Bad news :-(.
Now I am working with my new compiled 2..6.10ac12 kernel.
I can't enable DMA setting.
My system: Slackware 10
# lspci -vv
00:00.0 Host bridge: Toshiba America Info Systems 601 (rev a0)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0, cache line size 08
00:04.0 VGA compatible controller: Chips and Technologies F65555
HiQVPro (rev c6) (prog-if 00 [VGA])
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled] [size=256K]
00:0b.0 USB Controller: NEC Corporation USB (rev 02) (prog-if 10 [OHCI])
Subsystem: Toshiba America Info Systems USB
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 5250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fcfff000 (32-bit, non-prefetchable) [size=4K]
00:11.0 Communication controller: Toshiba America Info Systems FIR Port (rev 21)
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ffe0 [size=32]
# hdparm -i /dev/hda
/dev/hda:
Model=TOSHIBA MK4006MAV, FwRev=F2.03 A, SerialNo=68527172
Config={ Fixed }
RawCHS=7944/16/63, TrkSize=0, SectSize=0, ECCbytes=24
BuffType=unknown, BuffSize=0kB, MaxMultSect=16, MultSect=16
CurCHS=7944/16/63, CurSects=8007552, LBA=yes, LBAsects=8007552
IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 *mdma2
UDMA modes: udma0 udma1 udma2
AdvancedPM=no WriteCache=enabled
* signifies the current active mode
# dmesg
..............
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Probing IDE interface ide0...
hda: TOSHIBA MK4006MAV, ATA DISK drive
Probing IDE interface ide1...
hdc: CD-220EA, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 8007552 sectors (4099 MB), CHS=7944/16/63
hda: cache flushes not supported
hda: hda1 hda2 hda3 hda4
hdc: ATAPI 20X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
................
# hdparm -d1 /dev/hda
/dev/hda:
setting using_dma to 1 (on)
HDIO_SET_DMA failed: Operation not permitted
using_dma = 0 (off)
What can I do?
Marcin Kuk
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
