it.
>
>thanks a bunch in adv.
>martin
The problem is worse than you think. Even udma33 doesn't work correctly
for the P5A-B running kernel 2.2.9. UDMA reads are fine, but UDMA writes
cause errors which result in the driver getting kicked into PIO mode.
I've wrestled with this for some time, but have not found one (even one
of the driver authors has this problem). Short of rewriting the driver
myself I don't know what else to do. The good news is that at least DMA
works correctly and that's a lot better than PIO.
Peter Stein
[EMAIL PROTECTED]
------------------------------
From: [EMAIL PROTECTED]
Subject: Linux support for HP 340CBi infrared printer
Date: Fri, 10 Sep 1999 20:45:43 GMT
I am thinking of buying a portable color inkjet printer. Ideally, this
printer would have no wires attached.
There are two such printers on the market. One is HP Deskjet 340CBi
which has a rechargalbe battery and an infrared port. I would love
to buy this printer, but I would first like to verify if this printer
works with linux and its infrared support. I am using RedHat 6.0 Linux.
The other printer that is quite appealing is the Brother MP 21 cdx.
This printer needs no battery or power cable. It draws its power from
a notebook computer through its PCMCIA slot. There is a cable between
the printer and the PCMCIA card. But no power cable. Again, does anyone
use this printer with linux? Are there drivers available for the
Brother PCMCIA card?
I need to purchase the printer in a hurry. I would appreciate a quick
response.
Thanks,
--Atul
============
Atul K. Chhabra Phone: (914) 644-2786
Senior Member of Technical Staff Email: [EMAIL PROTECTED]
Bell Atlantic Network Systems
Advanced Technology
500 Westchester Avenue
White Plains, NY 10604, USA
Sent via Deja.com http://www.deja.com/
Share what you know. Learn what you don't.
------------------------------
Subject: Re: CD burner suggestions?
From: Johan Kullstam <[EMAIL PROTECTED]>
Date: 10 Sep 1999 16:32:55 -0400
Bryan <Bryan@[EMAIL PROTECTED]> writes:
> Johan Kullstam <[EMAIL PROTECTED]> wrote:
>
> : put both reader and burner on the scsi bus. get either plextor or
> : yamaha burner and pretty much any scsi cd reader.
>
> no need to do this. why do you say this?
for reliability, scsi is the way to go. it's better to put the two
devices on the same scsi bus if they are going to feed data from one
to the other. this way there is less interference by routing through
the host.
--
J o h a n K u l l s t a m
[[EMAIL PROTECTED]]
Don't Fear the Penguin!
------------------------------
From: "Ashoka D. Polpitiya" <[EMAIL PROTECTED]>
Subject: Radio tuner cards
Date: Tue, 7 Sep 1999 23:50:24 -0500
Hi all,
Any suggessions on buying a radio card for my RH6 box (from where)?
Thanks,
-Ashoka
------------------------------
From: <[EMAIL PROTECTED]>
Subject: RedHat 6.0 Install Problem
Date: Fri, 10 Sep 1999 20:31:13 GMT
Just installed RedHat 6.0 without a problem. But, on the first reboot
(right after the install). I get the following errors:
scsi: aborting command due to timeout: pid 47, scsi1, channel 0, id 0, lun
0, Test Unit Ready 00 00 00 00 00
scsi: aborting command due to timeout: pid 47, scsi1, channel 0, id 0, lun
0, Test Unit Ready 00 00 00 00 00
My system:
Adaptec AHA3940UW(68pin model)
Pentium Pro dual processor board(440FX chipset)
1 CPU
96 MB RAM
Matrox Millenium Video Card(4MB)
Yamaha OPL3-SAX Sound Card
Adapter# ID Device
SCSI(0) id#0 IBM DCAS-32160W (2.1GB)
SCSI(0) id#1 IBM DCAS-32160W (2.1GB)
SCSI(0) id#2 QUANTUM FIREBALL_TM3200S (3.2GB)
SCSI(0) id#5 TOSHIBA CD-ROM XM-5701TA
The error seems to be referencing the 2nd adapter on the card, but I don't
have anything on the 2nd adapter.
This is confusing, it worked fine with RedHat 5.X.
What gives? I've re-installed RedHat several times.
Can anyone help?
Thanx,
Rodney
================== Posted via CNET Linux Help ==================
http://www.searchlinux.com
------------------------------
From: [EMAIL PROTECTED] (James Knott)
Crossposted-To: comp.os.linux.m68k,comp.os.linux.misc
Subject: Re: FREE EAST TIMOR!!! STOP THE KILLING!!!
Date: Fri, 10 Sep 1999 12:47:18 -0400
Reply-To: James Knott <[EMAIL PROTECTED]>
In article <[EMAIL PROTECTED]>, "Pedro RA" <[EMAIL PROTECTED]> wrote:
>Sorry to post off topic but this is EXTREMELY important!
>
>FREE EAST TIMOR NOW!
>STOP THE KILLING KNOW!
>
>Please take a look at the nearest
>internacional news broadcast.
>
>Remember KOSOVO, RUANDA,
>BOSNIA, CAMBODJA, KURDISTAN,
>or the HOLOCAUST. Or remember all
>of them. You may as well add
>EAST TIMOR to this list.
>
>DO SOMETHING!
>
>Do what ever you can.
>
>Better even:
>STOP SOMETHING THAT SHOULD NEVER HAVE HAPPENED!
>
> FREE EAST TIMOR
Let's all send them our old Linux CDs!!!
--
E-mail [EMAIL PROTECTED]
_________________________________________________________________________
The above opinions are my own and not those of ISM Corp., a subsidiary of
IBM Canada Ltd.
------------------------------
From: "William B. Cattell" <[EMAIL PROTECTED]>
Reply-To: [EMAIL PROTECTED]
Subject: Re: 13GB Hard Drive problems -- appears much smaller...
Date: Fri, 10 Sep 1999 16:57:30 GMT
Jesse Hughes wrote:
>
> I purchased a 13GB Western Digital hard drive and partitioned it for Linux
> (only). I used an old distribution set up disk, but I think it was 2.0
> kernel or so (Slackware 3.0 disk, perhaps?). Everything seemed to go
> well.
>
> I upgraded to Slackware 4.0 and then put in a 2.2.10 kernel. It took me a
> while, but I finally noticed that I'm missing part of my hard drive.
> Here's the output of df -h:
> Filesystem Size Used Avail Capacity Mounted on
> /dev/hda1 6.7G 3.0G 3.3G 47% /
> /dev/hda2 3.3G 19M 3.1G 1% /home
>
> Here's the output of fdisk with a warning and then the output of p.
>
> bash# fdisk
> Using /dev/hda as default device!
> The number of cylinders for this disk is set to 1582.
> There is nothing wrong with that, but this is larger than 1024,
> and could in certain setups cause problems with:
> 1) software that runs at boot time (e.g., LILO)
> 2) booting and partitioning software from other OSs
> (e.g., DOS FDISK, OS/2 FDISK)
> Command (m for help): p
> Disk /dev/hda: 255 heads, 63 sectors, 1582 cylinders
> Units = cylinders of 16065 * 512 bytes
> Device Boot Start End Blocks Id System
> /dev/hda1 1 1000 8032468+ 83 Linux native
> /dev/hda2 1001 1500 4016250 83 Linux native
> /dev/hda3 1501 1582 658665 82 Linux swap
>
> Where's the rest of me? Or my disk?
>
> (And, YES, I know that's a stupid size for a swap partition. My brain is
> the size of a turnip, but not as intelligent.)
>
> By the way, I also received error messages whenever I tried to run setup
> -- the messages were:
> Mount table corrupt. Reboot machine and run setup again.
> I'm sure now that these are related to my other problems.
>
> Any help would be appreciated. I realize that I'm going to have to
> reinstall everything to fix this problem, which is painful, but before I
> do anything, I'd like to be convinced there is a solution.
>
> Thanks. Please send a courtesy email copy with any help.
>
> > Jesse
Jesse - I recenty put a 13Gb IDE in my system and partitioned it as such...
/dev/hdd2 4.0G 49M 3.7G 1% /var
/dev/hdd1 7.7G 5.1G 2.2G 70% /backup
The number of cylinders for this disk is set to 25228.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): p
Disk /dev/hdd: 16 heads, 63 sectors, 25228 cylinders
Units = cylinders of 1008 * 512 bytes
Device Boot Start End Blocks Id System
/dev/hdd1 1 16645 8389079+ 83 Linux
/dev/hdd2 16646 25228 4325832 83 Linux
Disk mfr's always tell you the total capacity of a drive if there were no
'OS overhead'. Their documentation always includes a caveat to the effect
that "based on the OS used you may have less diskspace than advertised."
My guess is also that the way your system BIOS defines the drive comes into
play. I have an FIC 2013 (excellent board BTW) with an Award BIOS. In
there I can define the drive several different ways. I've chosen to use
LBA mode so it does some of the translation for me. FWIW.
Bill
--
==============================================================
http://members.home.com/wcattell
==============================================================
Park not thy Harley in the darkness of thine garage, that it
may collect dust for want of being oft ridden. Ride thy Harley
with thy brethren, and rejoice in the spirit of the road.
==============================================================
------------------------------
From: Greg Yantz <[EMAIL PROTECTED]>
Subject: Re: Radio tuner cards
Date: 10 Sep 1999 17:53:47 -0400
"Ashoka D. Polpitiya" <[EMAIL PROTECTED]> writes:
> Hi all,
> Any suggessions on buying a radio card for my RH6 box (from where)?
I can't think of any radio-only cards, but the WinTV TV tuner card
line from Hauppaugge includes a model with an FM tuner. I have
one- it works in both Linux and Windows. HTH.
-Greg
------------------------------
From: [EMAIL PROTECTED] (Mike Frisch)
Subject: Re: AMD K6-2/300
Date: 10 Sep 1999 11:55:24 GMT
On 10 Sep 1999 09:26:25 GMT, Jaakko Heikkila <[EMAIL PROTECTED]> wrote:
>is manufactured if its date code is AFR? Is it possible I have a faulty K6?
Highly unlikely if Windows runs fine (as you stated in your message).
Mike.
--
======================================================================
Mike Frisch Email: [EMAIL PROTECTED]
Northstar Technologies WWW: http://saturn.tlug.org/~mfrisch
Newmarket, Ontario, CANADA
======================================================================
------------------------------
From: EKK <[EMAIL PROTECTED]>
Subject: CD-R suggestions...
Date: Fri, 10 Sep 1999 04:53:29 -0700
I've seen a very helpful message about how to install a CD-R.
Has anybody any suggestions on a good one to install?
(i.e. manufacturer name and model #)
Is the Ricoh 6x4x24 MP7060A currently supported?
(I've seen a list of supported CD-Rs at xcdroast site, but seems
old...)
Thank you,
AG
--
Alessandro Giachino, Software Engineer
EKK Inc.
2065 West Maple C309 tel. 248-624-9957
Walled Lake MI 48390 fax. 248-624-7158
_____________________________________________
http://www.ekkinc.com
------------------------------
Subject: Re: CD burner suggestions?
From: Johan Kullstam <[EMAIL PROTECTED]>
Date: 10 Sep 1999 12:01:28 -0400
"Rick Carlson" <[EMAIL PROTECTED]> writes:
> I want to use re-writeable CD's for software backups.
> I also want to be able to create installable CD's for software distribution.
> Has anyone had experience with either of these operations?
> I would like to buy a reliable CD burner that supports all current CD media.
> Speed is not an issue, but reliability is (no 'coasters', please).
for maximum reliability get scsi. a fast/narrow scsi is fine for
periferals.
cheap cards like tekram dc-390 are out there (the f version is
overkill for this application. scsi hard drives and uw u2w adapters
are pricey.)
put both reader and burner on the scsi bus. get either plextor or
yamaha burner and pretty much any scsi cd reader.
fwiw you can use your scsi adapter for a scanner too. from what i
gather, scsi is pretty much a requirement for linux scanner action.
--
J o h a n K u l l s t a m
[[EMAIL PROTECTED]]
Don't Fear the Penguin!
------------------------------
From: [EMAIL PROTECTED] (Mike Frisch)
Subject: Re: AMD K6-2
Date: 10 Sep 1999 16:50:02 GMT
On Fri, 10 Sep 1999 11:01:33 -0500, Swami Chandrasekaran
<[EMAIL PROTECTED]> wrote:
>I'm planning to buy a new computer with AMD-K6-2 processor (400Mhz). Is
>it compatible with RH 6.0? How is the performance and possible troubles
>I could come across.
Yes, it's compatible with Linux. It'll feature near-Pentium 400
performance and there should be absolutely no compatibility issues with
the CPU itself. Lots of people use K6-2 CPUs with Linux, myself included.
Mike.
--
======================================================================
Mike Frisch Email: [EMAIL PROTECTED]
Northstar Technologies WWW: http://saturn.tlug.org/~mfrisch
Newmarket, Ontario, CANADA
======================================================================
------------------------------
From: [EMAIL PROTECTED] (Geoff Blake)
Crossposted-To: uk.comp.os.linux
Subject: Re: Need guidance with Scanner type
Date: Fri, 10 Sep 1999 20:17:47 GMT
Reply-To: [EMAIL PROTECTED]
Norman Elliott ([EMAIL PROTECTED]) wrote:
: Peter Hill wrote:
: > Hi all
: >
: > I know I need a scanner with a SCSI interface to use it with Linux but
: > other than that I don't know what else to look for. I am going to use it
: > with either an Adaptec 1542 or a Future Domain 950 or a Tekram 390U.
: >
: > I am considering either a UMAX 1220S or a Mustek Scanexpresss 12000SP.
: > Does anyone have any comments about either, or any recommendations ?
: >
: > I suspect that there is very little to choose between the UMAX or Mustek
: > or any other scanner at this price (�100 - �150), am right ?
: >
: > TIA -
: >
: > Peter
: > --
: > Peter Hill
: I have a Mustek ScaExpress 6000SP which works fine with a
: Side 2930U PCI SCSI Adapter.
I have a Mustek 12000SP (sadly running under W95) which has produced
excellent results. I have only used it with the (brain dead) DTC card it was
supplied with. I haven't used it on any of the Linux boxes here as I don't
have any spare scsi ports (it's amazing how many HDD's you can get in a full
tower!) but will do eventually as I have acquired some more scsi cards.
However, I have heard that it doesn't implement the scsi disconnect function
which implies (does it?) that it will hog the scsi bus and slow the system
down somewhat.
Geoff
--
Geoff Blake geoff (at) palaemon . demon . co . uk linux 2.0.36
Chelmsford g8gnz @ g8gnz . ampr . org sparc - i586
Please, only use the .ampr.org address if you know what you are doing
Intel create faster processors - Microsoft create slower processes
------------------------------
From: [EMAIL PROTECTED] (John McKown)
Subject: Re: Modem Stupidity
Date: 10 Sep 1999 00:58:10 GMT
On Thu, 09 Sep 1999 15:16:41 -0500, Mike Heien <[EMAIL PROTECTED]> wrote:
>This is probably going to induce sighing and laughter and several choice
>names thrown in my direction but I must ask anyway.
[big snip]
On my system, the modem is on COM2: (in DOS-Speak). In Linux-speak, that is
/dev/ttyS1. I'll bet that your modem is still OK, but not where it used to
be. So what I'd do is the following:
cd /dev
ls -l modem
This should show modem as a symlink to either ttyS0 (COM1:) or ttyS1 (COM2:).
You need to "find" your modem. So I'd do an "rm modem". Then do a
"ln -s ttyS0 modem". Now try to talk to the modem. If it works, stop. If it
doesn't work, then "rm modem" again. Now "ln -s ttyS1 modem". Try your test.
Work? Good. No? "rm modem", then "ln -s ttyS2 modem". Try again. Work? stop.
No? "rm modem", then "ln -s ttyS3 modem". Try again. Work? stop! NO? bitch
and moan because I can't see that that would be possible!
Basically, you're linking the /dev/modem device to the serial ports in order.
Then check to see if it works (I use minicom). I just did this on my system.
When I did the "ln -s ttyS0 modem", then minicom could not talk to the modem.
I just entered an "AT" command to get the "OK" response - which I didn't!
When I did the "ln -s ttyS1 modem" (which is where the modem really is),
then minicom could initialize the modem and I got a response to the "AT"
that I typed in.
Brute force, but it should work.
John
------------------------------
From: Habibi4me <[EMAIL PROTECTED]>
Subject: HP-7570I CD-Writer+ and HP-3200C Flatbed Scanner
Date: Fri, 10 Sep 1999 17:32:56 -0400
Hi,
I checked the CD-Writing HOWTO only found the support for an HP
CD-Writer 7500+ and am wondering if the HP-7570I CD-Writer+ is supporter
under Linux. If so, how well is the support? Will I be able to burn an
audio CD as well as dupplicate an iso9660 CD?
On the other hand, I will like to know if the HP-3200c flatbed scanner
is supported under Linux. If so, what software do I need to run in oder
to use this HP-3200c scanner?
TIA.
--
[EMAIL PROTECTED]
PS. Remove "4m" from e-mail address to enable reply.
------------------------------
** FOR YOUR REFERENCE **
The service address, to which questions about the list itself and requests
to be added to or deleted from it should be directed, is:
Internet: [EMAIL PROTECTED]
You can send mail to the entire list (and comp.os.linux.hardware) via:
Internet: [EMAIL PROTECTED]
Linux may be obtained via one of these FTP sites:
ftp.funet.fi pub/Linux
tsx-11.mit.edu pub/linux
sunsite.unc.edu pub/Linux
End of Linux-Hardware Digest
******************************
