On Friday 22 September 2017 10:14 PM, Douglas Anderson wrote: > Calculate the calibration code as per the docs. The docs talk about > reading and averaging the pullup and pulldown calibration codes. They > also talk about adding in some adjustment codes. Let's do what the > docs say. > > In practice this doesn't seem to matter a whole lot. On a device I > tested the pullup and pulldown codes were nearly the same (0x23 and > 0x24) and the adjustment codes were 0. > > Reviewed-by: Chris Zhong <z...@rock-chips.com> > Signed-off-by: Douglas Anderson <diand...@chromium.org>
merged the 3rd and 4th patch to next. Thanks! -Kishon > --- > > Changes in v3: None > Changes in v2: > - Removed extra blank line. > > drivers/phy/rockchip/phy-rockchip-typec.c | 27 ++++++++++++++++++--------- > 1 file changed, 18 insertions(+), 9 deletions(-) > > diff --git a/drivers/phy/rockchip/phy-rockchip-typec.c > b/drivers/phy/rockchip/phy-rockchip-typec.c > index 95f8f23676b4..a96635447d48 100644 > --- a/drivers/phy/rockchip/phy-rockchip-typec.c > +++ b/drivers/phy/rockchip/phy-rockchip-typec.c > @@ -560,24 +560,33 @@ static void tcphy_dp_aux_calibration(struct > rockchip_typec_phy *tcphy) > u16 val; > u16 tx_ana_ctrl_reg_1; > u16 tx_ana_ctrl_reg_2; > - s32 pu_calib_code; > - > - /* disable txda_cal_latch_en for rewrite the calibration values */ > - tx_ana_ctrl_reg_1 = readl(tcphy->base + TX_ANA_CTRL_REG_1); > - tx_ana_ctrl_reg_1 &= ~TXDA_CAL_LATCH_EN; > - writel(tx_ana_ctrl_reg_1, tcphy->base + TX_ANA_CTRL_REG_1); > + s32 pu_calib_code, pd_calib_code; > + s32 pu_adj, pd_adj; > + u16 calib; > > /* > - * read a resistor calibration code from CMN_TXPUCAL_CTRL[5:0] and > - * write it to TX_DIG_CTRL_REG_2[5:0]. > + * Calculate calibration code as per docs: use an average of the > + * pull down and pull up. Then add in adjustments. > */ > val = readl(tcphy->base + CMN_TXPUCAL_CTRL); > pu_calib_code = CMN_CALIB_CODE_POS(val); > + val = readl(tcphy->base + CMN_TXPDCAL_CTRL); > + pd_calib_code = CMN_CALIB_CODE_POS(val); > + val = readl(tcphy->base + CMN_TXPU_ADJ_CTRL); > + pu_adj = CMN_CALIB_CODE(val); > + val = readl(tcphy->base + CMN_TXPD_ADJ_CTRL); > + pd_adj = CMN_CALIB_CODE(val); > + calib = (pu_calib_code + pd_calib_code) / 2 + pu_adj + pd_adj; > + > + /* disable txda_cal_latch_en for rewrite the calibration values */ > + tx_ana_ctrl_reg_1 = readl(tcphy->base + TX_ANA_CTRL_REG_1); > + tx_ana_ctrl_reg_1 &= ~TXDA_CAL_LATCH_EN; > + writel(tx_ana_ctrl_reg_1, tcphy->base + TX_ANA_CTRL_REG_1); > > /* write the calibration, then delay 10 ms as sample in docs */ > val = readl(tcphy->base + TX_DIG_CTRL_REG_2); > val &= ~(TX_RESCAL_CODE_MASK << TX_RESCAL_CODE_OFFSET); > - val |= pu_calib_code << TX_RESCAL_CODE_OFFSET; > + val |= calib << TX_RESCAL_CODE_OFFSET; > writel(val, tcphy->base + TX_DIG_CTRL_REG_2); > usleep_range(10000, 10050); > >
