on 15/11/2000 11:56, Garst R. Reese at [EMAIL PROTECTED] typed:
>
>
> Guy Plunkett wrote:
>>
>> on 15/11/2000 08:32, Garst R. Reese at [EMAIL PROTECTED] typed:
>>
>>>
>>>
>>> Jonathan Hudson wrote:
>>>>
>>>> In article <[EMAIL PROTECTED]>,
>>>> Guy Plunkett <[EMAIL PROTECTED]> writes:
>>>> GP>
>>>> GP> Thanks for the information....
>>>> GP>
>>>> GP> I'm downloading linux-2.4.0-test10.tar.gz kernel source..
>>>> GP>
>>>> GP> Can you point me in the direction of any and all patches that I
>>> should apply
>>>> GP> to get the IRDA working?
>>>>
>>>> I find test11-pre4 (the latest pre test 11) works just fine; modulo
>>>> any compilation problems listed here for hardware I don't have :)
>>>>
>>>> _______________________________________________
>>>> Linux-IrDA mailing list - [EMAIL PROTECTED]
>>>> http://www.pasta.cs.UiT.No/mailman/listinfo/linux-irda
>>> After much discussion the IrDA patches went into test11-pre3 and bugs
>>> were fixed
>>> in test11-pre4. Nothing earlier works.
>>> The patches are in kernel/testing.
>>> Garst
>>> _______________________________________________
>>> Linux-IrDA mailing list - [EMAIL PROTECTED]
>>> http://www.pasta.cs.UiT.No/mailman/listinfo/linux-irda
>>>
>>
>> Ok here's the story so far.....
>>
>> I've downloaded linux-2.4.0-test10.tgz
>> I've extracted and patched with test11-pre3.gz all works ok... no errors
> :-)
>>
>> I run make xconfig:
>> Code maturity level: Yes
>> Realtek TRL-8139 PCI fast ethernet Adapter Support: Yes
>> IRDA subsystem support: M
>> IRLan Protocol: N
>> IRNet Protocol: N
>> IRComm Protocol: M
>> Ultra: N
>> IRDA Protocol options: N
>> Irtty: M
>> IrPort: M
>>
>> Everything else as defaults
>>
>> make dep
>> make bzImage
>> make modules
>> make modules_install
>> - have to edit makefile so that -F is -m for the system.map
>>
>> I then copy the Sytem.map file to /boot/System.map-2.4.0-test11
>>
>> I configure lilo using linuxconf...
>> all goes well..I've done this a few times now and previously works
> fine
>>
>> However with this kernel...
>>
>> I select it at the boot prompt. and it loads the kernel and then
> freezes...
>>
>> Any ideas????
>>
>> please all I want to do is be able to ir link my palm the hotsync
>>
>> Thanks
> test11-pre3 isn't all the way working.
> try pre5. You have to back-out pre3 before applying pre5.
> But, pre4 and pre5 screwed up my apm with X and some apps running.
> Garst
> _______________________________________________
> Linux-IrDA mailing list - [EMAIL PROTECTED]
> http://www.pasta.cs.UiT.No/mailman/listinfo/linux-irda
>
Hello...
just patch for pre5...
configured as before... but I get the same problem
LILO boot: linux-2.4.0
Loading linux-2.4.0....................
Uncompressing Linux... Ok, booting the kernel.
Then nothing... the computer just sits there...
Any ideas???
Thanks
-- Guy
------------------------------------------
Guy Plunkett Bsc (Hons), CLP ICQ:61446480
Systems Support Engineer --> Mac, UNIX, PC
ABC Solutions -> http://www.abcworks.co.uk
Tel: +441582 461040 -- Fax: +441582 461742
_______________________________________________
Linux-IrDA mailing list - [EMAIL PROTECTED]
http://www.pasta.cs.UiT.No/mailman/listinfo/linux-irda
