Oleg Goldshmidt wrote:
Of course. So does the IBM boot CD (which is a Linux live CD, btw. I'll disassemble it if things continue to fail), and the BIOS supplied setup program (which is how I set up a Raid in the first place).Shachar Shemesh <[EMAIL PROTECTED]> writes:
It may be something quite stupid. Maybe just the PCI ID changing. Then
again, it may be something more serious.
Does the BIOS recognize the device?
What about lspci -vv?
attached
I will, though it seems that it's only defined in the device list there, not in any device module. I'm not sure I understand the kernel structure enough to know for sure, however.Grepping 2.6.10:
/drivers/pci/devlist.h:9040: DEVICE(9005,809d,"AIC-7902(B) U320 w/HostRAID")
Try 2.6.10. Maybe it's easier than anything else...
If that does not work, try a RH kernel? At least see if there areaic79xx is the SCSI controller. Once a raid is defined, the disks that participate in the RAID are removed from the SCSI enumeration. It is therefor not the right driver for the job. As I wrote Ira before, if no hardware RAID is defined, I can install Debian Sarge amd64 on the machine using the AIC79xx (though, for some reason, not Debian Sarge IA32).
differences in ips and the aic-whatever?
As for the RH kernels - RHAS3 by default does not find any drives either. I'm going to check the IBM site if they have any special drivers. If they don't, I'm going to call IBM's support. RHAS3 is a supported platform for this machine.
Shachar
-- Shachar Shemesh Lingnu Open Source Consulting ltd. http://www.lingnu.com/
00:00.0 Host bridge: Intel Corp. E7520 Memory Controller Hub (rev 0c)
Subsystem: IBM: Unknown device 02dd
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Region 1: Memory at <ignored> (32-bit, non-prefetchable)
Capabilities: [40] Vendor Specific Information
00:00.1 Class ff00: Intel Corp. E7525/E7520 Error Reporting Registers (rev 0c)
Subsystem: IBM: Unknown device 02dd
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:02.0 PCI bridge: Intel Corp. E7525/E7520/E7320 PCI Express Port A (rev 0c)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=02, subordinate=04, sec-latency=0
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1
Enable-
Address: fee00000 Data: 0000
Capabilities: [64] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 2
Link: Latency L0s <4us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Root: Correctable+ Non-Fatal+ Fatal+ PME+
Capabilities: [100] Advanced Error Reporting
00:04.0 PCI bridge: Intel Corp. E7525/E7520 PCI Express Port B (rev 0c)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Memory behind bridge: ce000000-cfffffff
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1
Enable-
Address: fee00000 Data: 0000
Capabilities: [64] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 4
Link: Latency L0s <4us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Advanced Error Reporting
00:05.0 PCI bridge: Intel Corp. E7520 PCI Express Port B1 (rev 0c) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Memory behind bridge: cc000000-cdffffff
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1
Enable-
Address: fee00000 Data: 0000
Capabilities: [64] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 5
Link: Latency L0s <4us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Root: Correctable- Non-Fatal- Fatal- PME-
Capabilities: [100] Advanced Error Reporting
00:06.0 PCI bridge: Intel Corp. E7520 PCI Express Port C (rev 0c) (prog-if 00
[Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=00, secondary=07, subordinate=09, sec-latency=0
I/O behind bridge: 00004000-0000ffff
Memory behind bridge: ca000000-cbffffff
Prefetchable memory behind bridge: 00000000c9000000-00000000c9f00000
Secondary status: 66Mhz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1
Enable-
Address: fee00000 Data: 0000
Capabilities: [64] Express Root Port (Slot-) IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 6
Link: Latency L0s <4us, L1 unlimited
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Root: Correctable+ Non-Fatal+ Fatal+ PME+
Capabilities: [100] Advanced Error Reporting
00:08.0 System peripheral: Intel Corp. E7525/E7520/E7320 Extended Configuration
Registers (rev 0c)
Subsystem: IBM: Unknown device 02dd
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
00:1d.0 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI Controller
#1 (rev 02) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 02dd
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 169
Region 4: I/O ports at 2200 [size=32]
00:1d.1 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB UHCI Controller
#2 (rev 02) (prog-if 00 [UHCI])
Subsystem: IBM: Unknown device 02dd
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 177
Region 4: I/O ports at 2600 [size=32]
00:1d.7 USB Controller: Intel Corp. 82801EB/ER (ICH5/ICH5R) USB2 EHCI
Controller (rev 02) (prog-if 20 [EHCI])
Subsystem: IBM: Unknown device 02dd
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 185
Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] Debug port
00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev c2) (prog-if 00 [Normal
decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00003000-00003fff
Memory behind bridge: de000000-dfffffff
Prefetchable memory behind bridge: d0000000-ddffffff
Secondary status: 66Mhz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge
(rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801EB/ER (ICH5/ICH5R) IDE Controller (rev
02) (prog-if 8a [Master SecP PriP])
Subsystem: IBM: Unknown device 02dd
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at <ignored>
Region 1: I/O ports at <ignored>
Region 2: I/O ports at <ignored>
Region 3: I/O ports at <ignored>
Region 4: I/O ports at 0480 [size=16]
Region 5: Memory at 40000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corp. 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
Subsystem: IBM: Unknown device 02dd
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 193
Region 4: I/O ports at 0440 [size=32]
01:06.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon
7000/VE] (prog-if 00 [VGA])
Subsystem: IBM: Unknown device 02c8
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2000ns min), Cache Line Size 10
Interrupt: pin A routed to IRQ 217
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at dfff0000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:00.0 PCI bridge: Intel Corp. 6700PXH PCI Express-to-PCI Bridge A (rev 09)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=3
Status: Bus=2 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] Power Budgeting
02:00.2 PCI bridge: Intel Corp. 6700PXH PCI Express-to-PCI Bridge B (rev 09)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=02, secondary=04, subordinate=04, sec-latency=64
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=3
Status: Bus=2 Dev=0 Func=2 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] Power Budgeting
05:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit
Ethernet PCI Express (rev 11)
Subsystem: IBM: Unknown device 02c6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Interrupt: pin A routed to IRQ 169
Region 0: Memory at cfff0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
Address: 68df7be202fddcec Data: bb7f
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <2us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
06:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5721 Gigabit
Ethernet PCI Express (rev 11)
Subsystem: IBM: Unknown device 02c6
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Interrupt: pin A routed to IRQ 169
Region 0: Memory at cdff0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
Address: a04bdf671fbc3ec4 Data: 73e9
Capabilities: [d0] Express Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <2us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
07:00.0 PCI bridge: Intel Corp. 80332 [Dobson] I/O processor (rev 07) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=07, secondary=08, subordinate=08, sec-latency=64
I/O behind bridge: 00004000-00004fff
Memory behind bridge: ca000000-cbffffff
Prefetchable memory behind bridge: 00000000c9000000-00000000c9f00000
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=3
Status: Bus=7 Dev=0 Func=0 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] Power Budgeting
07:00.2 PCI bridge: Intel Corp. 80332 [Dobson] I/O processor (rev 07) (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size 10
Bus: primary=07, secondary=09, subordinate=09, sec-latency=64
I/O behind bridge: 00005000-0000ffff
Secondary status: 66Mhz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <64ns, L1 <1us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
Link: Latency L0s unlimited, L1 unlimited
Link: ASPM Disabled CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x8
Capabilities: [5c] Message Signalled Interrupts: 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [6c] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [d8] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-, SRD- Freq=2
Status: Bus=7 Dev=0 Func=2 64bit- 133MHz- SCD- USC-, SCO-, SRD-
: Upstream: Capacity=65535, Commitment Limit=65535
: Downstream: Capacity=65535, Commitment Limit=65535
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] Power Budgeting
08:07.0 SCSI storage controller: Adaptec AIC-7902B U320 (rev 10)
Subsystem: IBM: Unknown device 02cc
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), Cache Line Size 10
Interrupt: pin A routed to IRQ 201
Region 0: I/O ports at 4000 [disabled] [size=256]
Region 1: Memory at cbffe000 (64-bit, non-prefetchable) [size=8K]
Region 3: I/O ports at 4100 [disabled] [size=256]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [94] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=3
Status: Bus=8 Dev=7 Func=0 64bit+ 133MHz+ SCD- USC-, DC=simple,
DMMRBC=0, DMOST=4, DMCRS=1, RSCEM-
08:07.1 RAID bus controller: Adaptec AIC-7902(B) U320 w/HostRAID (rev 10)
Subsystem: IBM: Unknown device 02cc
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64 (10000ns min, 6250ns max), Cache Line Size 10
Interrupt: pin B routed to IRQ 209
Region 0: I/O ports at 4200 [size=256]
Region 1: Memory at cbffc000 (64-bit, non-prefetchable) [size=8K]
Region 3: I/O ports at 4300 [size=256]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] Message Signalled Interrupts: 64bit+ Queue=0/1
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [94] PCI-X non-bridge device.
Command: DPERE- ERO+ RBC=0 OST=3
Status: Bus=8 Dev=7 Func=1 64bit+ 133MHz+ SCD- USC-, DC=simple,
DMMRBC=0, DMOST=4, DMCRS=1, RSCEM-
