Hi, On Wed, Mar 21, 2012 at 08:11:53PM +0100, Karol Lewandowski wrote: > This patch adds support for s3c2440 I2C bus controller dedicated HDMIPHY > device on > Exynos4 platform. Some quirks are introduced due to differences between > HDMIPHY > and other I2C controllers on Exynos4. These differences are: > - no GPIOs, HDMIPHY is inside the SoC and the controller is connected > internally > - due to unknown reason (probably HW bug in HDMIPHY and/or the controller) a > transfer fails to finish. The controller hangs after sending the last byte, > the workaround for this bug is resetting the controller after each transfer > > Signed-off-by: Tomasz Stanislawski <[email protected]> > Signed-off-by: Karol Lewandowski <[email protected]> > Tested-by: Tomasz Stanislawski <[email protected]> > Signed-off-by: Kyungmin Park <[email protected]> > --- > .../devicetree/bindings/i2c/samsung-i2c.txt | 11 +++++- > drivers/i2c/busses/i2c-s3c2410.c | 35 > ++++++++++++++++++++ > 2 files changed, 44 insertions(+), 2 deletions(-) > > diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt > b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt > index 38832c7..c6670f9 100644 > --- a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt > +++ b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt > @@ -10,14 +10,21 @@ Required properties: > region. > - interrupts: interrupt number to the cpu. > - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges. > - - gpios: The order of the gpios should be the following: <SDA, SCL>. > - The gpio specifier depends on the gpio controller. > > Optional properties: > + - gpios: The order of the gpios should be the following: <SDA, SCL>. > + The gpio specifier depends on the gpio controller. Required in all cases > + except when "samsung,i2c-no-gpio" is also specified. > + - samsung,i2c-no-gpio: input/output lines of the controller are > + permanently wired to the respective client, there are no gpio > + lines that need to be configured to enable this controller
Can't we just skip this property...
> - samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
> specified, default value is 0.
> - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
> specified, the default value in Hz is 100000.
> + - samsung,i2c-quirk-hdmiphy: Quirk for HDMI PHY block found on
> + Exynos4 platform - reduce timeout and reset controller after each
> + transfer
... and this one, if we declare a new compatible-entry for exynos4?
>
> Example:
>
> diff --git a/drivers/i2c/busses/i2c-s3c2410.c
> b/drivers/i2c/busses/i2c-s3c2410.c
> index f7b6a14..e50f523 100644
> --- a/drivers/i2c/busses/i2c-s3c2410.c
> +++ b/drivers/i2c/busses/i2c-s3c2410.c
> @@ -50,6 +50,8 @@ static const struct of_device_id s3c24xx_i2c_match[];
>
> /* Treat S3C2410 as baseline hardware, anything else is supported via quirks
> */
> #define QUIRK_S3C2440 (1 << 0)
> +#define QUIRK_HDMIPHY (1 << 1)
> +#define QUIRK_NO_GPIO (1 << 2)
>
> /* i2c controller state */
> enum s3c24xx_i2c_state {
> @@ -469,6 +471,13 @@ static int s3c24xx_i2c_set_master(struct s3c24xx_i2c
> *i2c)
> unsigned long iicstat;
> int timeout = 400;
>
> + /* the timeout for HDMIPHY is reduced to 10 ms because
> + * the hangup is expected to happen, so waiting 400 ms
> + * causes only unnecessary system hangup
> + */
> + if (i2c->quirks & QUIRK_HDMIPHY)
> + timeout = 10;
> +
> while (timeout-- > 0) {
> iicstat = readl(i2c->regs + S3C2410_IICSTAT);
>
> @@ -478,6 +487,15 @@ static int s3c24xx_i2c_set_master(struct s3c24xx_i2c
> *i2c)
> msleep(1);
> }
>
> + /* hang-up of bus dedicated for HDMIPHY occurred, resetting */
> + if (i2c->quirks & QUIRK_HDMIPHY) {
> + writel(0, i2c->regs + S3C2410_IICCON);
> + writel(0, i2c->regs + S3C2410_IICSTAT);
> + writel(0, i2c->regs + S3C2410_IICDS);
> +
> + return 0;
> + }
> +
> return -ETIMEDOUT;
> }
>
> @@ -759,6 +777,9 @@ static int s3c24xx_i2c_parse_dt_gpio(struct s3c24xx_i2c
> *i2c)
> {
> int idx, gpio, ret;
>
> + if (i2c->quirks & QUIRK_NO_GPIO)
> + return 0;
> +
> for (idx = 0; idx < 2; idx++) {
> gpio = of_get_gpio(i2c->dev->of_node, idx);
> if (!gpio_is_valid(gpio)) {
> @@ -783,6 +804,10 @@ free_gpio:
> static void s3c24xx_i2c_dt_gpio_free(struct s3c24xx_i2c *i2c)
> {
> unsigned int idx;
> +
> + if (i2c->quirks & QUIRK_NO_GPIO)
> + return;
> +
> for (idx = 0; idx < 2; idx++)
> gpio_free(i2c->gpios[idx]);
> }
> @@ -859,6 +884,13 @@ s3c24xx_i2c_parse_dt(struct device_node *np, struct
> s3c24xx_i2c *i2c)
> return;
>
> pdata->bus_num = -1; /* i2c bus number is dynamically assigned */
> +
> + if (of_get_property(np, "samsung,i2c-quirk-hdmiphy", NULL))
> + i2c->quirks |= QUIRK_HDMIPHY;
> +
> + if (of_get_property(np, "samsung,i2c-no-gpio", NULL))
> + i2c->quirks |= QUIRK_NO_GPIO;
> +
> of_property_read_u32(np, "samsung,i2c-sda-delay", &pdata->sda_delay);
> of_property_read_u32(np, "samsung,i2c-slave-addr", &pdata->slave_addr);
> of_property_read_u32(np, "samsung,i2c-max-bus-freq",
> @@ -1116,6 +1148,9 @@ static struct platform_device_id s3c24xx_driver_ids[] =
> {
> }, {
> .name = "s3c2440-i2c",
> .driver_data = QUIRK_S3C2440,
> + }, {
> + .name = "s3c2440-hdmiphy-i2c",
> + .driver_data = QUIRK_S3C2440 | QUIRK_HDMIPHY | QUIRK_NO_GPIO,
> }, { },
> };
> MODULE_DEVICE_TABLE(platform, s3c24xx_driver_ids);
> --
> 1.7.9
>
--
Pengutronix e.K. | Wolfram Sang |
Industrial Linux Solutions | http://www.pengutronix.de/ |
signature.asc
Description: Digital signature
