Neil Armstrong <[email protected]> writes:
> Add pinctrl nodes and pin definitions for Amlogic Meson GXL.
>
> Signed-off-by: Neil Armstrong <[email protected]>
> ---
> arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 168
> +++++++++++++++++++++++++++++
> 1 file changed, 168 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> index 13b10ee..ce7f550 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl.dtsi
> @@ -42,7 +42,175 @@
> */
>
> #include "meson-gx.dtsi"
> +#include <dt-bindings/gpio/meson-gxl-gpio.h>
Oops, this has a dependency on the patch going through the pinctrl tree,
which causes probelems we like to avoid in the arm-soc tree.
For now, I've changed this to use the GXBB include since the values used
are the same, but we can fix this for good in v4.10-rc, after the GXL
pinctrl changes are merged.
Kevin
[1] [PATCH] pinctrl: meson: Add GXL pinctrl definitions
> / {
> compatible = "amlogic,meson-gxl";
> };
> +
> +&aobus {
> + pinctrl_aobus: pinctrl@14 {
> + compatible = "amlogic,meson-gxl-aobus-pinctrl";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + gpio_ao: bank@14 {
> + reg = <0x0 0x00014 0x0 0x8>,
> + <0x0 0x0002c 0x0 0x4>,
> + <0x0 0x00024 0x0 0x8>;
> + reg-names = "mux", "pull", "gpio";
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + uart_ao_a_pins: uart_ao_a {
> + mux {
> + groups = "uart_tx_ao_a", "uart_rx_ao_a";
> + function = "uart_ao";
> + };
> + };
> +
> + remote_input_ao_pins: remote_input_ao {
> + mux {
> + groups = "remote_input_ao";
> + function = "remote_input_ao";
> + };
> + };
> + };
> +};
> +
> +&periphs {
> + pinctrl_periphs: pinctrl@4b0 {
> + compatible = "amlogic,meson-gxl-periphs-pinctrl";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + gpio: bank@4b0 {
> + reg = <0x0 0x004b0 0x0 0x28>,
> + <0x0 0x004e8 0x0 0x14>,
> + <0x0 0x00120 0x0 0x14>,
> + <0x0 0x00430 0x0 0x40>;
> + reg-names = "mux", "pull", "pull-enable", "gpio";
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
> +
> + emmc_pins: emmc {
> + mux {
> + groups = "emmc_nand_d07",
> + "emmc_cmd",
> + "emmc_clk",
> + "emmc_ds";
> + function = "emmc";
> + };
> + };
> +
> + sdcard_pins: sdcard {
> + mux {
> + groups = "sdcard_d0",
> + "sdcard_d1",
> + "sdcard_d2",
> + "sdcard_d3",
> + "sdcard_cmd",
> + "sdcard_clk";
> + function = "sdcard";
> + };
> + };
> +
> + sdio_pins: sdio {
> + mux {
> + groups = "sdio_d0",
> + "sdio_d1",
> + "sdio_d2",
> + "sdio_d3",
> + "sdio_cmd",
> + "sdio_clk";
> + function = "sdio";
> + };
> + };
> +
> + sdio_irq_pins: sdio_irq {
> + mux {
> + groups = "sdio_irq";
> + function = "sdio";
> + };
> + };
> +
> + uart_a_pins: uart_a {
> + mux {
> + groups = "uart_tx_a",
> + "uart_rx_a";
> + function = "uart_a";
> + };
> + };
> +
> + uart_b_pins: uart_b {
> + mux {
> + groups = "uart_tx_b",
> + "uart_rx_b";
> + function = "uart_b";
> + };
> + };
> +
> + uart_c_pins: uart_c {
> + mux {
> + groups = "uart_tx_c",
> + "uart_rx_c";
> + function = "uart_c";
> + };
> + };
> +
> + i2c_a_pins: i2c_a {
> + mux {
> + groups = "i2c_sck_a",
> + "i2c_sda_a";
> + function = "i2c_a";
> + };
> + };
> +
> + i2c_b_pins: i2c_b {
> + mux {
> + groups = "i2c_sck_b",
> + "i2c_sda_b";
> + function = "i2c_b";
> + };
> + };
> +
> + i2c_c_pins: i2c_c {
> + mux {
> + groups = "i2c_sck_c",
> + "i2c_sda_c";
> + function = "i2c_c";
> + };
> + };
> +
> + eth_pins: eth_c {
> + mux {
> + groups = "eth_mdio",
> + "eth_mdc",
> + "eth_clk_rx_clk",
> + "eth_rx_dv",
> + "eth_rxd0",
> + "eth_rxd1",
> + "eth_rxd2",
> + "eth_rxd3",
> + "eth_rgmii_tx_clk",
> + "eth_tx_en",
> + "eth_txd0",
> + "eth_txd1",
> + "eth_txd2",
> + "eth_txd3";
> + function = "eth";
> + };
> + };
> +
> + pwm_e_pins: pwm_e {
> + mux {
> + groups = "pwm_e";
> + function = "pwm_e";
> + };
> + };
> + };
> +};
