On Tue, Oct 30, 2018 at 07:34:11PM +0000, Trent Piepho wrote:
> On Tue, 2018-10-30 at 18:00 +0100, Marco Felsch wrote:
> > On 18-10-30 06:13, Guenter Roeck wrote:
> > > On 10/30/18 3:47 AM, Marco Felsch wrote:
> > > >
> > hwmon-gpio-simple sounds ok for me.
> >
> > > The most difficult part of such a driver would probably be to define
> > > acceptable
> > > devicetree properties.
> >
> > That's true! One possible solution could be:
> >
> > hwmon_dev {
> > compatible = "hwmon-gpio-simple";
> > name = "gpio-generic-hwmon";
> > update-interval-ms = 100;
> >
> > hwmon-gpio-simple,dev@0 {
> > reg = <0>;
> > gpio = <gpio3 15 GPIO_ACTIVE_LOW>;
> > hwmon-gpio-simple,type = "in";
> > hwmon-gpio-simple,report = "crit_alarm";
> > };
> >
> > hwmon-gpio-simple,dev@1 {
> > reg = <1>;
> > gpio = <gpio3 19 GPIO_ACTIVE_LOW>;
> > hwmon-gpio-simple,type = "temp";
> > hwmon-gpio-simple,report = "alarm";
> > };
> > };
>
> Here's some options:
>
> hwmon_dev {
> /* Orthogonal to existing "gpio-fan" binding. */
> compatible = "gpio-alarm";
> /* Standard DT property for GPIO users is [<name>-]gpios */
> alarm-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>,
> <&gpio3 19 GPIO_ACTIVE_LOW>;
> /* A <prop>-names property is also a DT standard */
> alarm-gpios-names = "in0", "temp0";
temp1, and it would have to specify which alarm, but, yes, that would
be better.
> };
>
> The driver can create hwmon alarm attribute(s) based on the name(s). I
> used "alarm" as it seemed to fit the pattern established by the "fan"
> driver. Both the gpio-fan and gpio-alarm driver use gpios, but I think
> considering them one driver for that reason does not make sense.
>
> The names are very Linuxy, something that is not liked in DT bindings.
> It also doesn't extend well if you need to add more attributes to each
> alarm. Here's something that's more like what I did for the gpio-leds
> binding.
>
> hwmon_dev {
> compatible = "gpio-alarm";
> voltage@0 {
> label = "Battery Voltage Low";
> type = "voltage";
> alarm-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
> };
> cputemp@0 {
> label = "CPU Temperature Critical";
> type = "temperature";
> interrupt-parent = <&gpio3>;
> interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
> };
Even better, though the type of alarm (generic, min, max, lcrit, crit,
cap, emergency, fault) is still needed. That needs to be specified by
some explicit means, not with a label (though having a label is ok).
There could also be more than one alarm per sensor (eg in0_lcrit_alarm,
in0_min_alarm, in0_max_alarm, in0_crit_alarm), all of which would share
a single label. Something like
#define GPIO_ALARM_GENERIC 0
#define GPIO_ALARM_MIN 1
...
voltage@0 {
label = "Battery Voltage";
type = "voltage";
alarm-type = <GPIO_ALARM_LCRIT, GPIO_ALARM_CRIT>;
alarm-gpios = <&gpio3 15 GPIO_ACTIVE_LOW
&gpio3 16 GPIO_ACTIVE_LOW>;
};
with some better (acceptable) values for "alarm-type" and the actual fields.
Guenter
> };
>
> Supporting interrupts instead of just a gpio would allow for edge
> triggering.
>
> I can also see that someone might want to create some kind of time
> based hysteresis for circuits that don't have that. While it would be
> very easy to add a "linux,debounce = <1000>;" property, I imagine that
> would be rejected as configuration in the DT binding.
