On Sun, 4 Dec 2016 20:55:29 -0800, Guenter Roeck wrote:
> Fix overflows seen when writing large values into voltage limit,
> temperature limit, temperature offset, and DAC attributes.
>
> Overflows are seen due to unbound multiplications and additions.
>
> Signed-off-by: Guenter Roeck <[email protected]>
> ---
> drivers/hwmon/adm1026.c | 26 +++++++++++++++++---------
> 1 file changed, 17 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/hwmon/adm1026.c b/drivers/hwmon/adm1026.c
> index e67b9a50ac7c..b2a5d9e5c590 100644
> --- a/drivers/hwmon/adm1026.c
> +++ b/drivers/hwmon/adm1026.c
> @@ -197,8 +197,9 @@ static int adm1026_scaling[] = { /* .001 Volts */
> };
> #define NEG12_OFFSET 16000
> #define SCALE(val, from, to) (((val)*(to) + ((from)/2))/(from))
> -#define INS_TO_REG(n, val) (clamp_val(SCALE(val, adm1026_scaling[n], 192),\
> - 0, 255))
> +#define INS_TO_REG(n, val) \
> + SCALE(clamp_val(val, 0, 255 * adm1026_scaling[n] / 192), \
> + adm1026_scaling[n], 192)
> #define INS_FROM_REG(n, val) (SCALE(val, 192, adm1026_scaling[n]))
>
> /*
> @@ -215,11 +216,11 @@ static int adm1026_scaling[] = { /* .001 Volts */
> #define DIV_TO_REG(val) ((val) >= 8 ? 3 : (val) >= 4 ? 2 : (val) >= 2 ? 1 :
> 0)
>
> /* Temperature is reported in 1 degC increments */
> -#define TEMP_TO_REG(val) (clamp_val(((val) + ((val) < 0 ? -500 : 500)) \
> - / 1000, -127, 127))
> +#define TEMP_TO_REG(val) DIV_ROUND_CLOSEST(clamp_val(val, -128000, 127000), \
> + 1000)
> #define TEMP_FROM_REG(val) ((val) * 1000)
> -#define OFFSET_TO_REG(val) (clamp_val(((val) + ((val) < 0 ? -500 : 500)) \
> - / 1000, -127, 127))
> +#define OFFSET_TO_REG(val) DIV_ROUND_CLOSEST(clamp_val(val, -128000,
> 127000), \
> + 1000)
Sorry for nitpicking but the original code had -127 °C as the negative
limit. You are changing it to -128 °C without a justification. If it
matters, it should be at least documented in the commit message. If
not, it should be left as it was.
> #define OFFSET_FROM_REG(val) ((val) * 1000)
>
> #define PWM_TO_REG(val) (clamp_val(val, 0, 255))
> @@ -233,7 +234,8 @@ static int adm1026_scaling[] = { /* .001 Volts */
> * indicates that the DAC could be used to drive the fans, but in our
> * example board (Arima HDAMA) it isn't connected to the fans at all.
> */
> -#define DAC_TO_REG(val) (clamp_val(((((val) * 255) + 500) / 2500), 0, 255))
> +#define DAC_TO_REG(val) DIV_ROUND_CLOSEST(clamp_val(val, 0, 2500) * 255, \
> + 2500)
> #define DAC_FROM_REG(val) (((val) * 2500) / 255)
>
> /*
> @@ -593,7 +595,10 @@ static ssize_t set_in16_min(struct device *dev, struct
> device_attribute *attr,
> return err;
>
> mutex_lock(&data->update_lock);
> - data->in_min[16] = INS_TO_REG(16, val + NEG12_OFFSET);
> + data->in_min[16] = INS_TO_REG(16,
> + clamp_val(val, INT_MIN,
> + INT_MAX - NEG12_OFFSET) +
> + NEG12_OFFSET);
> adm1026_write_value(client, ADM1026_REG_IN_MIN[16], data->in_min[16]);
> mutex_unlock(&data->update_lock);
> return count;
> @@ -618,7 +623,10 @@ static ssize_t set_in16_max(struct device *dev, struct
> device_attribute *attr,
> return err;
>
> mutex_lock(&data->update_lock);
> - data->in_max[16] = INS_TO_REG(16, val+NEG12_OFFSET);
> + data->in_max[16] = INS_TO_REG(16,
> + clamp_val(val, INT_MIN,
> + INT_MAX - NEG12_OFFSET) +
> + NEG12_OFFSET);
> adm1026_write_value(client, ADM1026_REG_IN_MAX[16], data->in_max[16]);
> mutex_unlock(&data->update_lock);
> return count;
On these code paths, you end up calling clamp_val() twice. This could
certainly be avoided, but I'm too lazy to do the math ;-)
--
Jean Delvare
SUSE L3 Support
--
To unsubscribe from this list: send the line "unsubscribe linux-hwmon" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
