Hi Jeff,

Desc:
   pdc2027x: fix the PLL input clock detection problem:
Sometimes the pdc2027x driver reads incorrect value from the counter and 
initialize the hardware with incorrect clock rate.

Root Cause:

- The PLL input clock counter on the pdc2027x is a 30-bit deceasing counter.
  The driver reads the decreasing counter byte by byte and assemsble back the
  whole 30-bit counter when detecting the PLL input clock rate on the fly.

- The driver reads the counter from LSB then MSB, byte by byte.
  For example, for 7D030093, the driver read  93, 00, 03 and 7D,
  piece by piece. (This is pdc2027x hardware limitation.)

- The counter is running when the driver reads it.
  Ex. When 7D030093 decreasing to 7D027FFF, sometimes the driver will read 
7D020093.
  That is, when the driver read LSB, LSB 0093 is quite close to zero. Later 
when the
  driver read MSB, MSB is already changed from 7D03 to 7D02. => The driver
  assembles the wrong bytes and gets 7D020093.

Changes:
- Verify whether the driver is reading while the MSB bits of the counter is 
changing.
  If yes, reread the counter. (Incorrect LSB bits only affect the result by 
less than 5% under 100ms
  delay time and can be ignored.)

- Change the delay time from 1ms to 100ms. This can make the detected clock 
rate more accurate.
The extra time spent on rereading the counter is less than 1% compared to 100ms.

Attached please find the patch 4/4 against the libata-dev-2.6 tree for your 
review. Thanks.

Albert

Signed-off-by: Albert Lee <[EMAIL PROTECTED]>
--- libata-dev-2.6-reorg/drivers/scsi/pata_pdc2027x.c   2005-04-11 
15:05:28.000000000 +0800
+++ libata-dev-2.6-pll-fix/drivers/scsi/pata_pdc2027x.c 2005-04-11 
15:05:42.000000000 +0800
@@ -29,7 +29,7 @@
 #include <asm/io.h>
 
 #define DRV_NAME       "pata_pdc2027x"
-#define DRV_VERSION    "0.59"
+#define DRV_VERSION    "0.60"
 #undef PDC_DEBUG
 
 #ifdef PDC_DEBUG
@@ -463,7 +463,10 @@
 {
        u8 ctr0, ctr1, ctr2, ctr3;
        unsigned long counter;
+       u8 ctr0v, ctr1v, ctr2v, ctr3v;
+       int retry = 1;
 
+retry:
        outb(0x20, probe_ent->port[0].bmdma_addr + 0x01);
        ctr0 = inb(probe_ent->port[0].bmdma_addr + 0x03);
        outb(0x21, probe_ent->port[0].bmdma_addr + 0x01);
@@ -473,10 +476,32 @@
        outb(0x21, probe_ent->port[1].bmdma_addr + 0x01);
        ctr3 = inb(probe_ent->port[1].bmdma_addr + 0x03);
 
+       /* Read the counter values again for verification */
+       outb(0x20,  probe_ent->port[0].bmdma_addr + 0x01);
+       ctr0v = inb(probe_ent->port[0].bmdma_addr + 0x03);
+       outb(0x21,  probe_ent->port[0].bmdma_addr + 0x01);
+       ctr1v = inb(probe_ent->port[0].bmdma_addr + 0x03);
+       outb(0x20,  probe_ent->port[1].bmdma_addr + 0x01);
+       ctr2v = inb(probe_ent->port[1].bmdma_addr + 0x03);
+       outb(0x21,  probe_ent->port[1].bmdma_addr + 0x01);
+       ctr3v = inb(probe_ent->port[1].bmdma_addr + 0x03);
+
        counter = (ctr3 << 23) | (ctr2 << 15) | (ctr1 << 8) | ctr0;
 
        PDPRINTK("ctr0[%X] ctr1[%X] ctr2[%X] ctr3[%X]\n", 
                 ctr0, ctr1, ctr2, ctr3);
+       PDPRINTK("ctr0[%X] ctr1[%X] ctr2[%X] ctr3[%X]\n", 
+                ctr0v, ctr1v, ctr2v, ctr3v);
+
+       /*
+        * The 30-bit decreasing counter are read by 4 pieces.
+        * Incorrect value may be read when ctr2 and ctr3 are changing.
+        */
+       if (retry && !(ctr3 == ctr3v && ctr2 == ctr2v && ctr1 >= ctr1v)) {
+               retry--;
+               PDPRINTK("rereading counter\n");
+               goto retry;
+       }
 
        return counter;
 }
@@ -599,8 +624,8 @@
        PDPRINTK("scr1[%X]\n", scr1);
        outb(scr1 | 0x40, probe_ent->port[0].bmdma_addr + 0x03);
 
-       /* Let the counter run for 1000 us. */
-       udelay(1000);
+       /* Let the counter run for 100 ms. */
+       mdelay(100);
 
        /* Read the counter values again */
        end_count = pdc_read_counter(probe_ent);
@@ -612,7 +637,7 @@
        outb(scr1 & 0xBF, probe_ent->port[0].bmdma_addr + 0x03);
 
        /* calculate the input clock in Hz */
-       pll_clock = (long) ((start_count - end_count) * 1000);
+       pll_clock = (long) ((start_count - end_count) * 10);
 
        PDPRINTK("start[%lu] end[%lu] \n", start_count, end_count);
        PDPRINTK("PLL input clock[%ld]Hz\n", pll_clock);

Reply via email to