Hi, I'm having a problem communicating with a nokia 6210 over irda using a girbil dongle. I'm using a 2.4.4 kernel on a SuSE 7.2 distribution. The phone is recognised ok but I cannot get a response from it. I've tested it under Windows 98 and I can dial into my ISP fine (I have to set the speed to 9600 to get this to work).
When I run irattach I get the following > /etc/init.d/irda start Sep 24 20:38:18 thegimp kernel: IrDA: Registered device irda0 Sep 24 20:38:19 thegimp irattach: executing: 'echo 1 > /proc/sys/net/irda/discovery' Sep 24 20:38:20 thegimp irattach: Starting device irda0 Sep 24 20:38:20 thegimp kernel: irlmp_register_client() Sep 24 20:38:20 thegimp kernel: irtty_net_open() Sep 24 20:38:20 thegimp kernel: irlap_change_speed(), setting speed to 9600 Sep 24 20:38:20 thegimp irattach: executing: 'echo thegimp > /proc/sys/net/irda/devname' My irdadump shows that the phone is being found > irdadump 20:36:08.848683 xid:cmd 19064e06 > ffffffff S=6 s=0 (14) 20:36:08.938683 xid:cmd 19064e06 > ffffffff S=6 s=1 (14) 20:36:09.028683 xid:cmd 19064e06 > ffffffff S=6 s=2 (14) 20:36:09.118683 xid:cmd 19064e06 > ffffffff S=6 s=3 (14) 20:36:09.108683 xid:rsp 19064e06 < 114b0000 S=6 s=2 Nokia 6210 hint=b125 [ PnP Modem Fax Telephony IrCOMM IrOBEX ] (27) 20:36:09.208683 xid:cmd 19064e06 > ffffffff S=6 s=4 (14) 20:36:09.298683 xid:cmd 19064e06 > ffffffff S=6 s=5 (14) 20:36:09.388683 xid:cmd 19064e06 > ffffffff S=6 s=* thegimp hint=0400 [ Computer ] (23) > cat /proc/net/irda/discovery IrLMP: Discovery log: nickname: Nokia 6210, hint: 0xb125, saddr: 0x19064e06, daddr: 0x114b0000 But when I run wvdial the following happens > wvdial --> WvDial: Internet dialer version 1.41 --> Initializing modem. --> Sending: ATZ Sep 24 20:38:33 thegimp kernel: IrCOMM protocol (Dag Brattli) Sep 24 20:38:33 thegimp kernel: ircomm_tty_attach_cable() Sep 24 20:38:33 thegimp kernel: ircomm_tty_ias_register() Sep 24 20:38:33 thegimp kernel: irlmp_register_client() Sep 24 20:38:33 thegimp kernel: irlap_change_speed(), setting speed to 115200 Sep 24 20:38:37 thegimp kernel: IrLAP, no activity on link! --> Sending: ATQ0 --> Re-Sending: ATZ Sep 24 20:38:38 thegimp kernel: irlmp_state_setup() WATCHDOG_TIMEOUT! --> Modem not responding. Sep 24 20:38:46 thegimp kernel: irlap_change_speed(), setting speed to 9600 Sep 24 20:38:46 thegimp kernel: ircomm_tty_close() Sep 24 20:38:46 thegimp kernel: ircomm_tty_shutdown() Sep 24 20:38:46 thegimp kernel: ircomm_tty_detach_cable() Sep 24 20:38:46 thegimp kernel: ircomm_close() I think the modules that I need are all loaded > lsmod Module Size Used by ircomm-tty 31568 0 (autoclean) ircomm 14304 0 (autoclean) [ircomm-tty] af_packet 11584 0 (autoclean) irtty 7568 2 (autoclean) irda 146224 1 (autoclean) [ircomm-tty ircomm irtty] [snip] I'm setting the speed in wvdial to 9600 so why does this happen? Sep 24 20:38:33 thegimp kernel: irlap_change_speed(), setting speed to 115200 Can anyone see where the problem is? Thanks, Gareth. _______________________________________________ Linux-IrDA mailing list - [EMAIL PROTECTED] http://www.pasta.cs.UiT.No/mailman/listinfo/linux-irda
