From: Alex Smith <alex.sm...@imgtec.com>
Add DT bindings for NAND devices connected to the NEMC on JZ4780 SoCs,
as well as the hardware BCH controller, used by the jz4780_{nand,bch}
drivers.
Signed-off-by: Alex Smith <alex.sm...@imgtec.com>
Cc: Zubair Lutfullah Kakakhel <zubair.kakak...@imgtec.com>
Cc: David Woodhouse <dw...@infradead.org>
Cc: Brian Norris <computersforpe...@gmail.com>
Cc: linux-...@lists.infradead.org
Cc: devicet...@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Alex Smith <a...@alex-smith.me.uk>
Signed-off-by: Harvey Hunt <harvey.h...@imgtec.com>
---
v7 -> v8:
- Describe how NAND chips are now child nodes of the NAND controller.
v6 -> v7:
- Add nand-ecc-mode to DT bindings.
- Add nand-on-flash-bbt to DT bindings.
v5 -> v6:
- No change.
v4 -> v5:
- Rename ingenic,bch-device to ingenic,bch-controller to fit with
existing convention.
v3 -> v4:
- No change
v2 -> v3:
- Rebase to 4.0-rc6
- Changed ingenic,ecc-size to common nand-ecc-step-size
- Changed ingenic,ecc-strength to common nand-ecc-strength
- Changed ingenic,busy-gpio to common rb-gpios
- Changed ingenic,wp-gpio to common wp-gpios
v1 -> v2:
- Rebase to 4.0-rc3
.../bindings/mtd/ingenic,jz4780-nand.txt | 81 ++++++++++++++++++++++
1 file changed, 81 insertions(+)
create mode 100644
Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
diff --git a/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
new file mode 100644
index 0000000..8151602
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/ingenic,jz4780-nand.txt
@@ -0,0 +1,81 @@
+* Ingenic JZ4780 NAND/BCH
+
+This file documents the device tree bindings for NAND flash devices on the
+JZ4780. NAND devices are connected to the NEMC controller (described in
+memory-controllers/ingenic,jz4780-nemc.txt), and thus NAND device nodes must
+be children of the NEMC node.
+
+Required NAND controller device properties:
+- compatible: Should be set to "ingenic,jz4780-nand".
+- reg: For each bank with a NAND chip attached, should specify a bank number,
+ an offset of 0 and a size of 0x1000000 (i.e. the whole NEMC bank).
+
+Optional NAND controller device properties:
+- ingenic,bch-controller: To make use of the hardware BCH controller, this
+ property must contain a phandle for the BCH controller node. The required
+ properties for this node are described below. If this is not specified,
+ software BCH will be used instead.
+
+Optional children nodes:
+Individual NAND chips are children of the NAND controller node.
+
+Required children node properties:
+- reg: An integer ranging from 1 to 6 representing the CS line to use.
+- #address-cells: See partition.txt
+- #size-cells: See partition.txt
+
+Optional children node properties:
+- nand-ecc-step-size: ECC block size in bytes.
+- nand-ecc-strength: ECC strength (max number of correctable bits).
+- nand-ecc-mode: String, operation mode of the NAND ecc mode. "hw" by default
+- nand-on-flash-bbt: boolean to enable on flash bbt option, if not present
false
+- rb-gpios: GPIO specifier for the busy pin.
+- wp-gpios: GPIO specifier for the write protect pin.
+
+Example:
+
+nemc: nemc@13410000 {
+ ...
+
+ nandc: nand-controller@1 {
+ compatible = "ingenic,jz4780-nand";
+ reg = <1 0 0x1000000>; /* Bank 1 */
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ingenic,bch-controller = <&bch>;
+
+ nand@1 {
+ reg = <1>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ nand-ecc-step-size = <1024>;
+ nand-ecc-strength = <24>;
+ nand-ecc-mode = "hw";
+ nand-on-flash-bbt;
+
+ rb-gpios = <&gpa 20 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpf 22 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+The BCH controller is a separate SoC component used for error correction on
+NAND devices. The following is a description of the device properties for a
+BCH controller.
+
+Required BCH properties:
+- compatible: Should be set to "ingenic,jz4780-bch".
+- reg: Should specify the BCH controller registers location and length.
+- clocks: Clock for the BCH controller.
+
+Example:
+
+bch: bch@134d0000 {
+ compatible = "ingenic,jz4780-bch";
+ reg = <0x134d0000 0x10000>;
+
+ clocks = <&cgu JZ4780_CLK_BCH>;
+};
--
2.6.2
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
