- add a title for the document;
- convert some parameters to tables;
- use quote blocks where needed;
- use monotonic fonts for parameters;
- adjust whitespaces and blank lines;
- add it to the user's book.

Signed-off-by: Mauro Carvalho Chehab <mche...@s-opensource.com>
---
 Documentation/md.txt         | 528 ++++++++++++++++++++++++++-----------------
 Documentation/user/index.rst |   1 +
 Documentation/user/md.rst    |   1 +
 3 files changed, 323 insertions(+), 207 deletions(-)
 create mode 120000 Documentation/user/md.rst

diff --git a/Documentation/md.txt b/Documentation/md.txt
index d6e2fcf27337..e449fb5f277c 100644
--- a/Documentation/md.txt
+++ b/Documentation/md.txt
@@ -1,42 +1,77 @@
-Tools that manage md devices can be found at
-   http://www.kernel.org/pub/linux/utils/raid/ 
-
+RAID arrays
+===========
 
 Boot time assembly of RAID arrays
 ---------------------------------
 
+Tools that manage md devices can be found at
+   http://www.kernel.org/pub/linux/utils/raid/
+
+
 You can boot with your md device with the following kernel command
 lines:
 
-for old raid arrays without persistent superblocks:
+for old raid arrays without persistent superblocks::
+
   md=<md device no.>,<raid level>,<chunk size factor>,<fault 
level>,dev0,dev1,...,devn
 
-for raid arrays with persistent superblocks
+for raid arrays with persistent superblocks::
+
   md=<md device no.>,dev0,dev1,...,devn
-or, to assemble a partitionable array:
+
+or, to assemble a partitionable array::
+
   md=d<md device no.>,dev0,dev1,...,devn
-  
-md device no. = the number of the md device ... 
-              0 means md0, 
-             1 md1,
-             2 md2,
-             3 md3,
-             4 md4
-
-raid level = -1 linear mode
-              0 striped mode
-             other modes are only supported with persistent super blocks
-
-chunk size factor = (raid-0 and raid-1 only)
-              Set  the chunk size as 4k << n.
-             
-fault level = totally ignored
-                           
-dev0-devn: e.g. /dev/hda1,/dev/hdc1,/dev/sda1,/dev/sdb1
-                           
-A possible loadlin line (Harald Hoyer <har...@royal.net>)  looks like this:
-
-e:\loadlin\loadlin e:\zimage root=/dev/md0 md=0,0,4,0,/dev/hdb2,/dev/hdc3 ro
+
+``md device no.``
++++++++++++++++++
+
+The number of the md device
+
+================= =========
+``md device no.`` device
+================= =========
+              0                md0
+             1         md1
+             2         md2
+             3         md3
+             4         md4
+================= =========
+
+``raid level``
+++++++++++++++
+
+level of the RAID array
+
+=============== =============
+``raid level``  level
+=============== =============
+-1             linear mode
+0              striped mode
+=============== =============
+
+other modes are only supported with persistent super blocks
+
+``chunk size factor``
++++++++++++++++++++++
+
+(raid-0 and raid-1 only)
+
+Set  the chunk size as 4k << n.
+
+``fault level``
++++++++++++++++
+
+Totally ignored
+
+``dev0`` to ``devn``
+++++++++++++++++++++
+
+e.g. ``/dev/hda1``, ``/dev/hdc1``, ``/dev/sda1``, ``/dev/sdb1``
+
+A possible loadlin line (Harald Hoyer <har...@royal.net>)  looks like this::
+
+       e:\loadlin\loadlin e:\zimage root=/dev/md0 
md=0,0,4,0,/dev/hdb2,/dev/hdc3 ro
 
 
 Boot time autodetection of RAID arrays
@@ -45,10 +80,10 @@ Boot time autodetection of RAID arrays
 When md is compiled into the kernel (not as module), partitions of
 type 0xfd are scanned and automatically assembled into RAID arrays.
 This autodetection may be suppressed with the kernel parameter
-"raid=noautodetect".  As of kernel 2.6.9, only drives with a type 0
+``raid=noautodetect``.  As of kernel 2.6.9, only drives with a type 0
 superblock can be autodetected and run at boot time.
 
-The kernel parameter "raid=partitionable" (or "raid=part") means
+The kernel parameter ``raid=partitionable`` (or ``raid=part``) means
 that all auto-detected arrays are assembled as partitionable.
 
 Boot time assembly of degraded/dirty arrays
@@ -56,22 +91,23 @@ Boot time assembly of degraded/dirty arrays
 
 If a raid5 or raid6 array is both dirty and degraded, it could have
 undetectable data corruption.  This is because the fact that it is
-'dirty' means that the parity cannot be trusted, and the fact that it
+``dirty`` means that the parity cannot be trusted, and the fact that it
 is degraded means that some datablocks are missing and cannot reliably
 be reconstructed (due to no parity).
 
 For this reason, md will normally refuse to start such an array.  This
 requires the sysadmin to take action to explicitly start the array
-despite possible corruption.  This is normally done with
+despite possible corruption.  This is normally done with::
+
    mdadm --assemble --force ....
 
 This option is not really available if the array has the root
 filesystem on it.  In order to support this booting from such an
-array, md supports a module parameter "start_dirty_degraded" which,
+array, md supports a module parameter ``start_dirty_degraded`` which,
 when set to 1, bypassed the checks and will allows dirty degraded
 arrays to be started.
 
-So, to boot with a root filesystem of a dirty degraded raid[56], use
+So, to boot with a root filesystem of a dirty degraded raid 5 or 6, use::
 
    md-mod.start_dirty_degraded=1
 
@@ -80,30 +116,30 @@ Superblock formats
 ------------------
 
 The md driver can support a variety of different superblock formats.
-Currently, it supports superblock formats "0.90.0" and the "md-1" format
+Currently, it supports superblock formats ``0.90.0`` and the ``md-1`` format
 introduced in the 2.5 development series.
 
 The kernel will autodetect which format superblock is being used.
 
-Superblock format '0' is treated differently to others for legacy
+Superblock format ``0`` is treated differently to others for legacy
 reasons - it is the original superblock format.
 
 
 General Rules - apply for all superblock formats
 ------------------------------------------------
 
-An array is 'created' by writing appropriate superblocks to all
+An array is ``created`` by writing appropriate superblocks to all
 devices.
 
-It is 'assembled' by associating each of these devices with an
+It is ``assembled`` by associating each of these devices with an
 particular md virtual device.  Once it is completely assembled, it can
 be accessed.
 
 An array should be created by a user-space tool.  This will write
 superblocks to all devices.  It will usually mark the array as
-'unclean', or with some devices missing so that the kernel md driver
-can create appropriate redundancy (copying in raid1, parity
-calculation in raid4/5).
+``unclean``, or with some devices missing so that the kernel md driver
+can create appropriate redundancy (copying in raid 1, parity
+calculation in raid 4/5).
 
 When an array is assembled, it is first initialized with the
 SET_ARRAY_INFO ioctl.  This contains, in particular, a major and minor
@@ -126,13 +162,12 @@ Devices that have failed or are not yet active can be 
detached from an
 array using HOT_REMOVE_DISK.
 
 
-Specific Rules that apply to format-0 super block arrays, and
-       arrays with no superblock (non-persistent).
--------------------------------------------------------------
+Specific Rules that apply to format-0 super block arrays, and arrays with no 
superblock (non-persistent)
+--------------------------------------------------------------------------------------------------------
 
-An array can be 'created' by describing the array (level, chunksize
-etc) in a SET_ARRAY_INFO ioctl.  This must have major_version==0 and
-raid_disks != 0.
+An array can be ``created`` by describing the array (level, chunksize
+etc) in a SET_ARRAY_INFO ioctl.  This must have ``major_version==0`` and
+``raid_disks != 0``.
 
 Then uninitialized devices can be added with ADD_NEW_DISK.  The
 structure passed to ADD_NEW_DISK must specify the state of the device
@@ -142,24 +177,26 @@ Once started with RUN_ARRAY, uninitialized spares can be 
added with
 HOT_ADD_DISK.
 
 
-
 MD devices in sysfs
 -------------------
-md devices appear in sysfs (/sys) as regular block devices,
-e.g.
+
+md devices appear in sysfs (``/sys``) as regular block devices,
+e.g.::
+
    /sys/block/md0
 
-Each 'md' device will contain a subdirectory called 'md' which
+Each ``md`` device will contain a subdirectory called ``md`` which
 contains further md-specific information about the device.
 
 All md devices contain:
+
   level
-     a text file indicating the 'raid level'. e.g. raid0, raid1,
+     a text file indicating the ``raid level``. e.g. raid0, raid1,
      raid5, linear, multipath, faulty.
      If no raid level has been set yet (array is still being
      assembled), the value will reflect whatever has been written
      to it, which may be a name like the above, or may be a number
-     such as '0', '5', etc.
+     such as ``0``, ``5``, etc.
 
   raid_disks
      a text file with a simple number indicating the number of devices
@@ -172,10 +209,10 @@ All md devices contain:
      A change to this attribute will not be permitted if it would
      reduce the size of the array.  To reduce the number of drives
      in an e.g. raid5, the array size must first be reduced by
-     setting the 'array_size' attribute.
+     setting the ``array_size`` attribute.
 
   chunk_size
-     This is the size in bytes for 'chunks' and is only relevant to
+     This is the size in bytes for ``chunks`` and is only relevant to
      raid levels that involve striping (0,4,5,6,10). The address space
      of the array is conceptually divided into chunks and consecutive
      chunks are striped onto neighbouring devices.
@@ -183,7 +220,7 @@ All md devices contain:
      of 2.  This can only be set while assembling an array
 
   layout
-     The "layout" for the array for the particular level.  This is
+     The ``layout`` for the array for the particular level.  This is
      simply a number that is interpretted differently by different
      levels.  It can be written while assembling an array.
 
@@ -193,22 +230,24 @@ All md devices contain:
      devices.  Writing a number (in Kilobytes) which is less than
      the available size will set the size.  Any reconfiguration of the
      array (e.g. adding devices) will not cause the size to change.
-     Writing the word 'default' will cause the effective size of the
+     Writing the word ``default`` will cause the effective size of the
      array to be whatever size is actually available based on
-     'level', 'chunk_size' and 'component_size'.
+     ``level``, ``chunk_size`` and ``component_size``.
 
      This can be used to reduce the size of the array before reducing
      the number of devices in a raid4/5/6, or to support external
      metadata formats which mandate such clipping.
 
   reshape_position
-     This is either "none" or a sector number within the devices of
-     the array where "reshape" is up to.  If this is set, the three
+     This is either ``none`` or a sector number within the devices of
+     the array where ``reshape`` is up to.  If this is set, the three
      attributes mentioned above (raid_disks, chunk_size, layout) can
      potentially have 2 values, an old and a new value.  If these
-     values differ, reading the attribute returns
+     values differ, reading the attribute returns::
+
         new (old)
-     and writing will effect the 'new' value, leaving the 'old'
+
+     and writing will effect the ``new`` value, leaving the ``old``
      unchanged.
 
   component_size
@@ -223,9 +262,9 @@ All md devices contain:
   metadata_version
      This indicates the format that is being used to record metadata
      about the array.  It can be 0.90 (traditional format), 1.0, 1.1,
-     1.2 (newer format in varying locations) or "none" indicating that
+     1.2 (newer format in varying locations) or ``none`` indicating that
      the kernel isn't managing metadata at all.
-     Alternately it can be "external:" followed by a string which
+     Alternately it can be ``external:`` followed by a string which
      is set by user-space.  This indicates that metadata is managed
      by a user-space program.  Any device failure or other event that
      requires a metadata update will cause array activity to be
@@ -233,9 +272,9 @@ All md devices contain:
 
   resync_start
      The point at which resync should start.  If no resync is needed,
-     this will be a very large number (or 'none' since 2.6.30-rc1).  At
+     this will be a very large number (or ``none`` since 2.6.30-rc1).  At
      array creation it will default to 0, though starting the array as
-     'clean' will set it much larger.
+     ``clean`` will set it much larger.
 
    new_dev
      This file can be written but not read.  The value written should
@@ -246,10 +285,10 @@ All md devices contain:
 
    safe_mode_delay
      When an md array has seen no write requests for a certain period
-     of time, it will be marked as 'clean'.  When another write
-     request arrives, the array is marked as 'dirty' before the write
-     commences.  This is known as 'safe_mode'.
-     The 'certain period' is controlled by this file which stores the
+     of time, it will be marked as ``clean``.  When another write
+     request arrives, the array is marked as ``dirty`` before the write
+     commences.  This is known as ``safe_mode``.
+     The ``certain period`` is controlled by this file which stores the
      period as a number of seconds.  The default is 200msec (0.200).
      Writing a value of 0 disables safemode.
 
@@ -260,38 +299,50 @@ All md devices contain:
      cannot be explicitly set, and some transitions are not allowed.
 
      Select/poll works on this file.  All changes except between
-       active_idle and active (which can be frequent and are not
-       very interesting) are notified.  active->active_idle is
-       reported if the metadata is externally managed.
+     Active_idle and active (which can be frequent and are not
+     very interesting) are notified.  active->active_idle is
+     reported if the metadata is externally managed.
 
      clear
          No devices, no size, no level
+
          Writing is equivalent to STOP_ARRAY ioctl
+
      inactive
          May have some settings, but array is not active
-            all IO results in error
+         all IO results in error
+
          When written, doesn't tear down array, but just stops it
+
      suspended (not supported yet)
          All IO requests will block. The array can be reconfigured.
+
          Writing this, if accepted, will block until array is quiessent
+
      readonly
          no resync can happen.  no superblocks get written.
-         write requests fail
+
+         Write requests fail
+
      read-auto
-         like readonly, but behaves like 'clean' on a write request.
+         like readonly, but behaves like ``clean`` on a write request.
+
+     clean
+         no pending writes, but otherwise active.
 
-     clean - no pending writes, but otherwise active.
          When written to inactive array, starts without resync
+
          If a write request arrives then
-           if metadata is known, mark 'dirty' and switch to 'active'.
-           if not known, block and switch to write-pending
+         if metadata is known, mark ``dirty`` and switch to ``active``.
+         if not known, block and switch to write-pending
+
          If written to an active array that has pending writes, then fails.
      active
          fully active: IO and resync can be happening.
          When written to inactive array, starts with resync
 
      write-pending
-         clean, but writes are blocked waiting for 'active' to be written.
+         clean, but writes are blocked waiting for ``active`` to be written.
 
      active-idle
          like active, but no writes have been seen for a while 
(safe_mode_delay).
@@ -299,57 +350,71 @@ All md devices contain:
   bitmap/location
      This indicates where the write-intent bitmap for the array is
      stored.
-     It can be one of "none", "file" or "[+-]N".
-     "file" may later be extended to "file:/file/name"
-     "[+-]N" means that many sectors from the start of the metadata.
-       This is replicated on all devices.  For arrays with externally
-       managed metadata, the offset is from the beginning of the
-       device.
+
+     It can be one of ``none``, ``file`` or ``[+-]N``.
+     ``file`` may later be extended to ``file:/file/name``
+     ``[+-]N`` means that many sectors from the start of the metadata.
+
+     This is replicated on all devices.  For arrays with externally
+     managed metadata, the offset is from the beginning of the
+     device.
+
   bitmap/chunksize
      The size, in bytes, of the chunk which will be represented by a
      single bit.  For RAID456, it is a portion of an individual
      device. For RAID10, it is a portion of the array.  For RAID1, it
      is both (they come to the same thing).
+
   bitmap/time_base
      The time, in seconds, between looking for bits in the bitmap to
      be cleared. In the current implementation, a bit will be cleared
-     between 2 and 3 times "time_base" after all the covered blocks
+     between 2 and 3 times ``time_base`` after all the covered blocks
      are known to be in-sync.
+
   bitmap/backlog
      When write-mostly devices are active in a RAID1, write requests
      to those devices proceed in the background - the filesystem (or
      other user of the device) does not have to wait for them.
-     'backlog' sets a limit on the number of concurrent background
+     ``backlog`` sets a limit on the number of concurrent background
      writes.  If there are more than this, new writes will by
      synchronous.
+
   bitmap/metadata
-     This can be either 'internal' or 'external'.
-     'internal' is the default and means the metadata for the bitmap
-     is stored in the first 256 bytes of the allocated space and is
-     managed by the md module.
-     'external' means that bitmap metadata is managed externally to
-     the kernel (i.e. by some userspace program)
+     This can be either ``internal`` or ``external``.
+
+     ``internal``
+       is the default and means the metadata for the bitmap
+       is stored in the first 256 bytes of the allocated space and is
+       managed by the md module.
+
+     ``external``
+       means that bitmap metadata is managed externally to
+       the kernel (i.e. by some userspace program)
+
   bitmap/can_clear
-     This is either 'true' or 'false'.  If 'true', then bits in the
+     This is either ``true`` or ``false``.  If ``true``, then bits in the
      bitmap will be cleared when the corresponding blocks are thought
-     to be in-sync.  If 'false', bits will never be cleared.
-     This is automatically set to 'false' if a write happens on a
+     to be in-sync.  If ``false``, bits will never be cleared.
+     This is automatically set to ``false`` if a write happens on a
      degraded array, or if the array becomes degraded during a write.
      When metadata is managed externally, it should be set to true
      once the array becomes non-degraded, and this fact has been
      recorded in the metadata.
-     
-     
-     
 
-As component devices are added to an md array, they appear in the 'md'
-directory as new directories named
+
+
+
+As component devices are added to an md array, they appear in the ``md``
+directory as new directories named::
+
       dev-XXX
-where XXX is a name that the kernel knows for the device, e.g. hdb1.
+
+where ``XXX`` is a name that the kernel knows for the device, e.g. hdb1.
 Each directory contains:
 
       block
-        a symlink to the block device in /sys/block, e.g.
+        a symlink to the block device in /sys/block, e.g.::
+
             /sys/block/md0/md/dev-hdb1/block -> ../../../../block/hdb/hdb1
 
       super
@@ -358,51 +423,83 @@ Each directory contains:
 
       state
        A file recording the current state of the device in the array
-       which can be a comma separated list of
-             faulty   - device has been kicked from active use due to
-                        a detected fault, or it has unacknowledged bad
-                        blocks
-             in_sync  - device is a fully in-sync member of the array
-             writemostly - device will only be subject to read
-                        requests if there are no other options.
-                        This applies only to raid1 arrays.
-             blocked  - device has failed, and the failure hasn't been
-                        acknowledged yet by the metadata handler.
-                        Writes that would write to this device if
-                        it were not faulty are blocked.
-             spare    - device is working, but not a full member.
-                        This includes spares that are in the process
-                        of being recovered to
-             write_error - device has ever seen a write error.
-             want_replacement - device is (mostly) working but probably
-                        should be replaced, either due to errors or
-                        due to user request.
-             replacement - device is a replacement for another active
-                        device with same raid_disk.
+       which can be a comma separated list of:
+
+             faulty
+                       device has been kicked from active use due to
+                       a detected fault, or it has unacknowledged bad
+                       blocks
+
+             in_sync
+                       device is a fully in-sync member of the array
+
+             writemostly
+                       device will only be subject to read
+                       requests if there are no other options.
+
+                       This applies only to raid1 arrays.
+
+             blocked
+                       device has failed, and the failure hasn't been
+                       acknowledged yet by the metadata handler.
+
+                       Writes that would write to this device if
+                       it were not faulty are blocked.
+
+             spare
+                       device is working, but not a full member.
+
+                       This includes spares that are in the process
+                       of being recovered to
+
+             write_error
+                       device has ever seen a write error.
+
+             want_replacement
+                       device is (mostly) working but probably
+                       should be replaced, either due to errors or
+                       due to user request.
+
+             replacement
+                       device is a replacement for another active
+                       device with same raid_disk.
 
 
        This list may grow in future.
+
        This can be written to.
-       Writing "faulty"  simulates a failure on the device.
-       Writing "remove" removes the device from the array.
-       Writing "writemostly" sets the writemostly flag.
-       Writing "-writemostly" clears the writemostly flag.
-       Writing "blocked" sets the "blocked" flag.
-       Writing "-blocked" clears the "blocked" flags and allows writes
-               to complete and possibly simulates an error.
-       Writing "in_sync" sets the in_sync flag.
-       Writing "write_error" sets writeerrorseen flag.
-       Writing "-write_error" clears writeerrorseen flag.
-       Writing "want_replacement" is allowed at any time except to a
-               replacement device or a spare.  It sets the flag.
-       Writing "-want_replacement" is allowed at any time.  It clears
-               the flag.
-       Writing "replacement" or "-replacement" is only allowed before
-               starting the array.  It sets or clears the flag.
-
-
-       This file responds to select/poll. Any change to 'faulty'
-       or 'blocked' causes an event.
+
+       Writing ``faulty``  simulates a failure on the device.
+
+       Writing ``remove`` removes the device from the array.
+
+       Writing ``writemostly`` sets the writemostly flag.
+
+       Writing ``-writemostly`` clears the writemostly flag.
+
+       Writing ``blocked`` sets the ``blocked`` flag.
+
+       Writing ``-blocked`` clears the ``blocked`` flags and allows writes
+       to complete and possibly simulates an error.
+
+       Writing ``in_sync`` sets the in_sync flag.
+
+       Writing ``write_error`` sets writeerrorseen flag.
+
+       Writing ``-write_error`` clears writeerrorseen flag.
+
+       Writing ``want_replacement`` is allowed at any time except to a
+       replacement device or a spare.  It sets the flag.
+
+       Writing ``-want_replacement`` is allowed at any time.  It clears
+       the flag.
+
+       Writing ``replacement`` or ``-replacement`` is only allowed before
+       starting the array.  It sets or clears the flag.
+
+
+       This file responds to select/poll. Any change to ``faulty``
+       or ``blocked`` causes an event.
 
       errors
        An approximate count of read errors that have been detected on
@@ -417,9 +514,9 @@ Each directory contains:
 
       slot
         This gives the role that the device has in the array.  It will
-       either be 'none' if the device is not active in the array
+       either be ``none`` if the device is not active in the array
         (i.e. is a spare or has failed) or an integer less than the
-       'raid_disks' number for the array indicating which position
+       ``raid_disks`` number for the array indicating which position
        it currently fills.  This can only be set while assembling an
        array.  A device for which this is set is assumed to be working.
 
@@ -437,7 +534,7 @@ Each directory contains:
         written, it will be rejected.
 
       recovery_start
-        When the device is not 'in_sync', this records the number of
+        When the device is not ``in_sync``, this records the number of
        sectors from the start of the device which are known to be
        correct.  This is normally zero, but during a recovery
        operation it will steadily increase, and if the recovery is
@@ -447,21 +544,21 @@ Each directory contains:
 
        This can be set whenever the device is not an active member of
        the array, either before the array is activated, or before
-       the 'slot' is set.
+       the ``slot`` is set.
+
+       Setting this to ``none`` is equivalent to setting ``in_sync``.
+       Setting to any other value also clears the ``in_sync`` flag.
 
-       Setting this to 'none' is equivalent to setting 'in_sync'.
-       Setting to any other value also clears the 'in_sync' flag.
-       
       bad_blocks
        This gives the list of all known bad blocks in the form of
        start address and length (in sectors respectively). If output
        is too big to fit in a page, it will be truncated. Writing
-       "sector length" to this file adds new acknowledged (i.e.
+       ``sector length`` to this file adds new acknowledged (i.e.
        recorded to disk safely) bad blocks.
 
       unacknowledged_bad_blocks
        This gives the list of known-but-not-yet-saved-to-disk bad
-       blocks in the same form of 'bad_blocks'. If output is too big
+       blocks in the same form of ``bad_blocks``. If output is too big
        to fit in a page, it will be truncated. Writing to this file
        adds bad blocks without acknowledging them. This is largely
        for testing.
@@ -469,16 +566,18 @@ Each directory contains:
 
 
 An active md device will also contain an entry for each active device
-in the array.  These are named
+in the array.  These are named::
 
     rdNN
 
-where 'NN' is the position in the array, starting from 0.
+where ``NN`` is the position in the array, starting from 0.
 So for a 3 drive array there will be rd0, rd1, rd2.
-These are symbolic links to the appropriate 'dev-XXX' entry.
-Thus, for example,
+These are symbolic links to the appropriate ``dev-XXX`` entry.
+Thus, for example::
+
        cat /sys/block/md*/md/rd*/state
-will show 'in_sync' on every line.
+
+will show ``in_sync`` on every line.
 
 
 
@@ -488,50 +587,62 @@ also have
    sync_action
      a text file that can be used to monitor and control the rebuild
      process.  It contains one word which can be one of:
-       resync        - redundancy is being recalculated after unclean
-                       shutdown or creation
-       recover       - a hot spare is being built to replace a
-                       failed/missing device
-       idle          - nothing is happening
-       check         - A full check of redundancy was requested and is
-                       happening.  This reads all blocks and checks
-                       them. A repair may also happen for some raid
-                       levels.
-       repair        - A full check and repair is happening.  This is
-                       similar to 'resync', but was requested by the
-                       user, and the write-intent bitmap is NOT used to
-                      optimise the process.
+
+       resync
+               redundancy is being recalculated after unclean
+                shutdown or creation
+
+       recover
+               a hot spare is being built to replace a
+               failed/missing device
+
+       idle
+               nothing is happening
+       check
+               A full check of redundancy was requested and is
+                happening.  This reads all blocks and checks
+                them. A repair may also happen for some raid
+                levels.
+
+       repair
+               A full check and repair is happening.  This is
+               similar to ``resync``, but was requested by the
+                user, and the write-intent bitmap is NOT used to
+               optimise the process.
 
       This file is writable, and each of the strings that could be
       read are meaningful for writing.
 
-       'idle' will stop an active resync/recovery etc.  There is no
-           guarantee that another resync/recovery may not be automatically
-          started again, though some event will be needed to trigger
-           this.
-       'resync' or 'recovery' can be used to restart the
-           corresponding operation if it was stopped with 'idle'.
-       'check' and 'repair' will start the appropriate process
-           providing the current state is 'idle'.
+       ``idle`` will stop an active resync/recovery etc.  There is no
+       guarantee that another resync/recovery may not be automatically
+       started again, though some event will be needed to trigger
+       this.
+
+       ``resync`` or ``recovery`` can be used to restart the
+        corresponding operation if it was stopped with ``idle``.
+
+       ``check`` and ``repair`` will start the appropriate process
+       providing the current state is ``idle``.
 
       This file responds to select/poll.  Any important change in the value
       triggers a poll event.  Sometimes the value will briefly be
-      "recover" if a recovery seems to be needed, but cannot be
-      achieved. In that case, the transition to "recover" isn't
+      ``recover`` if a recovery seems to be needed, but cannot be
+      achieved. In that case, the transition to ``recover`` isn't
       notified, but the transition away is.
 
    degraded
       This contains a count of the number of devices by which the
-      arrays is degraded.  So an optimal array will show '0'.  A
-      single failed/missing drive will show '1', etc.
+      arrays is degraded.  So an optimal array will show ``0``.  A
+      single failed/missing drive will show ``1``, etc.
+
       This file responds to select/poll, any increase or decrease
       in the count of missing devices will trigger an event.
 
    mismatch_count
-      When performing 'check' and 'repair', and possibly when
-      performing 'resync', md will count the number of errors that are
-      found.  The count in 'mismatch_cnt' is the number of sectors
-      that were re-written, or (for 'check') would have been
+      When performing ``check`` and ``repair``, and possibly when
+      performing ``resync``, md will count the number of errors that are
+      found.  The count in ``mismatch_cnt`` is the number of sectors
+      that were re-written, or (for ``check``) would have been
       re-written.  As most raid levels work in units of pages rather
       than sectors, this may be larger than the number of actual errors
       by a factor of the number of sectors in a page.
@@ -542,27 +653,30 @@ also have
       would need to check the corresponding blocks. Either individual
       numbers or start-end pairs can be written.  Multiple numbers
       can be separated by a space.
-      Note that the numbers are 'bit' numbers, not 'block' numbers.
+
+      Note that the numbers are ``bit`` numbers, not ``block`` numbers.
       They should be scaled by the bitmap_chunksize.
 
-   sync_speed_min
-   sync_speed_max
-     This are similar to /proc/sys/dev/raid/speed_limit_{min,max}
+   sync_speed_min, sync_speed_max
+     This are similar to ``/proc/sys/dev/raid/speed_limit_{min,max}``
      however they only apply to the particular array.
-     If no value has been written to these, or if the word 'system'
+
+     If no value has been written to these, or if the word ``system``
      is written, then the system-wide value is used.  If a value,
      in kibibytes-per-second is written, then it is used.
+
      When the files are read, they show the currently active value
-     followed by "(local)" or "(system)" depending on whether it is
+     followed by ``(local)`` or ``(system)`` depending on whether it is
      a locally set or system-wide value.
 
    sync_completed
      This shows the number of sectors that have been completed of
      whatever the current sync_action is, followed by the number of
      sectors in total that could need to be processed.  The two
-     numbers are separated by a '/'  thus effectively showing one
+     numbers are separated by a ``/``  thus effectively showing one
      value, a fraction of the process that is complete.
-     A 'select' on this attribute will return when resync completes,
+
+     A ``select`` on this attribute will return when resync completes,
      when it reaches the current sync_max (below) and possibly at
      other times.
 
@@ -570,26 +684,24 @@ also have
      This shows the current actual speed, in K/sec, of the current
      sync_action.  It is averaged over the last 30 seconds.
 
-   suspend_lo
-   suspend_hi
+   suspend_lo, suspend_hi
      The two values, given as numbers of sectors, indicate a range
      within the array where IO will be blocked.  This is currently
      only supported for raid4/5/6.
 
-   sync_min
-   sync_max
+   sync_min, sync_max
      The two values, given as numbers of sectors, indicate a range
-     within the array where 'check'/'repair' will operate. Must be
-     a multiple of chunk_size. When it reaches "sync_max" it will
+     within the array where ``check``/``repair`` will operate. Must be
+     a multiple of chunk_size. When it reaches ``sync_max`` it will
      pause, rather than complete.
-     You can use 'select' or 'poll' on "sync_completed" to wait for
+     You can use ``select`` or ``poll`` on ``sync_completed`` to wait for
      that number to reach sync_max.  Then you can either increase
-     "sync_max", or can write 'idle' to "sync_action".
+     ``sync_max``, or can write ``idle`` to ``sync_action``.
 
-     The value of 'max' for "sync_max" effectively disables the limit.
+     The value of ``max`` for ``sync_max`` effectively disables the limit.
      When a resync is active, the value can only ever be increased,
      never decreased.
-     The value of '0' is the minimum for "sync_min".
+     The value of ``0`` is the minimum for ``sync_min``.
 
 
 
@@ -598,13 +710,15 @@ personality module that manages it.
 These are specific to the implementation of the module and could
 change substantially if the implementation changes.
 
-These currently include
+These currently include:
 
   stripe_cache_size  (currently raid5 only)
       number of entries in the stripe cache.  This is writable, but
       there are upper and lower limits (32768, 17).  Default is 256.
+
   strip_cache_active (currently raid5 only)
       number of active entries in the stripe cache
+
   preread_bypass_threshold (currently raid5 only)
       number of times a stripe requiring preread will be bypassed by
       a stripe that does not require preread.  For fairness defaults
diff --git a/Documentation/user/index.rst b/Documentation/user/index.rst
index 6762af7fc7f5..dd785849d149 100644
--- a/Documentation/user/index.rst
+++ b/Documentation/user/index.rst
@@ -17,6 +17,7 @@ Contents:
    kernel-parameters
    serial-console
    braile-console
+   md
    devices
    binfmt_misc
    bad_memory
diff --git a/Documentation/user/md.rst b/Documentation/user/md.rst
new file mode 120000
index 000000000000..19bd17b64e39
--- /dev/null
+++ b/Documentation/user/md.rst
@@ -0,0 +1 @@
+../md.txt
\ No newline at end of file
-- 
2.7.4


Reply via email to