On Wed, Nov 18, 2015 at 09:51:48PM +0100, Josef Gajdusek wrote:
> This patch adds support for the Sunxi thermal sensor on the Allwinner H3.
> Also adds declaration of the H3 THS clock to clk-sunxi.c ignoring the
> dividers as they are not continuous (clk-divider.c cannot be used as it
> does not support setting an enable bit).
> Should be easily extendable for the A33/A83T/... as they have similar but
> not completely identical sensors.
>
> Signed-off-by: Josef Gajdusek <a...@atx.name>
> ---
> Documentation/devicetree/bindings/clock/sunxi.txt | 1 +
> .../devicetree/bindings/thermal/sunxi-ths.txt | 24 ++
> arch/arm/boot/dts/sun8i-h3.dtsi | 27 +++
> drivers/clk/sunxi/clk-sunxi.c | 16 ++
> drivers/thermal/Kconfig | 7 +
> drivers/thermal/Makefile | 1 +
> drivers/thermal/sunxi_ths.c | 263
> +++++++++++++++++++++
> 7 files changed, 339 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/thermal/sunxi-ths.txt
> create mode 100644 drivers/thermal/sunxi_ths.c
>
> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt
> b/Documentation/devicetree/bindings/clock/sunxi.txt
> index 23e7bce..6d63b35 100644
> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
> @@ -73,6 +73,7 @@ Required properties:
> "allwinner,sun8i-h3-usb-clk" - for usb gates + resets on H3
> "allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80
> "allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80
> + "allwinner,sun8i-h3-ths-clk" - for THS on H3
>
> Required properties for all clocks:
> - reg : shall be the control register address for the clock.
> diff --git a/Documentation/devicetree/bindings/thermal/sunxi-ths.txt
> b/Documentation/devicetree/bindings/thermal/sunxi-ths.txt
> new file mode 100644
> index 0000000..75c9211
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/thermal/sunxi-ths.txt
> @@ -0,0 +1,24 @@
> +* sunxi THS
> +
> +Required properties:
> +- compatible : "allwinner,sun8i-h3-ths"
> +- reg : Address range of the thermal registers and location of the
> calibration
> + value
> +- resets : Must contain an entry for each entry in reset-names.
> + see ../reset/reset.txt for details
> +- reset-names : Must include the name "ahb"
> +- clocks : Must contain an entry for each entry in clock-names.
> +- clock-names : Must contain "ahb" for the bus gate and "ths" for the THS
> + clock
> +
> +Example:
> +ths: ths@01c25000 {
> + #thermal-sensor-cells = <0>;
> + compatible = "allwinner,sun8i-h3-ths";
> + reg = <0x01c25000 0x88>, <0x01c14234 0x4>;
> + interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
> + resets = <&bus_rst 136>;
> + reset-names = "ahb";
> + clocks = <&bus_gates 72>, <&ths_clk>;
> + clock-names = "ahb", "ths";
> +};
> diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
> index 0faa38a..b82881d 100644
> --- a/arch/arm/boot/dts/sun8i-h3.dtsi
> +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
> @@ -77,6 +77,14 @@
> };
> };
>
> + thermal-zones {
> + cpu_thermal: cpu_thermal {
> + polling-delay-passive = <1000>;
> + polling-delay = <5000>;
> + thermal-sensors = <&ths 0>;
> + };
> + };
> +
> timer {
> compatible = "arm,armv7-timer";
> interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
> IRQ_TYPE_LEVEL_LOW)>,
> @@ -236,6 +244,14 @@
> "ahb1_ephy", "ahb1_dbg";
> };
>
> + ths_clk: clk@01c20074 {
> + #clock-cells = <0>;
> + compatible = "allwinner,sun8i-h3-ths-clk";
> + reg = <0x01c20074 0x4>;
> + clocks = <&osc24M>;
> + clock-output-names = "ths";
> + };
> +
> mmc0_clk: clk@01c20088 {
> #clock-cells = <1>;
> compatible = "allwinner,sun4i-a10-mmc-clk";
> @@ -522,6 +538,17 @@
> interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
> };
>
> + ths: ths@01c25000 {
> + #thermal-sensor-cells = <0>;
> + compatible = "allwinner,sun8i-h3-ths";
> + reg = <0x01c25000 0x88>, <0x01c14234 0x4>;
> + interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
> + resets = <&bus_rst 104>;
> + reset-names = "ahb";
> + clocks = <&bus_gates 72>, <&ths_clk>;
> + clock-names = "ahb", "ths";
> + };
> +
> uart0: serial@01c28000 {
> compatible = "snps,dw-apb-uart";
> reg = <0x01c28000 0x400>;
> diff --git a/drivers/clk/sunxi/clk-sunxi.c b/drivers/clk/sunxi/clk-sunxi.c
> index 6293c65..637401a 100644
> --- a/drivers/clk/sunxi/clk-sunxi.c
> +++ b/drivers/clk/sunxi/clk-sunxi.c
> @@ -604,6 +604,13 @@ static void sun7i_a20_get_out_factors(u32 *freq, u32
> parent_rate,
> *p = calcp;
> }
>
> +static void sun8i_h3_get_ths_factors(u32 *freq, u32 parent_rate,
> + u8 *n, u8 *k, u8 *m, u8 *p)
> +{
> + /* Ignore the dividers as they are not continuous */
> + *freq = parent_rate;
> +}
> +
> /**
> * sunxi_factors_clk_setup() - Setup function for factor clocks
> */
> @@ -668,6 +675,8 @@ static struct clk_factors_config sun4i_apb1_config = {
> .pwidth = 2,
> };
>
> +static struct clk_factors_config sun8i_h3_ths_config = {};
> +
> /* user manual says "n" but it's really "p" */
> static struct clk_factors_config sun7i_a20_out_config = {
> .mshift = 8,
> @@ -734,6 +743,12 @@ static const struct factors_data sun7i_a20_out_data
> __initconst = {
> .getter = sun7i_a20_get_out_factors,
> };
>
> +static const struct factors_data sun8i_h3_ths_data __initconst = {
> + .enable = 31,
> + .table = &sun8i_h3_ths_config,
> + .getter = sun8i_h3_get_ths_factors,
> +};
> +
> static struct clk * __init sunxi_factors_clk_setup(struct device_node *node,
> const struct factors_data
> *data)
> {
> @@ -1127,6 +1142,7 @@ static const struct of_device_id clk_factors_match[]
> __initconst = {
> {.compatible = "allwinner,sun5i-a13-ahb-clk", .data =
> &sun5i_a13_ahb_data,},
> {.compatible = "allwinner,sun4i-a10-apb1-clk", .data =
> &sun4i_apb1_data,},
> {.compatible = "allwinner,sun7i-a20-out-clk", .data =
> &sun7i_a20_out_data,},
> + {.compatible = "allwinner,sun8i-h3-ths-clk", .data =
> &sun8i_h3_ths_data,},
> {}
> };
>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index c463c89..0111d4d 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -365,6 +365,13 @@ config INTEL_PCH_THERMAL
> Thermal reporting device will provide temperature reading,
> programmable trip points and other information.
>
> +config SUNXI_THS
> + tristate "Sunxi THS driver"
> + depends on ARCH_SUNXI
> + depends on OF
> + help
> + Enable this to support thermal reporting on some newer Allwinner SoC.
> +
> menu "Texas Instruments thermal drivers"
> depends on ARCH_HAS_BANDGAP || COMPILE_TEST
> source "drivers/thermal/ti-soc-thermal/Kconfig"
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index cfae6a6..3a25e3c 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -48,3 +48,4 @@ obj-$(CONFIG_INTEL_PCH_THERMAL) += intel_pch_thermal.o
> obj-$(CONFIG_ST_THERMAL) += st/
> obj-$(CONFIG_TEGRA_SOCTHERM) += tegra_soctherm.o
> obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
> +obj-$(CONFIG_SUNXI_THS) += sunxi_ths.o
> diff --git a/drivers/thermal/sunxi_ths.c b/drivers/thermal/sunxi_ths.c
> new file mode 100644
> index 0000000..650cd39
> --- /dev/null
> +++ b/drivers/thermal/sunxi_ths.c
> @@ -0,0 +1,263 @@
> +/*
> + * Sunxi THS driver
> + *
> + * Copyright (C) 2015 Josef Gajdusek
> + *
> + * This software is licensed under the terms of the GNU General Public
> + * License version 2, as published by the Free Software Foundation, and
> + * may be copied, distributed, and modified under those terms.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/irq.h>
I do not see any sign of irq in this code, so perhaps linux/irq.h and
linux/interrupt.h are useless.
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
...
> +struct sunxi_ths_data {
> + struct sunxi_ths_type *type;
> + struct reset_control *reset;
> + struct clk *clk;
> + struct clk *busclk;
> + void __iomem *regs;
> + void __iomem *calreg;
> + struct platform_device *pdev;
> + struct thermal_zone_device *tzd;
> + int irq;
/* This variable is never used */
> +};
> +
> +struct sunxi_ths_type {
> + int (*init)(struct sunxi_ths_data *);
> + int (*get_temp)(struct sunxi_ths_data *, int *out);
> +};
> +
> +static int sunxi_ths_reg_to_temperature(int32_t reg, int divisor, int minus)
> +{
> + return minus - (reg * 1000000) / divisor;
> +}
Use s32 instead of int32_t
Perhaps this is a sign that you do not have used checkpatch --strict
> +
> +static int sunxi_ths_get_temp(void *_data, int *out)
> +{
> + struct sunxi_ths_data *data = _data;
> +
> + return data->type->get_temp(data, out);
> +}
> +
> +static int sunxi_ths_h3_init(struct sunxi_ths_data *data)
> +{
> + if (data->calreg)
> + writel(readl(data->calreg) & 0xfff, data->regs + THS_H3_CDATA);
> + /* Magical constants mostly taken from Allwinner 3.4 kernel.
> + * Seem to work fine, though this could be configurable in DT/sysft
> + */
> + writel(0xff << THS_H3_CTRL0_SENSOR_ACQ0,
> + data->regs + THS_H3_CTRL0);
> + writel((0x3f << THS_H3_CTRL2_SENSOR_ACQ1) | BIT(THS_H3_CTRL2_SENSE_EN),
> + data->regs + THS_H3_CTRL2);
> + writel((0x390 << THS_H3_INT_CTRL_THERMAL_PER) |
> BIT(THS_H3_INT_CTRL_DATA_IRQ_EN),
> + data->regs + THS_H3_INT_CTRL);
> + writel(BIT(THS_H3_FILTER_EN) | (0x2 << THS_H3_FILTER_TYPE),
> + data->regs + THS_H3_FILTER);
> + return 0;
> +}
> +
> +static int sunxi_ths_h3_get_temp(struct sunxi_ths_data *data, int *out)
> +{
> + *out = sunxi_ths_reg_to_temperature(readl(data->regs + THS_H3_DATA),
> + 8253, 217000);
You could use a temp variable for avoiding this 80column wrap.
You could explain also from where 8253 and 217000 come from.
> + return 0;
> +}
> +
> +static const struct thermal_zone_of_device_ops sunxi_ths_thermal_ops = {
> + .get_temp = sunxi_ths_get_temp,
> +};
> +
> +static const struct sunxi_ths_type sunxi_ths_device_h3 = {
> + .init = sunxi_ths_h3_init,
> + .get_temp = sunxi_ths_h3_get_temp,
> +};
> +
> +static const struct of_device_id sunxi_ths_id_table[] = {
> + {
> + .compatible = "allwinner,sun8i-h3-ths",
> + .data = &sunxi_ths_device_h3,
> + },
> + {
> + /* sentinel */
> + },
> +};
> +MODULE_DEVICE_TABLE(of, sunxi_ths_id_table);
> +
> +static int sunxi_ths_probe(struct platform_device *pdev)
> +{
> + struct device_node *np = pdev->dev.of_node;
> + const struct of_device_id *match;
> + struct sunxi_ths_data *data;
> + struct resource *res;
> + int ret;
> +
> + match = of_match_node(sunxi_ths_id_table, np);
> + if (!match)
> + return -ENXIO;
I think -ENXIO is not the correct return code.
> +
> + data =
> + devm_kzalloc(&pdev->dev, sizeof(struct sunxi_ths_data),
> GFP_KERNEL);
Prefer sizeof(*data)
Again use checkpatch --strict
Regards
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
