The Amlogic Meson GXL should use the common GX dtsi as base.
Signed-off-by: Neil Armstrong <narmstr...@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 133 +----------------------------
1 file changed, 1 insertion(+), 132 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
index 2aa4555..16891e0 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
@@ -41,139 +41,8 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "meson-gx-common.dtsi"
/ {
compatible = "amlogic,meson-gxl";
- interrupt-parent = <&gic>;
- #address-cells = <2>;
- #size-cells = <2>;
-
- cpus {
- #address-cells = <0x2>;
- #size-cells = <0x0>;
-
- cpu0: cpu@0 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x0>;
- enable-method = "psci";
- };
-
- cpu1: cpu@1 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x1>;
- enable-method = "psci";
- };
-
- cpu2: cpu@2 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x2>;
- enable-method = "psci";
- };
-
- cpu3: cpu@3 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x3>;
- enable-method = "psci";
- };
- };
-
- arm-pmu {
- compatible = "arm,cortex-a53-pmu";
- interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
- };
-
- psci {
- compatible = "arm,psci-0.2";
- method = "smc";
- };
-
- timer {
- compatible = "arm,armv8-timer";
- interrupts = <GIC_PPI 13
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 14
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 11
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 10
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>;
- };
-
- xtal: xtal-clk {
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "xtal";
- #clock-cells = <0>;
- };
-
- soc {
- compatible = "simple-bus";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- cbus: cbus@c1100000 {
- compatible = "simple-bus";
- reg = <0x0 0xc1100000 0x0 0x100000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
-
- uart_A: serial@84c0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x084c0 0x0 0x14>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
- };
-
- gic: interrupt-controller@c4301000 {
- compatible = "arm,gic-400";
- reg = <0x0 0xc4301000 0 0x1000>,
- <0x0 0xc4302000 0 0x2000>,
- <0x0 0xc4304000 0 0x2000>,
- <0x0 0xc4306000 0 0x2000>;
- interrupt-controller;
- interrupts = <GIC_PPI 9
- (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
- #interrupt-cells = <3>;
- #address-cells = <0>;
- };
-
- aobus: aobus@c8100000 {
- compatible = "simple-bus";
- reg = <0x0 0xc8100000 0x0 0x100000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
-
- uart_AO: serial@4c0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x004c0 0x0 0x14>;
- interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
- };
-
- apb: apb@d0000000 {
- compatible = "simple-bus";
- reg = <0x0 0xd0000000 0x0 0x200000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
- };
- };
};
--
1.9.1
