Hi Joel,

On 4/11/2018 4:52 AM, Joel Stanley wrote:
On 11 April 2018 at 04:02, Jae Hyun Yoo <jae.hyun....@linux.intel.com> wrote:
This commit adds a dt-bindings document of PECI adapter driver for Aspeed

We try to capitalise ASPEED.


Got it. Will capitalize all Aspeed words.

AST24xx/25xx SoCs.
---
  .../devicetree/bindings/peci/peci-aspeed.txt       | 60 ++++++++++++++++++++++
  1 file changed, 60 insertions(+)
  create mode 100644 Documentation/devicetree/bindings/peci/peci-aspeed.txt

diff --git a/Documentation/devicetree/bindings/peci/peci-aspeed.txt 
b/Documentation/devicetree/bindings/peci/peci-aspeed.txt
new file mode 100644
index 000000000000..4598bb8c20fa
--- /dev/null
+++ b/Documentation/devicetree/bindings/peci/peci-aspeed.txt
@@ -0,0 +1,60 @@
+Device tree configuration for PECI buses on the AST24XX and AST25XX SoCs.
+
+Required properties:
+- compatible        : Should be "aspeed,ast2400-peci" or "aspeed,ast2500-peci"
+                     - aspeed,ast2400-peci: Aspeed AST2400 family PECI
+                                            controller
+                     - aspeed,ast2500-peci: Aspeed AST2500 family PECI
+                                            controller
+- reg               : Should contain PECI controller registers location and
+                     length.
+- #address-cells    : Should be <1>.
+- #size-cells       : Should be <0>.
+- interrupts        : Should contain PECI controller interrupt.
+- clocks            : Should contain clock source for PECI controller.
+                     Should reference clkin.

Are you sure that this is driven by clkin? Most peripherals on the
Aspeed are attached to the apb, so should reference that clock.


According to the datasheet, PECI controller module is attached to apb but its clock source is the 24MHz external clock.

+- clock_frequency   : Should contain the operation frequency of PECI controller
+                     in units of Hz.
+                     187500 ~ 24000000

Can you explain why you need both the parent clock and this frequency
to be specified?


Based on this setting, driver code makes clock divisor value to set operation clock of PECI controller which is adjustable.

+
+Optional properties:
+- msg-timing-nego   : Message timing negotiation period. This value will

Perhaps msg-timing-period? Or just msg-timing?


Will use msg-timing instead.

+                     determine the period of message timing negotiation to be
+                     issued by PECI controller. The unit of the programmed
+                     value is four times of PECI clock period.
+                     0 ~ 255 (default: 1)
+- addr-timing-nego  : Address timing negotiation period. This value will
+                     determine the period of address timing negotiation to be
+                     issued by PECI controller. The unit of the programmed
+                     value is four times of PECI clock period.
+                     0 ~ 255 (default: 1)
+- rd-sampling-point : Read sampling point selection. The whole period of a bit
+                     time will be divided into 16 time frames. This value will
+                     determine the time frame in which the controller will
+                     sample PECI signal for data read back. Usually in the
+                     middle of a bit time is the best.
+                     0 ~ 15 (default: 8)
+- cmd_timeout_ms    : Command timeout in units of ms.
+                     1 ~ 60000 (default: 1000)
+
+Example:
+       peci: peci@1e78b000 {
+               compatible = "simple-bus";
+               #address-cells = <1>;
+               #size-cells = <1>;
+               ranges = <0x0 0x1e78b000 0x60>;
+
+               peci0: peci-bus@0 {
+                       compatible = "aspeed,ast2500-peci";
+                       reg = <0x0 0x60>;
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+                       interrupts = <15>;
+                       clocks = <&clk_clkin>;
+                       clock-frequency = <24000000>;
+                       msg-timing-nego = <1>;
+                       addr-timing-nego = <1>;
+                       rd-sampling-point = <8>;
+                       cmd-timeout-ms = <1000>;
+               };
+       };
--
2.16.2

--
To unsubscribe from this list: send the line "unsubscribe linux-hwmon" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to