Hi,
On 2015년 12월 10일 09:39, Krzysztof Kozlowski wrote:
> On 09.12.2015 13:07, Chanwoo Choi wrote:
>> This patch adds the documentation for generic exynos bus frequency
>> driver.
>>
>> Signed-off-by: Chanwoo Choi <cw00.c...@samsung.com>
>> ---
>> .../devicetree/bindings/devfreq/exynos-bus.txt | 94
>> ++++++++++++++++++++++
>> 1 file changed, 94 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/devfreq/exynos-bus.txt
>>
>> diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
>> b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
>> new file mode 100644
>> index 000000000000..54a1f9c46c88
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
>> @@ -0,0 +1,94 @@
>> +* Generic Exynos Bus frequency device
>> +
>> +The Samsung Exynos SoC have many buses for data transfer between DRAM
>> +and sub-blocks in SoC. Almost Exynos SoC have the common architecture
>> +for buses. Generally, the each bus of Exynos SoC includes the source clock
>> +and power line and then is able to change the clock according to the usage
>> +of each buses on runtime. When gathering the usage of each buses on runtime,
>> +thie driver uses the PPMU (Platform Performance Monitoring Unit) which
>
> s/thie/the/
OK.
>
>> +is able to measure the current load of sub-blocks.
>> +
>> +There are a little different composition among Exynos SoC because each
>> Exynos
>> +SoC has the different sub-blocks. So, this difference should be specified
>> +in devicetree file instead of each device driver. In result, this driver
>> +is able to support the bus frequency for all Exynos SoCs.
>> +
>> +Required properties for bus device:
>> +- compatible: Should be "samsung,exynos-bus".
>> +- clock-names : the name of clock used by the bus, "bus".
>> +- clocks : phandles for clock specified in "clock-names" property.
>> +- #clock-cells: should be 1.
>
> This is a clock consumer, right? So the clock-cells is not valid here.
You're right. I'll remove '#clock-cells'.
>
>> +- operating-points-v2: the OPP table including frequency/voltage information
>> + to support DVFS (Dynamic Voltage/Frequency Scaling) feature.
>> +- vdd-supply: the regulator to provide the buses with the voltage.
>> +- devfreq-events: the devfreq-event device to monitor the curret utilization
>
> s/curret/current/
>
>> + of buses.
>> +
>> +Optional properties for bus device:
>> +- exynos,saturation-ratio: the percentage value which is used to calibrate
>> + the performance count againt total cycle count.
>
> s/againt/against/
OK.
>
>> +
>> +Example1:
>> + Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to
>> + power line (regulator). The MIF (Memory Interface) AXI bus is used to
>> + transfer data between DRAM and CPU and uses the VDD_MIF regualtor.
>> +
>> + - power line(VDD_MIF) --> bus for DMC (Dynamic Memory Controller) block
>> +
>> + - MIF bus's frequency/voltage table
>> + -----------------------
>> + |Lv| Freq | Voltage |
>> + -----------------------
>> + |L1| 50000 |800000 |
>> + |L2| 100000 |800000 |
>> + |L3| 134000 |800000 |
>> + |L4| 200000 |800000 |
>> + |L5| 400000 |875000 |
>> + -----------------------
>> +
>> +Example2 :
>> + The bus of DMC (Dynamic Memory Controller) block in exynos3250.dtsi
>> + are listed below:
>
> s/are/is/ (one bus is listed)
OK.
>
>> +
>> + bus_dmc: bus_dmc {
>> + compatible = "samsung,exynos-bus";
>> + clocks = <&cmu_dmc CLK_DIV_DMC>;
>> + clock-names = "bus";
>> + operating-points-v2 = <&bus_dmc_opp_table>;
>> + status = "disabled";
>> + };
>> +
>> + bus_dmc_opp_table: opp_table0 {
>> + compatible = "operating-points-v2";
>> + opp-shared;
>> +
>> + opp00 {
>
> Maybe use convention with frequency, like:
> opp@50000000
> This also used in opp.txt examples.
In the Documentations/devicetree/bindings/opp/opp.txt,
the example uses the 'opp@0x'. I check the opp.txt of Linux 4.4-rc4.
>
>
>> + opp-hz = /bits/ 64 <50000000>;
>> + opp-microvolt = <800000>;
>> + };
>> + opp01 {
>> + opp-hz = /bits/ 64 <100000000>;
>> + opp-microvolt = <800000>;
>> + };
>> + opp02 {
>> + opp-hz = /bits/ 64 <134000000>;
>> + opp-microvolt = <800000>;
>> + };
>> + opp03 {
>> + opp-hz = /bits/ 64 <200000000>;
>> + opp-microvolt = <800000>;
>> + };
>> + opp04 {
>> + opp-hz = /bits/ 64 <400000000>;
>> + opp-microvolt = <875000>;
>> + };
>> + };
>> +
>> + Usage case to handle the frequency and voltage of bus on runtime
>> + in exynos3250-rinato.dts are listed below:
>
> s/are/is/
OK.
>
>> +
>> + &bus_dmc {
>> + devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
>> + vdd-supply = <&buck1_reg>; /* VDD_MIF */
>> + status = "okay";
>> + };
Thanks for your review.
Regards,
Chanwoo Choi
--
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
