Kevin is part of a family of boards called Gru. As best as possible, the
properties shared by the Gru family are placed in rk3399-gru.dtsi, while
Kevin-specific bits are in rk3399-gru-kevin.dts. This does not add full
support for the base Gru board.
Working and tested (to some extent):
* EC support -- including keyboard, battery, PWM, and probably more
* UART / console
* Thermal
* Touchscreen
* Touchpad
* Digitizer (regulator still WIP)
* PCIe / Wifi
* Bluetooth / Webcam
* SD card
* eMMC
* USB2 on TypeC
- This works much of the time, but USB3 devices may or may not detect
properly. Waiting on proper extcon support for USB3 over TypeC.
- Depends on XHCI/DWC3 fixes for ARM64 that still haven't landed
* Backlight
Not working:
* CPUFreq -- relies on special OVP support for our PWM regulator
circuits
* EC / extcon support -- and with it, USB3/TypeC/DP
* DRM -- won't even build on ARM64, so all display, eDP, etc. is not
enabled
Not tested:
* Audio
Signed-off-by: Brian Norris <briannor...@chromium.org>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts | 312 +++++++
arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi | 1006 +++++++++++++++++++++
3 files changed, 1319 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/Makefile
b/arch/arm64/boot/dts/rockchip/Makefile
index 3a862894ea44..b82f7b61ab6f 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-kevin.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
b/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
new file mode 100644
index 000000000000..66db785375a8
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
@@ -0,0 +1,312 @@
+/*
+ * Google Gru-Kevin Rev 6+ board device tree source
+ *
+ * Copyright 2016 Google, Inc
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "rk3399-gru.dtsi"
+#include <include/dt-bindings/input/linux-event-codes.h>
+
+/*
+ * Kevin-specific things
+ *
+ * Things in this section should use names from Kevin schematic since no
+ * equivalent exists in Gru schematic. If referring to signals that exist
+ * in Gru we use the Gru names, though. Confusing enough for you?
+ */
+/ {
+ model = "Google Kevin";
+ compatible = "google,kevin-rev15", "google,kevin-rev14",
+ "google,kevin-rev13", "google,kevin-rev12",
+ "google,kevin-rev11", "google,kevin-rev10",
+ "google,kevin-rev9", "google,kevin-rev8",
+ "google,kevin-rev7", "google,kevin-rev6",
+ "google,kevin", "google,gru", "rockchip,rk3399";
+
+ /* Power tree */
+
+ /* pp3300 children */
+
+ p3_3v_dig: p3-3v-dig {
+ compatible = "regulator-fixed";
+ regulator-name = "p3.3v_dig";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpu3_pen_pwr_en>;
+
+ enable-active-high;
+ gpio = <&gpio4 30 GPIO_ACTIVE_HIGH>;
+ vin-supply = <&pp3300>;
+ };
+
+ /* END REGULATORS */
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&cros_ec_pwm 1>;
+ brightness-levels = <0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
+ 17 18 19 20 21 22 23 24 25 26 27 28 29 30
+ 31 32 33 34 35 36 37 38 39 40 41 42 43 44
+ 45 46 47 48 49 50 51 52 53 54 55 56 57 58
+ 59 60 61 62 63 64 65 66 67 68 69 70 71 72
+ 73 74 75 76 77 78 79 80 81 82 83 84 85 86
+ 87 88 89 90 91 92 93 94 95 96 97 98 99
100>;
+ default-brightness-level = <51>;
+ enable-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+ power-supply = <&pp3300_disp>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en>;
+ pwm-delay-us = <10000>;
+ };
+
+ thermistor_ppvar_bigcpu: thermistor-ppvar-bigcpu {
+ compatible = "murata,ncp15wb473";
+ pullup-uv = <1800000>;
+ pullup-ohm = <25500>;
+ pulldown-ohm = <0>;
+ io-channels = <&saradc 2>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ thermistor_ppvar_litcpu: thermistor-ppvar-litcpu {
+ compatible = "murata,ncp15wb473";
+ pullup-uv = <1800000>;
+ pullup-ohm = <25500>;
+ pulldown-ohm = <0>;
+ io-channels = <&saradc 3>;
+ #thermal-sensor-cells = <0>;
+ };
+};
+
+&gpio_keys {
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l>, <&cpu1_pen_eject>;
+
+ pen-insert {
+ label = "Pen Insert";
+ /* Insert = low, eject = high */
+ gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+ linux,code = <SW_PEN_INSERTED>;
+ linux,input-type = <EV_SW>;
+ wakeup-source;
+ };
+};
+
+&thermal_zones {
+ bigcpu_reg_thermal: bigcpu-reg-thermal {
+ polling-delay-passive = <100>; /* milliseconds */
+ polling-delay = <1000>; /* milliseconds */
+ thermal-sensors = <&thermistor_ppvar_bigcpu 0>;
+ sustainable-power = <4000>;
+
+ ppvar_bigcpu_trips: trips {
+ ppvar_bigcpu_on: ppvar-bigcpu-on {
+ temperature = <40000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ ppvar_bigcpu_alert: ppvar-bigcpu-alert {
+ temperature = <50000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ ppvar_bigcpu_crit: ppvar-bigcpu-crit {
+ temperature = <90000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ trip = <&ppvar_bigcpu_alert>;
+ cooling-device =
+ <&cpu_l0 THERMAL_NO_LIMIT
THERMAL_NO_LIMIT>;
+ contribution = <4096>;
+ };
+ map1 {
+ trip = <&ppvar_bigcpu_alert>;
+ cooling-device =
+ <&cpu_b0 THERMAL_NO_LIMIT
THERMAL_NO_LIMIT>;
+ contribution = <1024>;
+ };
+ };
+ };
+
+ litcpu_reg_thermal: litcpu-reg-thermal {
+ polling-delay-passive = <100>; /* milliseconds */
+ polling-delay = <1000>; /* milliseconds */
+ thermal-sensors = <&thermistor_ppvar_litcpu 0>;
+ sustainable-power = <4000>;
+
+ ppvar_litcpu_trips: trips {
+ ppvar_litcpu_on: ppvar-litcpu-on {
+ temperature = <40000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ ppvar_litcpu_alert: ppvar-litcpu-alert {
+ temperature = <50000>; /* millicelsius */
+ hysteresis = <2000>; /* millicelsius */
+ type = "passive";
+ };
+
+ ppvar_litcpu_crit: ppvar-litcpu-crit {
+ temperature = <90000>; /* millicelsius */
+ hysteresis = <0>; /* millicelsius */
+ type = "critical";
+ };
+ };
+ };
+};
+
+ap_i2c_tpm: &i2c0 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ /* These are relatively safe rise/fall times. */
+ i2c-scl-falling-time-ns = <50>;
+ i2c-scl-rising-time-ns = <300>;
+
+ tpm: tpm@20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ powered-while-suspended;
+ };
+};
+
+ap_i2c_dig: &i2c2 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ /* These are relatively safe rise/fall times. */
+ i2c-scl-falling-time-ns = <50>;
+ i2c-scl-rising-time-ns = <300>;
+
+ digitizer: digitizer@9 {
+ compatible = "hid-over-i2c";
+ reg = <0x9>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpu1_dig_irq_l &cpu1_dig_pdct_l>;
+
+ interrupt-parent = <&gpio2>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+
+ hid-descr-addr = <0x1>;
+ };
+};
+
+/* Adjustments to things in the gru baseboard */
+
+&ap_i2c_tp {
+ trackpad@4a {
+ compatible = "atmel,atmel_mxt_tp";
+ reg = <0x4a>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&trackpad_int_l>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+ wakeup-source;
+ };
+};
+
+&ap_i2c_ts {
+ touchscreen@4b {
+ compatible = "atmel,atmel_mxt_ts";
+ reg = <0x4b>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_int_l>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <13 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&saradc {
+ status = "okay";
+ vref-supply = <&pp1800_ap_io>;
+};
+
+&mvl_wifi {
+ marvell,wakeup-pin = <14>; /* GPIO_14 on Marvell */
+};
+
+/* PINCTRL: always below everything else */
+
+&pinctrl {
+ digitizer {
+ /* Has external pullup */
+ cpu1_dig_irq_l: cpu1-dig-irq-l {
+ rockchip,pins = <2 4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ /* Has external pullup */
+ cpu1_dig_pdct_l: cpu1-dig-pdct-l {
+ rockchip,pins = <2 5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ discrete-regulators {
+ cpu3_pen_pwr_en: cpu3-pen-pwr-en {
+ rockchip,pins = <4 30 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pen {
+ cpu1_pen_eject: cpu1-pen-eject {
+ rockchip,pins = <0 13 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ wifi {
+ wlan_host_wake_l: wlan-host-wake-l {
+ rockchip,pins = <0 8 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+/* DON'T PUT ANYTHING BELOW HERE. PUT IT ABOVE PINCTRL */
+/* DON'T PUT ANYTHING BELOW HERE. PUT IT ABOVE PINCTRL */
+/* DON'T PUT ANYTHING BELOW HERE. PUT IT ABOVE PINCTRL */
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
new file mode 100644
index 000000000000..59b452504106
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -0,0 +1,1006 @@
+/*
+ * Google Gru (and derivatives) board device tree source
+ *
+ * Copyright 2016 Google, Inc
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/input/input.h>
+#include "rk3399.dtsi"
+
+/ {
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ /*
+ * Power Tree
+ *
+ * In general an attempt is made to include all rails called out by
+ * the schematic as long as those rails interact in some way with
+ * the AP. AKA:
+ * - Rails that only connect to the EC (or devices that the EC talks to)
+ * are not included.
+ * - Rails _are_ included if the rails go to the AP even if the AP
+ * doesn't currently care about them / they are always on. The idea
+ * here is that it makes it easier to map to the schematic or extend
+ * later.
+ *
+ * If two rails are substantially the same from the AP's point of
+ * view, though, we won't create a full fixed regulator. We'll just
+ * put the child rail as an alias of the parent rail. Sometimes rails
+ * look the same to the AP because one of these is true:
+ * - The EC controls the enable and the EC always enables a rail as
+ * long as the AP is running.
+ * - The rails are actually connected to each other by a jumper and
+ * the distinction is just there to add clarity/flexibility to the
+ * schematic.
+ */
+
+ /* parentless regulators */
+
+ ppvar_sys: ppvar-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvar_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ /* ppvar_sys children, sorted by name */
+
+ pp900_ap: pp900-ap {
+ compatible = "regulator-fixed";
+ regulator-name = "pp900_ap";
+
+ /* EC turns on w/ pp900_ap_en; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp1200_lpddr: pp1200-lpddr {
+ compatible = "regulator-fixed";
+ regulator-name = "pp1200_lpddr";
+
+ /* EC turns on w/ lpddr_pwr_en; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp1800: pp1800 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp1800";
+
+ /* Always on when ppvar_sys shows power good */
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp3000: pp3000 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3000";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pp3000_en>;
+
+ enable-active-high;
+ gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp3300: pp3300 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300";
+
+ /* Always on; plain and simple */
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ pp5000: pp5000 {
+ compatible = "regulator-fixed";
+ regulator-name = "pp5000";
+
+ /* EC turns on w/ pp5000_en; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ /* Schematics call this PPVAR even though it's fixed */
+ ppvar_logic: ppvar-logic {
+ compatible = "regulator-fixed";
+ regulator-name = "ppvar_logic";
+
+ /* EC turns on w/ ppvar_logic_en; always on for AP */
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <900000>;
+
+ vin-supply = <&ppvar_sys>;
+ };
+
+ /* pp900_ap aliases; these are always on for AP so just use alias */
+
+ /* EC turns on w/ pp900_ddrpll_en */
+ pp900_ddrpll: pp900-ap {
+ };
+
+ /* EC turns on w/ pp900_pcie_en */
+ pp900_pcie: pp900-ap {
+ };
+
+ /* EC turns on w/ pp900_pll_en */
+ pp900_pll: pp900-ap {
+ };
+
+ /* EC turns on w/ pp900_pmu_en */
+ pp900_pmu: pp900-ap {
+ };
+
+ /* EC turns on w/ pp900_usb_en */
+ pp900_usb: pp900-ap {
+ };
+
+ /* pp1800 aliases; these are always on for AP so just use alias */
+
+ /* EC turns on w/ pp1800_s0_en_l */
+ pp1800_ap_io: pp1800_emmc: pp1800_nfc: pp1800_s0: pp1800 {
+ };
+
+ /* EC turns on w/ pp1800_avdd_en_l */
+ pp1800_avdd: pp1800 {
+ };
+
+ /* EC turns on w/ pp1800_lid_en_l */
+ pp1800_lid: pp1800_mic: pp1800 {
+ };
+
+ /* EC turns on w/ lpddr_pwr_en */
+ pp1800_lpddr: pp1800 {
+ };
+
+ /* EC turns on w/ pp1800_pmu_en_l */
+ pp1800_pmu: pp1800 {
+ };
+
+ /* EC turns on w/ pp1800_usb_en_l */
+ pp1800_usb: pp1800 {
+ };
+
+ /* pp1800 children */
+
+ pp1500_ap_io: pp1500-ap-io {
+ compatible = "regulator-fixed";
+ regulator-name = "pp1500_ap_io";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pp1500_en>;
+
+ enable-active-high;
+ gpio = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+
+ vin-supply = <&pp1800>;
+ };
+
+ pp1800_audio: pp1800-audio {
+ compatible = "regulator-fixed";
+ regulator-name = "pp1800_audio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pp1800_audio_en>;
+
+ regulator-always-on;
+ regulator-boot-on;
+
+ enable-active-high;
+ gpio = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+
+ vin-supply = <&pp1800>;
+ };
+
+ pp1800_pcie: pp1800-pcie {
+ compatible = "regulator-fixed";
+ regulator-name = "pp1800_pcie";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_module_pd_l>;
+
+ /*
+ * Need to wait 1ms + ramp-up time before we can power on WiFi.
+ * This has been approximated as 8ms total.
+ */
+ regulator-enable-ramp-delay = <8000>;
+
+ enable-active-high;
+ gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+
+ vin-supply = <&pp1800>;
+ };
+
+ /*
+ * See http://crosbug.com/p/56069/
+ *
+ * This is a bit of a hack. The WiFi module should be reset at least
+ * 1ms after its regulators have ramped up (max rampup time is ~7ms).
+ * With some stretching of the imagination, we can call the 1.8V
+ * regulator a supply.
+ */
+ wlan_pd_n: wlan-pd-n {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan_pd_n";
+
+ /* Note the wlan_module_reset_l pinctrl */
+ enable-active-high;
+ gpio = <&gpio1 11 GPIO_ACTIVE_HIGH>;
+
+ vin-supply = <&pp1800_pcie>;
+ };
+
+ /* pp3000 aliases; these are always on for AP so just use alias */
+
+ /* Always on; plain and simple */
+ pp3000_ap: pp3000_emmc: pp3000 {
+ };
+
+ /* pp3000 children */
+
+ pp3000_sd_slot: pp3000-sd-slot {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3000_sd_slot";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd_slot_pwr_en>;
+
+ enable-active-high;
+ gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+
+ vin-supply = <&pp3000>;
+ };
+
+ /*
+ * Technically, this is a small abuse of 'regulator-gpio'; this
+ * regulator is a mux between pp1800 and pp3300. pp1800 and pp3300 are
+ * always on though, so it is sufficient to simply control the mux
+ * here.
+ */
+ ppvar_sd_card_io: ppvar-sd-card-io {
+ compatible = "regulator-gpio";
+ regulator-name = "ppvar_sd_card_io";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>;
+
+ enable-active-high;
+ enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+ gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3000000 0x0>;
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ /* pp3300 aliases; these are always on for AP so just use alias */
+
+ /* EC turns on w/ pp3300_trackpad_en_l */
+ pp3300_trackpad: pp3300-trackpad {
+ };
+
+ /* EC turns on w/ pp3300_usb_en_l */
+ pp3300_usb: pp3300 {
+ };
+
+ /* pp3300 children */
+
+ pp3300_disp: pp3300-disp {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_disp";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pp3300_disp_en>;
+
+ enable-active-high;
+
+ gpio = <&gpio4 27 GPIO_ACTIVE_HIGH>;
+
+ startup-delay-us = <2000>;
+ vin-supply = <&pp3300>;
+ };
+
+ pp3300_wifi_bt: pp3300-wifi-bt {
+ compatible = "regulator-fixed";
+ regulator-name = "pp3300_wifi_bt";
+ /* NOTE: wlan_module_pd_l pinctrl in pp1800_pcie */
+
+ enable-active-high;
+
+ /* NOTE: this GPIO also used in pp1800_pcie */
+ gpio = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+
+ vin-supply = <&pp3300>;
+ };
+
+ /* pp5000 aliases; these are always on for AP so just use alias */
+
+ /* EC turns on w/ usb_a_en */
+ pp5000_usb_a_vbus: pp5000 {
+ };
+
+ /* END REGULATORS */
+
+ io-domains {
+ compatible = "rockchip,rk3399-io-voltage-domain";
+ rockchip,grf = <&grf>;
+
+ bt656-supply = <&pp1800_ap_io>; /* APIO2_VDD; 2a 2b */
+ audio-supply = <&pp1800_audio>; /* APIO5_VDD; 3d 4a */
+ sdmmc-supply = <&ppvar_sd_card_io>; /* SDMMC0_VDD; 4b */
+ gpio1830-supply = <&pp3000_ap>; /* APIO4_VDD; 4c 4d */
+ };
+
+ max98357a: max98357a {
+ #sound-dai-cells = <0>;
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmode_en>;
+
+ compatible = "maxim,max98357a";
+ sdmode-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ sdmode-delay = <2>;
+ };
+
+ pmu-io-domains {
+ compatible = "rockchip,rk3399-pmu-io-voltage-domain";
+ rockchip,grf = <&pmugrf>;
+
+ pmu1830-supply = <&pp1800_pmu>; /* PMUIO2_VDD */
+ };
+
+ sound {
+ compatible = "rockchip,rk3399-gru-sound";
+ rockchip,cpu = <&i2s0 &i2s2>;
+ rockchip,codec = <&max98357a &headsetcodec &codec>;
+ };
+
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_host_wake_l>;
+
+ wake-on-bt {
+ label = "Wake-on-Bluetooth";
+ gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WAKEUP>;
+ wakeup-source;
+ };
+ };
+};
+
+&cru {
+ assigned-clocks =
+ <&cru PLL_GPLL>, <&cru PLL_CPLL>,
+ <&cru PLL_NPLL>,
+ <&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>,
+ <&cru PCLK_PERIHP>,
+ <&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
+ <&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
+ <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>;
+ assigned-clock-rates =
+ <594000000>, <800000000>,
+ <1000000000>,
+ <150000000>, <75000000>,
+ <37500000>,
+ <100000000>, <100000000>,
+ <50000000>, <800000000>,
+ <100000000>, <50000000>;
+};
+
+&emmc_phy {
+ status = "okay";
+};
+
+ap_i2c_mic: &i2c1 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ /* These are relatively safe rise/fall times */
+ i2c-scl-falling-time-ns = <50>;
+ i2c-scl-rising-time-ns = <300>;
+
+ headsetcodec: rt5514@57 {
+ compatible = "realtek,rt5514";
+ reg = <0x57>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mic_int>;
+
+ interrupt-parent = <&gpio1>;
+ interrupts = <13 IRQ_TYPE_LEVEL_HIGH>;
+
+ realtek,dmic-init-delay = <20>;
+ wakeup-source;
+ };
+};
+
+ap_i2c_ts: &i2c3 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ /* These are relatively safe rise/fall times */
+ i2c-scl-falling-time-ns = <50>;
+ i2c-scl-rising-time-ns = <300>;
+};
+
+ap_i2c_tp: &i2c5 {
+ status = "okay";
+
+ /*
+ * Note strange pullup enable. Apparently this avoids leakage but
+ * still allows us to get nice 4.7K pullups for high speed i2c
+ * transfers. Basically we want the pullup on whenever the ap is
+ * alive, so the "en" pin just gets set to output high.
+ */
+ pinctrl-0 = <&i2c5_xfer &ap_i2c_tp_pu_en>;
+
+ clock-frequency = <400000>;
+
+ /* These are relatively safe rise/fall times */
+ i2c-scl-falling-time-ns = <50>;
+ i2c-scl-rising-time-ns = <300>;
+};
+
+ap_i2c_audio: &i2c8 {
+ status = "okay";
+
+ clock-frequency = <400000>;
+
+ /* These are relatively safe rise/fall times */
+ i2c-scl-falling-time-ns = <50>;
+ i2c-scl-rising-time-ns = <300>;
+
+ codec: da7219@1a {
+ compatible = "dlg,da7219";
+ reg = <0x1a>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&headset_int_l>;
+
+ interrupt-parent = <&gpio1>;
+ interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+
+ VDD-supply = <&pp1800>;
+ VDDMIC-supply = <&pp3300>;
+ VDDIO-supply = <&pp1800>;
+
+ clocks = <&cru SCLK_I2S_8CH_OUT>;
+ clock-names = "mclk";
+
+ dlg,ldo-lvl = <1200>;
+ dlg,micbias-lvl = <2600>;
+ dlg,mic-amp-in-sel = "diff";
+
+ da7219_aad {
+ dlg,btn-cfg = <50>;
+ dlg,mic-det-thr = <500>;
+ dlg,jack-ins-deb = <20>;
+ dlg,jack-det-rate = "32ms_64ms";
+ dlg,jack-rem-deb = <1>;
+
+ dlg,a-d-btn-thr = <0xa>;
+ dlg,d-b-btn-thr = <0x16>;
+ dlg,b-c-btn-thr = <0x21>;
+ dlg,c-mic-btn-thr = <0x3E>;
+
+ dlg,btn-avg = <4>;
+ dlg,adc-1bit-rpt = <1>;
+ };
+ };
+};
+
+&i2s0 {
+ status = "okay";
+};
+
+&i2s2 {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_clkreqn_cpm>, <&wifi_perst_l>;
+ ep-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
+
+ max-link-speed = <1>;
+
+ vpcie3v3-supply = <&pp3300_wifi_bt>;
+ vpcie1v8-supply = <&wlan_pd_n>; /* HACK: see &wlan_pd_n */
+ vpcie0v9-supply = <&pp900_pcie>;
+
+ pci_rootport: pcie@0,0 {
+ reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ mvl_wifi: wifi@0,0 {
+ compatible = "pci1b4b,2b42";
+ reg = <0x83010000 0x0 0x00000000 0x0 0x00100000
+ 0x83010000 0x0 0x00100000 0x0 0x00100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_host_wake_l>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+ wakeup-source;
+ };
+ };
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pwm0 {
+ status = "okay";
+};
+
+&pwm1 {
+ status = "okay";
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&pwm3 {
+ status = "okay";
+};
+
+&sdhci {
+ /*
+ * Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
+ * same (or nearly the same) performance for all eMMC that are intended
+ * to be used.
+ */
+ assigned-clock-rates = <150000000>;
+
+ bus-width = <8>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ non-removable;
+ status = "okay";
+};
+
+&sdmmc {
+ status = "okay";
+
+ /*
+ * Note: configure "sdmmc_cd" as card detect even though it's actually
+ * hooked to ground. Because we specified "cd-gpios" below dw_mmc
+ * should be ignoring card detect anyway. Specifying the pin as
+ * sdmmc_cd means that even if you've got GRF_SOC_CON7[12] (force_jtag)
+ * turned on that the system will still make sure the port is
+ * configured as SDMMC and not JTAG.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_cd_gpio
+ &sdmmc_bus4>;
+
+ bus-width = <4>;
+ cd-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+ disable-wp;
+
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+
+ vmmc-supply = <&pp3000_sd_slot>;
+ vqmmc-supply = <&ppvar_sd_card_io>;
+};
+
+&spi1 {
+ status = "okay";
+
+ spiflash@0 {
+ compatible = "jedec,spi-nor";
+
+ /* May run faster once verified. */
+ spi-max-frequency = <10000000>;
+ reg = <0>;
+ };
+};
+
+&spi2 {
+ status = "okay";
+
+ wacky_spi_audio: spi2@0 {
+ compatible = "realtek,rt5514";
+ reg = <0>;
+
+ /* May run faster once verified. */
+ spi-max-frequency = <10000000>;
+ };
+};
+
+&spi5 {
+ status = "okay";
+
+ cros_ec: ec@0 {
+ compatible = "google,cros-ec-spi";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ec_ap_int_l>;
+
+ google,cros-ec-spi-pre-delay = <30>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <3000000>;
+
+ i2c_tunnel: i2c-tunnel {
+ compatible = "google,cros-ec-i2c-tunnel";
+ google,remote-bus = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cros_ec_pwm: ec-pwm {
+ compatible = "google,cros-ec-pwm";
+ #pwm-cells = <1>;
+ };
+ };
+};
+
+&tsadc {
+ status = "okay";
+
+ rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
+ rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
+};
+
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy0_host {
+ status = "okay";
+};
+
+&u2phy1_host {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usbdrd3_0 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+&usbdrd3_1 {
+ status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+#include "common/cros-ec-keyboard.dtsi"
+#include "common/cros-ec-sbs.dtsi"
+
+/* PINCTRL: always below everything else */
+
+&pinctrl {
+ /*
+ * pinctrl settings for pins that have no real owners.
+ *
+ * At the moment settings are identical for S0 and S3, but if we later
+ * need to configure things differently for S3 we'll adjust here.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <
+ &ap_pwroff /* AP will auto-assert this when in S3 */
+ &clk_32k /* This pin is always 32k on gru boards */
+
+ /*
+ * We want this driven low ASAP; firmware should help us, but
+ * we can help ourselves too.
+ */
+ &wlan_module_reset_l
+ >;
+
+ pcfg_output_low: pcfg-output-low {
+ output-low;
+ };
+
+ pcfg_output_high: pcfg-output-high {
+ output-high;
+ };
+
+ pcfg_pull_none_8ma: pcfg-pull-none-8ma {
+ bias-disable;
+ drive-strength = <8>;
+ };
+
+ cros-ec {
+ ec_ap_int_l: ec-ap-int-l {
+ rockchip,pins = <RK_GPIO0 1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ discrete-regulators {
+ pp1500_en: pp1500-en {
+ rockchip,pins = <RK_GPIO0 10 RK_FUNC_GPIO
+ &pcfg_pull_none>;
+ };
+
+ pp1800_audio_en: pp1800-audio-en {
+ rockchip,pins = <RK_GPIO0 2 RK_FUNC_GPIO
+ &pcfg_pull_down>;
+ };
+
+ pp3300_disp_en: pp3300-disp-en {
+ rockchip,pins = <RK_GPIO4 27 RK_FUNC_GPIO
+ &pcfg_pull_none>;
+ };
+
+ pp3000_en: pp3000-en {
+ rockchip,pins = <RK_GPIO0 12 RK_FUNC_GPIO
+ &pcfg_pull_none>;
+ };
+
+ sd_io_pwr_en: sd-io-pwr-en {
+ rockchip,pins = <RK_GPIO2 2 RK_FUNC_GPIO
+ &pcfg_pull_none>;
+ };
+
+ sd_pwr_1800_sel: sd-pwr-1800-sel {
+ rockchip,pins = <RK_GPIO2 28 RK_FUNC_GPIO
+ &pcfg_pull_none>;
+ };
+
+ sd_slot_pwr_en: sd-slot-pwr-en {
+ rockchip,pins = <RK_GPIO4 29 RK_FUNC_GPIO
+ &pcfg_pull_none>;
+ };
+
+ wlan_module_pd_l: wlan-module-pd-l {
+ rockchip,pins = <RK_GPIO0 4 RK_FUNC_GPIO
+ &pcfg_pull_down>;
+ };
+ };
+
+ codec {
+ /* Has external pullup */
+ headset_int_l: headset-int-l {
+ rockchip,pins = <1 23 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ mic_int: mic-int {
+ rockchip,pins = <1 13 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ max98357a {
+ sdmode_en: sdmode-en {
+ rockchip,pins = <1 2 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ sdmmc {
+ /*
+ * We run sdmmc at max speed; bump up drive strength.
+ * We also have external pulls, so disable the internal ones.
+ */
+ sdmmc_bus4: sdmmc-bus4 {
+ rockchip,pins =
+ <4 8 RK_FUNC_1 &pcfg_pull_none_8ma>,
+ <4 9 RK_FUNC_1 &pcfg_pull_none_8ma>,
+ <4 10 RK_FUNC_1 &pcfg_pull_none_8ma>,
+ <4 11 RK_FUNC_1 &pcfg_pull_none_8ma>;
+ };
+
+ sdmmc_clk: sdmmc-clk {
+ rockchip,pins =
+ <4 12 RK_FUNC_1 &pcfg_pull_none_8ma>;
+ };
+
+ sdmmc_cmd: sdmmc-cmd {
+ rockchip,pins =
+ <4 13 RK_FUNC_1 &pcfg_pull_none_8ma>;
+ };
+
+ /*
+ * In our case the official card detect is hooked to ground
+ * to avoid getting access to JTAG just by sticking something
+ * in the SD card slot (see the force_jtag bit in the TRM).
+ *
+ * We still configure it as card detect because it doesn't
+ * hurt and dw_mmc will ignore it. We make sure to disable
+ * the pull though so we don't burn needless power.
+ */
+ sdmmc_cd: sdmcc-cd {
+ rockchip,pins =
+ <0 7 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
+ /* This is where we actually hook up CD; has external pull */
+ sdmmc_cd_gpio: sdmmc-cd-gpio {
+ rockchip,pins = <4 24 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ trackpad {
+ ap_i2c_tp_pu_en: ap-i2c-tp-pu-en {
+ rockchip,pins = <3 12 RK_FUNC_GPIO &pcfg_output_high>;
+ };
+
+ trackpad_int_l: trackpad-int-l {
+ rockchip,pins = <1 4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ touchscreen {
+ touch_int_l: touch-int-l {
+ rockchip,pins = <3 13 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ touch_reset_l: touch-reset-l {
+ rockchip,pins = <4 26 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wifi {
+ wifi_perst_l: wifi-perst-l {
+ rockchip,pins = <2 27 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wlan_module_reset_l: wlan-module-reset-l {
+ /*
+ * We want this driven low ASAP (As {Soon,Strongly} As
+ * Possible), to avoid leakage through the powered-down
+ * WiFi.
+ */
+ rockchip,pins = <1 11 RK_FUNC_GPIO &pcfg_output_low>;
+ };
+
+ bt_host_wake_l: bt-host-wake-l {
+ /* Kevin has an external pull up, but Gru does not */
+ rockchip,pins = <0 3 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ backlight-enable {
+ bl_en: bl-en {
+ rockchip,pins = <1 17 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ write-protect {
+ ap_fw_wp: ap-fw-wp {
+ rockchip,pins = <1 18 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ pcie {
+ pcie_clkreqn_cpm: pci-clkreqn-cpm {
+ /*
+ * Since our pcie doesn't support ClockPM(CPM), we want
+ * to hack this as gpio, so the EP could be able to
+ * de-assert it along and make ClockPM(CPM) work.
+ */
+ rockchip,pins = <2 26 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+/* DON'T PUT ANYTHING BELOW HERE. PUT IT ABOVE PINCTRL */
+/* DON'T PUT ANYTHING BELOW HERE. PUT IT ABOVE PINCTRL */
+/* DON'T PUT ANYTHING BELOW HERE. PUT IT ABOVE PINCTRL */
+
--
2.8.0.rc3.226.g39d4020
