Anton Salnikov wrote:
This is Palmchip BK3710 IDE controller support for kernel version 2.6.24-rc8.
The IDE controller logic supports PIO, multiword DMA and ultra-DMA modes.
Supports interface to compact Flash (CF) configured in True-IDE mode.
Signed-off-by: Anton Salnikov <[EMAIL PROTECTED]>
---
Index: 2.6.24-rc8.ide/drivers/ide/arm/palm_bk3710.c
===================================================================
--- /dev/null
+++ 2.6.24-rc8.ide/drivers/ide/arm/palm_bk3710.c
@@ -0,0 +1,428 @@
+static inline u8 hwif_read8(u32 base, u32 reg)
+{
+ return readb(base + reg);
+}
+
+static inline void hwif_write8(u32 base, u8 val, u32 reg)
+{
+ writeb(val, base + reg);
+}
+
+static inline u16 hwif_read16(u32 base, u32 reg)
+{
+ return readw(base + reg);
+}
+
+static inline void hwif_write16(u32 base, u16 val, u32 reg)
+{
+ writew(val, base + reg);
+}
+
+static inline u32 hwif_read32(u32 base, u32 reg)
+{
+ return readl(base + reg);
+}
+
+static inline void hwif_write32(u32 base, u32 val, u32 reg)
+{
+ writel(val, base + reg);
+}
Hm, I don't see why you need those accessors but well...
+static void palm_bk3710_setudmamode(u32 base, unsigned int dev,
+ unsigned int mode)
+{
+ u8 tenv, trp, t0;
+ u32 val32;
+ u16 val16;
+
+ /* DMA Data Setup */
+ t0 = (palm_bk3710_udmatimings[mode].cycletime + ide_palm_clk - 1)
+ / ide_palm_clk - 1;
+ tenv = (20 + ide_palm_clk - 1) / ide_palm_clk - 1;
+ trp = (palm_bk3710_udmatimings[mode].rptime + ide_palm_clk - 1)
+ / ide_palm_clk - 1;
+
+ /* udmatim Register */
+ val16 = hwif_read16(base, BK3710_UDMATIM) & (dev ? 0xFF0F : 0xFFF0);
+ val16 |= (mode << ((!dev) ? 0 : 4));
Why not (dev ? 4 : 0) like the rest?
+ hwif_write16(base, val16, BK3710_UDMATIM);
+
+ /* udmastb Ultra DMA Access Strobe Width */
+ val32 = hwif_read32(base, BK3710_UDMASTB) & (0xFF << (dev ? 0 : 8));
+ val32 |= (t0 << (dev ? 8 : 0));
+ hwif_write32(base, val32, BK3710_UDMASTB);
+
+ /* udmatrp Ultra DMA Ready to Pause Time */
+ val32 = hwif_read32(base, BK3710_UDMATRP) & (0xFF << (dev ? 0 : 8));
+ val32 |= (trp << (dev ? 8 : 0));
+ hwif_write32(base, val32, BK3710_UDMATRP);
+
+ /* udmaenv Ultra DMA envelop Time */
+ val32 = hwif_read32(base, BK3710_UDMAENV) & (0xFF << (dev ? 0 : 8));
+ val32 |= (tenv << (dev ? 8 : 0));
+ hwif_write32(base, val32, BK3710_UDMAENV);
+
+ /* Enable UDMA for Device */
+ val16 = hwif_read16(base, BK3710_UDMACTL) | (1 << dev);
+ hwif_write16(base, val16, BK3710_UDMACTL);
+}
+
+static void palm_bk3710_setdmamode(u32 base, unsigned int dev,
+ unsigned short min_cycle,
+ unsigned int mode)
+{
+ u8 td, tkw, t0;
+ u32 val32;
+ u16 val16;
+
+ unsigned cycletime = max_t(int, ide_timing_find_mode(mode)->cycle,
+ min_cycle);
Hm, why integer comparison and then unsigned maximum?
+
+ /* DMA Data Setup */
+ t0 = (cycletime + ide_palm_clk - 1) / ide_palm_clk;
+ td = (ide_timing_find_mode(mode)->active + ide_palm_clk - 1)
+ / ide_palm_clk;
Couldn't you call ide_timing_find_mode() only once?
[...]
+static int __devinit palm_bk3710_probe(struct platform_device *pdev)
+{
+ hw_regs_t ide_ctlr_info;
+ int index = 0;
+ int pribase;
+ struct clk *clkp;
+ struct resource *mem, *irq;
+ ide_hwif_t *hwif;
+ u32 base;
+ int ret;
+
+ clkp = clk_get(NULL, "IDECLK");
+ if (IS_ERR(clkp))
+ return -ENODEV;
+
+ ideclkp = clkp;
+ clk_enable(ideclkp);
+ ide_palm_clk = clk_get_rate(ideclkp)/100000;
+ ide_palm_clk = (10000/ide_palm_clk) + 1;
+ /* Register the IDE interface with Linux ATA Interface */
+ memset(&ide_ctlr_info, 0, sizeof(ide_ctlr_info));
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (mem == NULL) {
+ printk(KERN_INFO "failed to get memory region resource\n");
This deserves KERN_ERR, not KERN_INFO.
+ return -ENODEV;
+ }
+ irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+ if (irq == NULL) {
+ printk(KERN_INFO "failed to get IRQ resource\n");
This too...
+ return -ENODEV;
+ }
+
+ base = mem->start;
+
+ /* Configure the Palm Chip controller */
+ palm_bk3710_chipinit(base);
+
+ pribase = mem->start + IDE_PALM_ATA_PRI_REG_OFFSET;
+ for (index = 0; index < IDE_NR_PORTS - 2; index++)
+ ide_ctlr_info.io_ports[index] = pribase + index;
+ ide_ctlr_info.io_ports[IDE_CONTROL_OFFSET] = mem->start +
+ IDE_PALM_ATA_PRI_CTL_OFFSET;
+ ide_ctlr_info.irq = irq->start;
+ ide_ctlr_info.chipset = ide_palm3710;
+
+ if (!request_mem_region(mem->start, 8, "palm_bk3710")) {
+ printk(KERN_ERR "Error, memory region in use.\n");
+ return -EBUSY;
+ }
Well, you either have to also register sub-resources for the IDE
command/control register blocks since with hwif->mmiops == 1 the IDE core
won't do this for you, or don't register any sub-resources at all, being
content with what platform_device_add() did for us. BTW, don't forget extend
the platform resource to account for IDE command/control register blocks.
+ if (ide_register_hw(&ide_ctlr_info, NULL, 0, &hwif) < 0) {
+ printk(KERN_WARNING "Palm Chip BK3710 IDE Register Fail\n");
+ return -ENODEV;
+ }
+
+ hwif->set_pio_mode = &palm_bk3710_set_pio_mode;
+ hwif->set_dma_mode = &palm_bk3710_set_dma_mode;
+ hwif->mmio = 1;
Well, dealing with a memory-mapped IDE device, the driver lack
default_hwif_mmiops() call...
MBR, Sergei
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
