This is bad. I am seeing problems as well, but speed=2 and even speed=4
are working here non 2.2.18 with both CDRW and CD-RW/DVD Ram. You may
have a hardware problem of some type, or perhaps the bug is more easily
reproducable for you. I have noticed that perhaps some of the problem
is in cdrecord itself, since I have seen that if the FIFO ever hits 0%
during CD burning, cdrecord has a tendency to bomb.
Forward to Andre([EMAIL PROTECTED]) and/or Jens Axboe ([EMAIL PROTECTED])
-- they both seem to be o top of this problem and are getting out fixes
for it.
:-)
Jeff
Mark Cooke wrote:
>
> Hi all,
>
> Just to follow up on an earlier message / thread. I've updated to
> 2.2.18pre15 on the machine (dual celeron, gigabyte 6bxd) I was having
> trouble writing CDRWs to, and it has made no difference,
> unfortunately.
>
> With the same tools / os on my other cdrw equipped machine
> (k7/up/ricoh 9060) the very same CDRW will blank perfectly happily.
>
> Both machines have the CDRW as the sole device on the second
> ide-chain.
>
> Using xcdrgtk's blank cd option which uses cdrecord 1.8.1 on the
> failed machine gives the following log. Using speed=1 or spped=2
> makes no difference to the error reported.
>
> Cdrecord 1.8.1 (i686-pc-linux-gnu) Copyright (C) 1995-2000 Jörg
> Schilling
> TOC Type: 1 = CD-ROM
> scsidev: '1,0,0'
> scsibus: 1 target: 0 lun: 0
> Using libscg version 'schily-0.1'
> atapi: 1
> Device type : Removable CD-ROM
> Version : 0
> Response Format: 1
> Vendor_info : 'HP '
> Identifikation : 'CD-Writer+ 7100 '
> Revision : '3.01'
> Device seems to be: Generic mmc CD-RW.
> Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
> Driver flags : SWABAUDIO
> Drive buf size : 786432 = 768 KB
> Current Secsize: 2048
> ATIP start of lead in: -11637 (97:26/63)
> ATIP start of lead out: 337350 (75:00/00)
> Disk type: phase change
> Manuf. index: 3
> Manufacturer: CMC Magnetics Corporation
> Blocks total: 337350 Blocks current: 337350 Blocks remaining: 337500
> Starting to write CD/DVD at speed 2 in write mode for single session.
>
> Blanking entire disk
> CDB: A1 00 00 00 00 00 00 00 00 00 00 00
> cdrecord: Input/output error. blank unit: scsi sendcmd: retryable error
> Sense Bytes: F0 00 05 00 00 00 00 19 00 02 89 16 A1 10 00 80
> status: 0x2 (CHECK CONDITION)
> Sense Key: 0x5 Illegal Request, Segment 0
> cdrecord: Cannot blank disk, aborting.
> Sense Code: 0xA1 Qual 0x10 (vendor unique sense code 0xA1) [No matching qualifier]
>Fru 0x0
> Sense flags: Blk 0 (valid) error refers to data part, bit ptr 0 (not valid) field
>ptr 0
> cmd finished after 13.218s timeout 9600s
>
> Anyone have any ideas?
>
> Mark
>
> --
> +-------------------------------------------------------------------------+
> Mark Cooke The views expressed above are mine and are not
> Systems Programmer necessarily representative of university policy
> University Of Birmingham URL: http://www.sr.bham.ac.uk/~mpc/
> +-------------------------------------------------------------------------+
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to [EMAIL PROTECTED]
> Please read the FAQ at http://www.tux.org/lkml/
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [EMAIL PROTECTED]
Please read the FAQ at http://www.tux.org/lkml/
