> -----Original Message-----
> From: Mika Westerberg [mailto:mika.westerb...@linux.intel.com]
> Sent: Friday, November 06, 2015 3:46 PM
> To: Yu, Xiangliang
> Cc: andriy.shevche...@linux.intel.com; jarkko.nik...@linux.intel.com;
> w...@the-dreams.de; linux-i2c@vger.kernel.org; linux-
> ker...@vger.kernel.org; Xue, Ken; Wan, Vincent; Huang, Ray; Wang, Annie;
> Li, Tony
> Subject: Re: [PATCH 1/1] I2C: designware: fix IO timeout issue for AMD
> controller
>
> On Fri, Nov 06, 2015 at 04:34:19AM +0000, Yu, Xiangliang wrote:
> > > -----Original Message-----
> > > From: Mika Westerberg [mailto:mika.westerb...@linux.intel.com]
> > > Sent: Thursday, November 05, 2015 9:52 PM
> > > To: Yu, Xiangliang
> > > Cc: andriy.shevche...@linux.intel.com;
> > > jarkko.nik...@linux.intel.com; w...@the-dreams.de;
> > > linux-i2c@vger.kernel.org; linux- ker...@vger.kernel.org; Xue, Ken;
> > > Wan, Vincent; Huang, Ray; Wang, Annie; Li, Tony
> > > Subject: Re: [PATCH 1/1] I2C: designware: fix IO timeout issue for
> > > AMD controller
> > >
> > > On Thu, Nov 05, 2015 at 08:34:44PM +0800, Xiangliang Yu wrote:
> > > > Because of some hardware limitation, AMD I2C controller can't
> > > > trigger next interrupt if interrupt status has been changed after
> > > > clearing interrupt status bits. Then, I2C will lost interrupt and IO
> > > > timeout.
> > > >
> > > > According to hardware design, this patch implements a workaround
> > > > to disable i2c controller interrupt after clearing interrupt bits
> > > > when entering ISR and to enable i2c interrupt before exiting ISR.
> > > >
> > > > To reduce the performance impacts on other vendors, use unlikely
> > > > function to check flag in ISR.
> > > >
> > > > Signed-off-by: Xiangliang Yu <xiangliang...@amd.com>
> > > > ---
> > > > drivers/i2c/busses/i2c-designware-core.c | 6 ++++++
> > > > drivers/i2c/busses/i2c-designware-core.h | 1 +
> > > > drivers/i2c/busses/i2c-designware-platdrv.c | 4 ++++
> > > > 3 files changed, 11 insertions(+)
> > > >
> > > > diff --git a/drivers/i2c/busses/i2c-designware-core.c
> > > > b/drivers/i2c/busses/i2c-designware-core.c
> > > > index 7441cdc..04e7b65 100644
> > > > --- a/drivers/i2c/busses/i2c-designware-core.c
> > > > +++ b/drivers/i2c/busses/i2c-designware-core.c
> > > > @@ -783,6 +783,9 @@ irqreturn_t i2c_dw_isr(int this_irq, void
> > > > *dev_id)
> > > >
> > > > stat = i2c_dw_read_clear_intrbits(dev);
> > >
> > > What if the status changes right here, before you go and mask the
> interrupt?
> > Have no effect, because i2c controller can't trigger next interrupt.
> >
> > >
> > > >
> > > > + if (unlikely(dev->accessor_flags & ACCESS_INTR_MASK))
> > > > + i2c_dw_disable_int(dev);
> > > > +
> > > > if (stat & DW_IC_INTR_TX_ABRT) {
> > > > dev->cmd_err |= DW_IC_ERR_TX_ABRT;
> > > > dev->status = STATUS_IDLE;
> > > > @@ -811,6 +814,9 @@ tx_aborted:
> > > > if ((stat & (DW_IC_INTR_TX_ABRT | DW_IC_INTR_STOP_DET)) ||
> > > dev->msg_err)
> > > > complete(&dev->cmd_complete);
> > > >
> > > > + if (unlikely(dev->accessor_flags & ACCESS_INTR_MASK))
> > > > + dw_writel(dev, DW_IC_INTR_DEFAULT_MASK,
> > > DW_IC_INTR_MASK);
> > >
> > > The driver disables TX interrupt when it is not needed anymore or
> > > when TX gets aborted but the above will re-enable all interrupts
> regardless.
> > > Is that the intention?
> > No, i2c controller can trigger next interrupt only after re-enable all
> > interrupt.
>
> If you get an error the function masks all interrupts and jumps to tx_aborted
> label. With this patch you unmask all interrupts again before exiting the
> function.
>
I see, how about change if statement to else if?
> > >
> > > > +
> > > > return IRQ_HANDLED;
> > > > }
> > > > EXPORT_SYMBOL_GPL(i2c_dw_isr);
> > > > diff --git a/drivers/i2c/busses/i2c-designware-core.h
> > > > b/drivers/i2c/busses/i2c-designware-core.h
> > > > index 9630222..808ef6a 100644
> > > > --- a/drivers/i2c/busses/i2c-designware-core.h
> > > > +++ b/drivers/i2c/busses/i2c-designware-core.h
> > > > @@ -111,6 +111,7 @@ struct dw_i2c_dev {
> > > >
> > > > #define ACCESS_SWAP 0x00000001
> > > > #define ACCESS_16BIT 0x00000002
> > > > +#define ACCESS_INTR_MASK 0x00000004
> > > >
> > > > extern u32 dw_readl(struct dw_i2c_dev *dev, int offset); extern
> > > > void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset); diff
> > > > --git a/drivers/i2c/busses/i2c-designware-platdrv.c
> > > > b/drivers/i2c/busses/i2c-designware-platdrv.c
> > > > index 472b882..0c59357 100644
> > > > --- a/drivers/i2c/busses/i2c-designware-platdrv.c
> > > > +++ b/drivers/i2c/busses/i2c-designware-platdrv.c
> > > > @@ -251,6 +251,10 @@ static int dw_i2c_probe(struct
> > > > platform_device
> > > *pdev)
> > > > dev->rx_fifo_depth = ((param1 >> 8) & 0xff) + 1;
> > > > dev->adapter.nr = pdev->id;
> > > > }
> > > > +
> > > > + if (!strncmp(pdev->name, "AMD0010", 7))
> > > > + dev->accessor_flags |= ACCESS_INTR_MASK;
> > > > +
> > >
> > > Can't you put this to ->driver_data? For example it could refer to a
> > > configuration structure that then contains quirk flags.
> > I think it will need to add a function to support it, but the function
> > Is rarely used. It will easy to add if i2c driver has quirk mechanisms.
> > Added code is very simple and have no influence on others.
>
> What if the next AMD I2C controller needs another quirk, and then another?
>
> I would rather pass flags or similar (reference to config structure including
> flags) with ->driver_data.
>
I don't think there is another quirk.
> >
> > >
> > > > r = i2c_dw_init(dev);
> > > > if (r)
> > > > return r;
> > > > --
> > > > 1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-i2c" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
