Stupid of me not to have looked at dmesg before writing. It turned out to be a bad USB cable - so I wasn't connecting :-(
Thanks for pointing me in the write direction On Tue, 20 Jun 2017 15:04:57 +0300 Rabin Yasharzadehe <[email protected]> wrote: > what is the output of `dmesg` when you connect the device to the > machine ? > > e.g, should be something like this, > > [393503.604738] usb 1-4.2: new full-speed USB device number 71 using > xhci_hcd > [393503.698674] usb 1-4.2: New USB device found, idVendor=1a86, > idProduct=7523 > [393503.698678] usb 1-4.2: New USB device strings: Mfr=0, Product=2, > SerialNumber=0 > [393503.698681] usb 1-4.2: Product: USB2.0-Serial > [393503.757764] usbcore: registered new interface driver ch341 > [393503.757789] usbserial: USB Serial support registered for > ch341-uart [393503.757808] ch341 1-4.2:1.0: ch341-uart converter > detected [393503.758600] usb 1-4.2: ch341-uart converter now attached > to ttyUSB0 > > > -- > Rabin > > On 20 June 2017 at 14:20, Shlomo Solomon <[email protected]> > wrote: > > > Sorry - just noticed I cut off part of the error message, so here > > it is again: > > > > WARNING: RXTX Version mismatch > > Jar version = RXTX-2.2 > > native lib Version = RXTX-2.2pre2 > > Binary sketch size: 1,056 bytes (of a 32,256 byte maximum) > > avrdude: stk500_recv(): programmer is not responding > > avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00 > > avrdude: stk500_recv(): programmer is not responding > > avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00 > > > > > > > > > > > > On Tue, 20 Jun 2017 13:32:28 +0300 > > Shlomo Solomon <[email protected]> wrote: > > > > > I installed the Arduino IDE from Mageia RPMs and added my user to > > > the lock group as instructed. > > > > > > In the tools >> serial port menu, there is no /dev/ttyUSB0 - > > > only /dev/ttyS0 and /dev/ttyS1. I tried both of them but could > > > not upload a program. I read that sometimes Arduino needs to be > > > run as root, so I tried that too with no success. Here's what I > > > get when I try to upload: > > > > > > Binary sketch size: 1,056 bytes (of a 32,256 byte maximum) > > > Binary sketch size: 1,056 bytes (of a 32,256 byte maximum) > > > avrdude: stk500_recv(): programmer is not responding > > > avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x00 > > > avrdude: stk500_recv(): programmer is not responding > > > avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00 > > > avrdude: stk500_recv(): programmer is not responding > > > > > > > > > > > > > > > > > -- > > Shlomo Solomon > > http://the-solomons.net > > Sent by Claws Mail 3.11.1 - KDE 4.14.5 - LINUX Mageia 5 > > > > > > _______________________________________________ > > Linux-il mailing list > > [email protected] > > http://mailman.cs.huji.ac.il/mailman/listinfo/linux-il > > -- Shlomo Solomon http://the-solomons.net Sent by Claws Mail 3.11.1 - KDE 4.14.5 - LINUX Mageia 5 _______________________________________________ Linux-il mailing list [email protected] http://mailman.cs.huji.ac.il/mailman/listinfo/linux-il
