On Tue, Jul 28, 2015 at 10:26:48AM +0200, Dirk Behme wrote:
> Add support for hardware which uses an I2C Serializer / Deserializer
> (SerDes) to communicate with the zFroce touch driver. In this case the
> SerDes will be configured as an interrupt controller and the zForce driver
> will have no access to poll the GPIO line.
>
> To support this, we add two dedicated new GPIOs in the device tree:
> rst-gpio and int-gpio. With the int-gpio being optional, then.
>
> To not break the existing device trees, the index based 'gpios' entries
> are still supported, but marked as depreciated.
>
> With this, if the interrupt GPIO is available, either via the old or new
> device tree style, the while loop will read and handle the packets as long
> as the GPIO indicates that the interrupt is asserted (existing, unchanged
> driver behavior).
>
> If the interrupt GPIO isn't available, i.e. not configured via the new
> device tree style, we are falling back to one read per ISR invocation
> (new behavior to support the SerDes).
>
> Note that the gpiod functions help to handle the optional GPIO:
> devm_gpiod_get_index_optional() will return NULL in case the interrupt
> GPIO isn't available. And gpiod_get_value_cansleep() does cover this, too,
> by returning 0 in this case.
Let's let Heiko take a look as well.
>
> Signed-off-by: Dirk Behme <dirk.be...@de.bosch.com>
> ---
> .../bindings/input/touchscreen/zforce_ts.txt | 8 ++--
> drivers/input/touchscreen/zforce_ts.c | 49
> +++++++++++++++++++++-
> 2 files changed, 52 insertions(+), 5 deletions(-)
>
> diff --git
> a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt
> b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt
> index 80c37df..c6be925 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt
> @@ -4,12 +4,12 @@ Required properties:
> - compatible: must be "neonode,zforce"
> - reg: I2C address of the chip
> - interrupts: interrupt to which the chip is connected
> -- gpios: gpios the chip is connected to
> - first one is the interrupt gpio and second one the reset gpio
> +- rst-gpio: reset gpio the chip is connected to
> - x-size: horizontal resolution of touchscreen
> - y-size: vertical resolution of touchscreen
>
> Optional properties:
> +- int-gpio : interrupt gpio the chip is connected to
> - vdd-supply: Regulator controlling the controller supply
>
> Example:
> @@ -23,8 +23,8 @@ Example:
> interrupts = <2 0>;
> vdd-supply = <®_zforce_vdd>;
>
> - gpios = <&gpio5 6 0>, /* INT */
> - <&gpio5 9 0>; /* RST */
> + rst-gpio = <&gpio5 9 0>; /* RST */
> + int-gpio = <&gpio5 6 0>; /* INT, optional */
>
> x-size = <800>;
> y-size = <600>;
> diff --git a/drivers/input/touchscreen/zforce_ts.c
> b/drivers/input/touchscreen/zforce_ts.c
> index edf01c3..bf1e944 100644
> --- a/drivers/input/touchscreen/zforce_ts.c
> +++ b/drivers/input/touchscreen/zforce_ts.c
> @@ -494,6 +494,7 @@ static irqreturn_t zforce_irq_thread(int irq, void
> *dev_id)
> int ret;
> u8 payload_buffer[FRAME_MAXSIZE];
> u8 *payload;
> + int run = 1;
>
> /*
> * When still suspended, return.
> @@ -510,7 +511,18 @@ static irqreturn_t zforce_irq_thread(int irq, void
> *dev_id)
> if (!ts->suspending && device_may_wakeup(&client->dev))
> pm_stay_awake(&client->dev);
>
> - while (gpiod_get_value_cansleep(ts->gpio_int)) {
> + while (run) {
> + /*
> + * Exit the loop if either
> + * - the optional interrupt GPIO isn't specified
> + * (there is only one packet read per ISR invocation, then)
> + * or
> + * - the GPIO isn't active any more
> + * (packet read until the level GPIO indicates that there is
> + * no IRQ any more)
> + */
> + run = gpiod_get_value_cansleep(ts->gpio_int);
> +
> ret = zforce_read_packet(ts, payload_buffer);
> if (ret < 0) {
> dev_err(&client->dev,
> @@ -754,6 +766,40 @@ static int zforce_probe(struct i2c_client *client,
> if (!ts)
> return -ENOMEM;
>
> + /*
> + * The reset GPIO isn't optional, but we might get it
> + * via the old style DT entries below, too. So it's
> + * not an error if we don't get it here. Therefore use
> + * devm_gpiod_get_optional() here.
> + */
> + ts->gpio_rst = devm_gpiod_get_optional(&client->dev, "rst",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(ts->gpio_rst)) {
> + ret = PTR_ERR(ts->gpio_rst);
> + dev_err(&client->dev,
> + "failed to request reset GPIO: %d\n", ret);
> + return ret;
> + }
> +
> + ts->gpio_int = devm_gpiod_get_optional(&client->dev, "int", GPIOD_IN);
> + if (IS_ERR(ts->gpio_int)) {
> + ret = PTR_ERR(ts->gpio_int);
> + dev_err(&client->dev,
> + "failed to request interrupt GPIO: %d\n", ret);
> + return ret;
> + }
> +
> + /* Skip the old style GPIO if we have the new one */
> + if (ts->gpio_rst)
> + goto skip;
> +
> + /*
> + * Depreciated GPIO device tree handling for compatibility
> + * with existing device trees. For new device trees, don't
> + * use it any more. Instead use rst-gpio and the optional
> + * int-gpio above.
> + */
> +
> /* INT GPIO */
> ts->gpio_int = devm_gpiod_get_index(&client->dev, NULL, 0, GPIOD_IN);
> if (IS_ERR(ts->gpio_int)) {
> @@ -773,6 +819,7 @@ static int zforce_probe(struct i2c_client *client,
> return ret;
> }
>
> +skip:
> ts->reg_vdd = devm_regulator_get_optional(&client->dev, "vdd");
> if (IS_ERR(ts->reg_vdd)) {
> ret = PTR_ERR(ts->reg_vdd);
> --
> 2.3.4
>
--
Dmitry
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
