Hi Dmitry,
On 8/22/2012 13:55, Dmitry Torokhov wrote:
Hi Bo,
On Mon, Aug 20, 2012 at 11:41:10AM +0800, Bo Shen wrote:
This patch enable the qt1070 device tree support
If using device tree, the node of qt1070 looks like
i2c@0 { // this is an example
status = "okay"; // Enable i2c master
qt1070@1b {
compatible = "atmel,qt1070"; // FDT device id
reg = <0x1b>; // qt1070 i2c address
change-gpio = <&pioA 7 1>; // gpio used as interrupt
};
};
Signed-off-by: Bo Shen <[email protected]>
---
change since v1
Add gpio relative stuff, gpio_is_valid, gpio_request
---
drivers/input/keyboard/qt1070.c | 31 +++++++++++++++++++++++++++----
1 file changed, 27 insertions(+), 4 deletions(-)
diff --git a/drivers/input/keyboard/qt1070.c b/drivers/input/keyboard/qt1070.c
index ca68f29..2717bb4 100644
--- a/drivers/input/keyboard/qt1070.c
+++ b/drivers/input/keyboard/qt1070.c
@@ -33,6 +33,8 @@
#include <linux/interrupt.h>
#include <linux/jiffies.h>
#include <linux/delay.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
/* Address for each register */
#define CHIP_ID 0x00
@@ -155,11 +157,25 @@ static int __devinit qt1070_probe(struct i2c_client
*client,
return -ENODEV;
}
- if (!client->irq) {
+ if (client->dev.of_node)
+ client->irq = of_get_named_gpio(client->dev.of_node,
+ "change-gpio", 0);
I'd say this gpio to irq DT mapping should be done by the same code that
parses I2C address and creates client structure.
After digging it, I think this need some other parts support. Maybe gpio
pinctrl or something else, I am not sure.
I try add two line as following in dts node. But can not get irq when
test it on my DT supported platform.
----------cut here---------
+ qt1070@1b {
+ compatible = "atmel,qt1070";
+ reg = <0x1b>;
+ interrupt-parent = <&pioA>;
+ interrupts = <7 2>;
---------------------------
So, please give me some advice for this.
Thanks.
+
+ if (!client->irq || client->irq < 0) {
dev_err(&client->dev, "please assign the irq to this device\n");
return -EINVAL;
}
+ if (gpio_is_valid(client->irq)) {
+ if (gpio_request(client->irq, "qt1070-change")) {
+ dev_err(&client->dev, "request gpio failed\n");
+ return -EINVAL;
+ }
+ } else {
+ dev_err(&client->dev, "gpio is not valid\n");
+ return -EINVAL;
+ }
+
/* Identify the qt1070 chip */
if (!qt1070_identify(client))
return -ENODEV;
@@ -200,9 +216,9 @@ static int __devinit qt1070_probe(struct i2c_client *client,
qt1070_write(client, RESET, 1);
msleep(QT1070_RESET_TIME);
- err = request_threaded_irq(client->irq, NULL, qt1070_interrupt,
- IRQF_TRIGGER_NONE | IRQF_ONESHOT,
- client->dev.driver->name, data);
+ err = request_threaded_irq(gpio_to_irq(client->irq), NULL,
This will surely break non-DT case.
Thanks, I will fix it in next version.
+ qt1070_interrupt, IRQF_TRIGGER_NONE | IRQF_ONESHOT,
+ "qt1070-change", data);
if (err) {
dev_err(&client->dev, "fail to request irq\n");
goto err_free_mem;
@@ -243,6 +259,12 @@ static int __devexit qt1070_remove(struct i2c_client
*client)
return 0;
}
+static const struct of_device_id atmel_qt1070_of_match[] = {
+ { .compatible = "atmel,qt1070", },
+ { },
+};
+MODULE_DEVICE_TABLE(of, atmel_qt1070_of_match);
+
static const struct i2c_device_id qt1070_id[] = {
{ "qt1070", 0 },
{ },
@@ -253,6 +275,7 @@ static struct i2c_driver qt1070_driver = {
.driver = {
.name = "qt1070",
.owner = THIS_MODULE,
+ .of_match_table = atmel_qt1070_of_match,
},
.id_table = qt1070_id,
.probe = qt1070_probe,
--
1.7.10
Thanks.
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
