I get DMA errors after resuming from suspend (S3).
I had switched DMA off before suspending.
Kernel: 2.6.10 (ubuntu, 2.6.10-27), same with 2.6.8.1. Boot Parameters:
ro nobiospnp noapic pci=usepirqmask; same problem without those.
Hardware: Asus K8V SE Deluxe, Via K8T800 Chipset, via82cxxx loaded or
compiled in. No errors with a kernel without that module.
This is the last dmesg:
hda: DMA disabled
hdb: DMA disabled
hdc: DMA disabled
hdd: DMA disabled
Stopping tasks: ==============================================|
Back to C!
powernow-k8: ph2 null fid transition 0xc
ACPI: PCI interrupt 0000:00:07.0[A] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI interrupt 0000:00:0a.0[A] -> GSI 10 (level, low) -> IRQ 10
eth1: link down
ACPI: PCI interrupt 0000:00:0f.0[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:0f.1[A] -> GSI 11 (level, low) -> IRQ 11
Restarting tasks... done
usb 5-4: USB disconnect, address 3
VFS: busy inodes on changed media.
input: AT Translated Set 2 keyboard on isa0060/serio0
usb 5-4: new high speed USB device using ehci_hcd and address 4
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
Vendor: HL-DT-ST Model: DVDRAM GSA-4163B Rev: A101
Type: CD-ROM ANSI SCSI revision: 00
sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr0 at scsi3, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi3, channel 0, id 0, lun 0, type 5
usb-storage: device scan complete
hda: dma_timer_expiry: dma status == 0x61
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete
DataRequest }
ide: failed opcode was: unknown
hda: status timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hdb: DMA disabled
hda: drive not ready for command
ide0: reset: success
hda: dma_timer_expiry: dma status == 0x21
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete
DataRequest }
ide: failed opcode was: unknown
hda: status timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hda: drive not ready for command
ide0: reset: success
hda: dma_timer_expiry: dma status == 0x21
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete
DataRequest }
ide: failed opcode was: unknown
hda: status timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hda: drive not ready for command
ide0: reset: success
hda: dma_timer_expiry: dma status == 0x21
hda: DMA timeout error
hda: dma timeout error: status=0x58 { DriveReady SeekComplete
DataRequest }
ide: failed opcode was: unknown
hda: status timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hda: drive not ready for command
ide0: reset: success
Thanks
David
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
