On Sun, Nov 15, 2015 at 04:56:43PM +0100, Sander Vermin wrote:
> This patch improves the pixcir_i2c_ts touchscreen controller which is used by
> the POV PROTAB2 tablet.
>
> On POV PROTAB2 tablet the WAKE and ENABLE gpios are used, and the screen is
> rotated, so touchscreen-inverted-x and touchscreen-inverted-y are needed.
>
> In this patch the WAKE and ENABLE gpios are implemented and furtermore the
> touchscreen-inverted-x/y and touchscreen-swapped-x-y devicetree options are
> implemented.
Need to fix the line wrapping.
>
> Signed-off-by: Sander Vermin <san...@vermin.nl>
> ---
> .../bindings/input/touchscreen/pixcir_i2c_ts.txt | 24 ++--
> drivers/input/touchscreen/pixcir_i2c_ts.c | 125
> +++++++++++++++++++--
> 2 files changed, 135 insertions(+), 14 deletions(-)
>
> diff --git
> a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt
> b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt
> index 8eb240a..5f25e96 100644
> --- a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt
> +++ b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt
> @@ -1,15 +1,25 @@
> * Pixcir I2C touchscreen controllers
>
> Required properties:
> -- compatible: must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc"
> -- reg: I2C address of the chip
> -- interrupts: interrupt to which the chip is connected
> -- attb-gpio: GPIO connected to the ATTB line of the chip
> -- touchscreen-size-x: horizontal resolution of touchscreen (in pixels)
> -- touchscreen-size-y: vertical resolution of touchscreen (in pixels)
> +- compatible : must be "pixcir,pixcir_ts" or "pixcir,pixcir_tangoc"
> +- reg : I2C address of the chip
> +- interrupts : interrupt to which the chip is connected
> +- attb-gpio : GPIO connected to the ATTB line of the chip
> +- touchscreen-size-x : horizontal resolution of touchscreen (in pixels)
> +- touchscreen-size-y : vertical resolution of touchscreen (in pixels)
Please do reformatting in a separate patch.
> Optional properties:
> -- reset-gpio: GPIO connected to the RESET line of the chip
> +- reset-gpio : GPIO connected to the RESET line of the chip
> +- enable-gpios : GPIO connected to the ENABLE line of the chip
> +- wake-gpios : GPIO connected to the WAKE line of the chip
> +- touchscreen-fuzz-x : horizontal noise value of the absolute input
> + device (in pixels)
> +- touchscreen-fuzz-y : vertical noise value of the absolute input
> + device (in pixels)
> +- touchscreen-inverted-x: X axis is inverted (boolean)
> +- touchscreen-inverted-y: Y axis is inverted (boolean)
> +- touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
> + Swapping is done after inverting the axis
Adding these touchscreen properties are not mentioned in the subject.
>
> Example:
>
> diff --git a/drivers/input/touchscreen/pixcir_i2c_ts.c
> b/drivers/input/touchscreen/pixcir_i2c_ts.c
> index 4b961ad..87f86b5 100644
> --- a/drivers/input/touchscreen/pixcir_i2c_ts.c
> +++ b/drivers/input/touchscreen/pixcir_i2c_ts.c
> @@ -38,6 +38,13 @@ struct pixcir_i2c_ts_data {
> struct input_dev *input;
> struct gpio_desc *gpio_attb;
> struct gpio_desc *gpio_reset;
> + struct gpio_desc *gpio_enable;
> + struct gpio_desc *gpio_wake;
> + u32 max_x;
> + u32 max_y;
> + bool invert_x;
> + bool invert_y;
> + bool swap_x_y;
> const struct pixcir_i2c_chip_data *chip;
> int max_fingers; /* Max fingers supported in this instance */
> bool running;
> @@ -146,12 +153,27 @@ static void pixcir_ts_report(struct pixcir_i2c_ts_data
> *ts,
> slot = slots[i];
> }
>
> + if (ts->invert_x)
> + touch->x = ts->max_x - touch->x;
> +
> + if (ts->invert_y)
> + touch->y = ts->max_y - touch->y;
> +
> input_mt_slot(ts->input, slot);
> input_mt_report_slot_state(ts->input,
> MT_TOOL_FINGER, true);
>
> - input_event(ts->input, EV_ABS, ABS_MT_POSITION_X, touch->x);
> - input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y, touch->y);
> + if (!ts->swap_x_y) {
> + input_event(ts->input, EV_ABS, ABS_MT_POSITION_X,
> + touch->x);
> + input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y,
> + touch->y);
> + } else {
> + input_event(ts->input, EV_ABS, ABS_MT_POSITION_X,
> + touch->y);
> + input_event(ts->input, EV_ABS, ABS_MT_POSITION_Y,
> + touch->x);
> + }
>
> dev_dbg(dev, "%d: slot %d, x %d, y %d\n",
> i, slot, touch->x, touch->y);
> @@ -194,6 +216,7 @@ static irqreturn_t pixcir_ts_isr(int irq, void *dev_id)
> static void pixcir_reset(struct pixcir_i2c_ts_data *tsdata)
> {
> if (!IS_ERR_OR_NULL(tsdata->gpio_reset)) {
> + /* toggle reset pin */
> gpiod_set_value_cansleep(tsdata->gpio_reset, 1);
> ndelay(100); /* datasheet section 1.2.3 says 80ns min. */
> gpiod_set_value_cansleep(tsdata->gpio_reset, 0);
> @@ -208,6 +231,14 @@ static int pixcir_set_power_mode(struct
> pixcir_i2c_ts_data *ts,
> struct device *dev = &ts->client->dev;
> int ret;
>
> + if (mode == PIXCIR_POWER_ACTIVE || mode == PIXCIR_POWER_IDLE) {
> + if (!IS_ERR_OR_NULL(ts->gpio_wake)) {
> + /* set wake pin */
> + gpiod_set_value_cansleep(ts->gpio_wake, 1);
> + dev_info(dev, "SET POWER: Set wake pin HIGH\n");
> + }
> + }
> +
> ret = i2c_smbus_read_byte_data(ts->client, PIXCIR_REG_POWER_MODE);
> if (ret < 0) {
> dev_err(dev, "%s: can't read reg 0x%x : %d\n",
> @@ -228,6 +259,14 @@ static int pixcir_set_power_mode(struct
> pixcir_i2c_ts_data *ts,
> return ret;
> }
>
> + if (mode == PIXCIR_POWER_HALT) {
> + if (!IS_ERR_OR_NULL(ts->gpio_wake)) {
> + /* set wake pin */
> + gpiod_set_value_cansleep(ts->gpio_wake, 0);
> + dev_info(dev, "SET POWER: Set wake pin LOW\n");
> + }
> + }
> +
> return 0;
> }
>
> @@ -302,6 +341,14 @@ static int pixcir_start(struct pixcir_i2c_ts_data *ts)
> struct device *dev = &ts->client->dev;
> int error;
>
> + if (!IS_ERR_OR_NULL(ts->gpio_enable)) {
> + /* set enable pin */
> + gpiod_set_value_cansleep(ts->gpio_enable, 1);
> + dev_info(dev, "START: Set enable pin HIGH\n");
> + }
> +
> + msleep(100);
> +
> /* LEVEL_TOUCH interrupt with active low polarity */
> error = pixcir_set_int_mode(ts, PIXCIR_INT_LEVEL_TOUCH, 0);
> if (error) {
> @@ -325,6 +372,7 @@ static int pixcir_start(struct pixcir_i2c_ts_data *ts)
>
> static int pixcir_stop(struct pixcir_i2c_ts_data *ts)
> {
> + struct device *dev = &ts->client->dev;
> int error;
>
> /* Disable interrupt generation */
> @@ -343,6 +391,12 @@ static int pixcir_stop(struct pixcir_i2c_ts_data *ts)
> /* Wait till running ISR is complete */
> synchronize_irq(ts->client->irq);
>
> + if (!IS_ERR_OR_NULL(ts->gpio_enable)) {
> + /* set enable pin */
> + gpiod_set_value_cansleep(ts->gpio_enable, 0);
> + dev_info(dev, "STOP: Set enable pin LOW\n");
> + }
> +
> return 0;
> }
>
> @@ -425,6 +479,7 @@ static int pixcir_parse_dt(struct device *dev,
> struct pixcir_i2c_ts_data *tsdata)
> {
> const struct of_device_id *match;
> + struct device_node *np = dev->of_node;
>
> match = of_match_device(of_match_ptr(pixcir_of_match), dev);
> if (!match)
> @@ -433,7 +488,12 @@ static int pixcir_parse_dt(struct device *dev,
> tsdata->chip = (const struct pixcir_i2c_chip_data *)match->data;
> if (!tsdata->chip)
> return -EINVAL;
> -
> +
> + /* Optional device tree properties */
> + tsdata->swap_x_y = of_property_read_bool(np, "touchscreen-swapped-x-y");
> + tsdata->invert_x = of_property_read_bool(np, "touchscreen-inverted-x");
> + tsdata->invert_y = of_property_read_bool(np, "touchscreen-inverted-y");
> +
> return 0;
> }
> #else
> @@ -490,19 +550,37 @@ static int pixcir_i2c_ts_probe(struct i2c_client
> *client,
> input->dev.parent = &client->dev;
>
> if (pdata) {
> - input_set_abs_params(input, ABS_MT_POSITION_X, 0, pdata->x_max,
> 0, 0);
> - input_set_abs_params(input, ABS_MT_POSITION_Y, 0, pdata->y_max,
> 0, 0);
> + if (!tsdata->swap_x_y) {
> + input_set_abs_params(input, ABS_MT_POSITION_X, 0,
> + pdata->x_max, 0, 0);
> + input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
> + pdata->y_max, 0, 0);
> + } else {
> + input_set_abs_params(input, ABS_MT_POSITION_X, 0,
> + pdata->y_max, 0, 0);
> + input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
> + pdata->x_max, 0, 0);
> + }
> } else {
> input_set_capability(input, EV_ABS, ABS_MT_POSITION_X);
> input_set_capability(input, EV_ABS, ABS_MT_POSITION_Y);
> touchscreen_parse_properties(input, true);
> - if (!input_abs_get_max(input, ABS_MT_POSITION_X) ||
> - !input_abs_get_max(input, ABS_MT_POSITION_Y)) {
> + tsdata->max_x = input_abs_get_max(input, ABS_MT_POSITION_X);
> + tsdata->max_y = input_abs_get_max(input, ABS_MT_POSITION_Y);
> + if (!tsdata->max_x || !tsdata->max_y) {
> dev_err(dev, "Touchscreen size is not specified\n");
> return -EINVAL;
> }
> + if (tsdata->swap_x_y) {
> + input_set_abs_params(input, ABS_MT_POSITION_X, 0,
> + tsdata->max_y, 0, 0);
> + input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
> + tsdata->max_x, 0, 0);
> + }
> }
>
> +
> +
> tsdata->max_fingers = tsdata->chip->max_fingers;
> if (tsdata->max_fingers > PIXCIR_MAX_SLOTS) {
> tsdata->max_fingers = PIXCIR_MAX_SLOTS;
> @@ -534,6 +612,24 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
> return error;
> }
>
> + tsdata->gpio_wake = devm_gpiod_get(dev, "wake",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(tsdata->gpio_wake)) {
> + error = PTR_ERR(tsdata->gpio_wake);
> + if (error != -EPROBE_DEFER)
> + dev_err(dev, "Failed to request wake gpio: %d\n",
> error);
> + return error;
> + }
> +
> + tsdata->gpio_enable = devm_gpiod_get(dev, "enable",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(tsdata->gpio_enable)) {
> + error = PTR_ERR(tsdata->gpio_enable);
> + if (error != -EPROBE_DEFER)
> + dev_err(dev, "Failed to request enable gpio: %d\n",
> error);
> + return error;
> + }
> +
> error = devm_request_threaded_irq(dev, client->irq, NULL, pixcir_ts_isr,
> IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
> client->name, tsdata);
> @@ -542,6 +638,21 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
> return error;
> }
>
> +
> + if (!IS_ERR_OR_NULL(tsdata->gpio_enable)) {
> + /* set enable pin */
> + gpiod_set_value_cansleep(tsdata->gpio_enable, 1);
> + dev_info(dev, "PROBE: Set enable pin HIGH\n");
> + }
> +
> + if (!IS_ERR_OR_NULL(tsdata->gpio_wake)) {
> + /* set wake pin */
> + gpiod_set_value_cansleep(tsdata->gpio_wake, 1);
> + dev_info(dev, "PROBE: Set wake pin HIGH\n");
> + }
> +
> + msleep(100);
> +
> pixcir_reset(tsdata);
>
> /* Always be in IDLE mode to save power, device supports auto wake */
> --
> 2.5.0
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-ker...@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
To unsubscribe from this list: send the line "unsubscribe linux-input" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
