Yes its no longer 3x2n but 3xxn, I can rename it if you want Jeff
- Don't reset both ports each time (Sergei)
- If we can't get a DPLL then abort entirely
- Use ioport access for clock (from drivers/ide)
- Add HPT371N support (from drivers/ide)
Signed-off-by: Alan Cox <[EMAIL PROTECTED]>
diff -u --new-file --recursive --exclude-from /usr/src/exclude
linux.vanilla-2.6.21-rc4-mm1/drivers/ata/pata_hpt3x2n.c
linux-2.6.21-rc4-mm1/drivers/ata/pata_hpt3x2n.c
--- linux.vanilla-2.6.21-rc4-mm1/drivers/ata/pata_hpt3x2n.c 2007-03-23
11:49:49.000000000 +0000
+++ linux-2.6.21-rc4-mm1/drivers/ata/pata_hpt3x2n.c 2007-03-23
13:33:34.000000000 +0000
@@ -8,10 +8,10 @@
* Copyright (C) 1999-2003 Andre Hedrick <[EMAIL PROTECTED]>
* Portions Copyright (C) 2001 Sun Microsystems, Inc.
* Portions Copyright (C) 2003 Red Hat Inc
+ * Portions Copyright (C) 2005-2006 MontaVista Software, Inc.
*
*
* TODO
- * 371N
* Work out best PLL policy
*/
@@ -142,6 +142,7 @@
/**
* hpt3x2n_pre_reset - reset the hpt3x2n bus
* @ap: ATA port to reset
+ * @deadline: deadline jiffies for the operation
*
* Perform the initial reset handling for the 3x2n series controllers.
* Reset the hardware and state machine,
@@ -151,8 +152,7 @@
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
/* Reset the state machine */
- pci_write_config_byte(pdev, 0x50, 0x37);
- pci_write_config_byte(pdev, 0x54, 0x37);
+ pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37);
udelay(100);
return ata_std_prereset(ap, deadline);
@@ -434,8 +434,9 @@
{
unsigned long freq;
u32 fcnt;
+ unsigned long iobase = pci_resource_start(pdev, 4);
- pci_read_config_dword(pdev, 0x70/*CHECKME*/, &fcnt);
+ fcnt = inl(iobase + 0x90); /* Not PCI readable for some chips */
if ((fcnt >> 12) != 0xABCDE) {
printk(KERN_WARNING "hpt3xn: BIOS clock data not set.\n");
return 33; /* Not BIOS set */
@@ -504,6 +505,7 @@
unsigned int pci_mhz;
unsigned int f_low, f_high;
int adjust;
+ unsigned long iobase = pci_resource_start(dev, 4);
pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
class_rev &= 0xFF;
@@ -513,6 +515,11 @@
if (class_rev < 6)
return -ENODEV;
break;
+ case PCI_DEVICE_ID_TTI_HPT371:
+ if (class_rev < 2)
+ return -ENODEV;
+ /* 371N if rev > 1 */
+ break;
case PCI_DEVICE_ID_TTI_HPT372:
/* 372N if rev >= 1*/
if (class_rev == 0)
@@ -539,6 +546,19 @@
pci_read_config_byte(dev, 0x5A, &irqmask);
irqmask &= ~0x10;
pci_write_config_byte(dev, 0x5a, irqmask);
+
+ /*
+ * HPT371 chips physically have only one channel, the secondary one,
+ * but the primary channel registers do exist! Go figure...
+ * So, we manually disable the non-existing channel here
+ * (if the BIOS hasn't done this already).
+ */
+ if (dev->device == PCI_DEVICE_ID_TTI_HPT371) {
+ u8 mcr1;
+ pci_read_config_byte(dev, 0x50, &mcr1);
+ mcr1 &= ~0x04;
+ pci_write_config_byte(dev, 0x50, mcr1);
+ }
/* Tune the PLL. HPT recommend using 75 for SATA, 66 for UDMA133 or
50 for UDMA100. Right now we always use 66 */
@@ -558,14 +578,24 @@
break;
pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
}
- if (adjust == 8)
- printk(KERN_WARNING "hpt3xn: DPLL did not stabilize.\n");
+ if (adjust == 8) {
+ printk(KERN_WARNING "hpt3x2n: DPLL did not stabilize.\n");
+ return -ENODEV;
+ }
/* Set our private data up. We only need a few flags so we use
it directly */
port->private_data = NULL;
- if (pci_mhz > 60)
+ if (pci_mhz > 60) {
port->private_data = (void *)PCI66;
+ /*
+ * On HPT371N, if ATA clock is 66 MHz we must set bit 2 in
+ * the MISC. register to stretch the UltraDMA Tss timing.
+ * NOTE: This register is only writeable via I/O space.
+ */
+ if (dev->device == PCI_DEVICE_ID_TTI_HPT371)
+ outb(inb(iobase + 0x9c) | 0x04, iobase + 0x9c);
+ }
/* Now kick off ATA set up */
port_info[0] = port_info[1] = port;
@@ -574,6 +604,7 @@
static const struct pci_device_id hpt3x2n[] = {
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
+ { PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT371), },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372), },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT302), },
{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT372N), },
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
