From: Borislav Petkov <[EMAIL PROTECTED]>
Those are already in mtio.h.
Signed-off-by: Borislav Petkov <[EMAIL PROTECTED]>
---
drivers/ide/ide-tape.c | 96 +++++++----------------------------------------
1 files changed, 15 insertions(+), 81 deletions(-)
diff --git a/drivers/ide/ide-tape.c b/drivers/ide/ide-tape.c
index d4c4255..cfb26d9 100644
--- a/drivers/ide/ide-tape.c
+++ b/drivers/ide/ide-tape.c
@@ -3028,69 +3028,20 @@ static int idetape_write_filemark (ide_drive_t *drive)
}
/*
- * idetape_mtioctop is called from idetape_chrdev_ioctl when
- * the general mtio MTIOCTOP ioctl is requested.
+ * Called from idetape_chrdev_ioctl when the general mtio MTIOCTOP ioctl is
+ * requested.
*
- * We currently support the following mtio.h operations:
+ * Note: MTBSF and MTBSFM are not supported when the tape doesn't support
+ * spacing over filemarks in the reverse direction. In this case, MTFSFM is
also
+ * usually not supported (it is supported in the rare case in which we crossed
+ * the filemark during our read-ahead pipelined operation mode).
*
- * MTFSF - Space over mt_count filemarks in the positive direction.
- * The tape is positioned after the last spaced filemark.
+ * The following commands are currently not supported:
*
- * MTFSFM - Same as MTFSF, but the tape is positioned before the
- * last filemark.
- *
- * MTBSF - Steps background over mt_count filemarks, tape is
- * positioned before the last filemark.
- *
- * MTBSFM - Like MTBSF, only tape is positioned after the last
filemark.
- *
- * Note:
- *
- * MTBSF and MTBSFM are not supported when the tape doesn't
- * support spacing over filemarks in the reverse direction.
- * In this case, MTFSFM is also usually not supported (it is
- * supported in the rare case in which we crossed the filemark
- * during our read-ahead pipelined operation mode).
- *
- * MTWEOF - Writes mt_count filemarks. Tape is positioned after
- * the last written filemark.
- *
- * MTREW - Rewinds tape.
- *
- * MTLOAD - Loads the tape.
- *
- * MTOFFL - Puts the tape drive "Offline": Rewinds the tape and
- * MTUNLOAD prevents further access until the media is replaced.
- *
- * MTNOP - Flushes tape buffers.
- *
- * MTRETEN - Retension media. This typically consists of one end
- * to end pass on the media.
- *
- * MTEOM - Moves to the end of recorded data.
- *
- * MTERASE - Erases tape.
- *
- * MTSETBLK - Sets the user block size to mt_count bytes. If
- * mt_count is 0, we will attempt to autodetect
- * the block size.
- *
- * MTSEEK - Positions the tape in a specific block number, where
- * each block is assumed to contain which user_block_size
- * bytes.
- *
- * MTSETPART - Switches to another tape partition.
- *
- * MTLOCK - Locks the tape door.
- *
- * MTUNLOCK - Unlocks the tape door.
- *
- * The following commands are currently not supported:
- *
- * MTFSS, MTBSS, MTWSM, MTSETDENSITY,
- * MTSETDRVBUFFER, MT_ST_BOOLEANS, MT_ST_WRITE_THRESHOLD.
+ * MTFSS, MTBSS, MTWSM, MTSETDENSITY, MTSETDRVBUFFER, MT_ST_BOOLEANS,
+ * MT_ST_WRITE_THRESHOLD.
*/
-static int idetape_mtioctop (ide_drive_t *drive,short mt_op,int mt_count)
+static int idetape_mtioctop(ide_drive_t *drive, short mt_op, int mt_count)
{
idetape_tape_t *tape = drive->driver_data;
idetape_pc_t pc;
@@ -3203,29 +3154,12 @@ static int idetape_mtioctop (ide_drive_t *drive,short
mt_op,int mt_count)
}
/*
- * Our character device ioctls.
- *
- * General mtio.h magnetic io commands are supported here, and not in
- * the corresponding block interface.
- *
- * The following ioctls are supported:
- *
- * MTIOCTOP - Refer to idetape_mtioctop for detailed description.
- *
- * MTIOCGET - The mt_dsreg field in the returned mtget structure
- * will be set to (user block size in bytes <<
- * MT_ST_BLKSIZE_SHIFT) & MT_ST_BLKSIZE_MASK.
- *
- * The mt_blkno is set to the current user block number.
- * The other mtget fields are not supported.
- *
- * MTIOCPOS - The current tape "block position" is returned. We
- * assume that each block contains user_block_size
- * bytes.
- *
- * Our own ide-tape ioctls are supported on both interfaces.
+ * Our character device ioctls. General mtio.h magnetic io commands are
+ * supported here, and not in the corresponding block interface. Our own
+ * ide-tape ioctls are supported on both interfaces.
*/
-static int idetape_chrdev_ioctl (struct inode *inode, struct file *file,
unsigned int cmd, unsigned long arg)
+static int idetape_chrdev_ioctl(struct inode *inode, struct file *file,
+ uint cmd, ulong arg)
{
struct ide_tape_obj *tape = ide_tape_f(file);
ide_drive_t *drive = tape->drive;
--
1.5.3.7
-
To unsubscribe from this list: send the line "unsubscribe linux-ide" in
the body of a message to [EMAIL PROTECTED]
More majordomo info at http://vger.kernel.org/majordomo-info.html
