Hi Chanwoo,
On Mon, Oct 30, 2017 at 5:32 AM, Chanwoo Choi <cw00.c...@samsung.com> wrote:
> Hi,
>
> On 2017년 10월 27일 17:35, Kishon Vijay Abraham I wrote:
>> +Chanwoo, for reviewing extcon
>>
>> Hi.
>>
>> On Tuesday 24 October 2017 10:07 AM, Raveendra Padasalagi wrote:
>>> Add driver for Broadcom's USB phy controller's used in Cygnus
>>> familyof SoC. Cygnus has three USB phy controller's, port 0,
>>> port 1 provides USB host functionality and port 2 can be configured
>>> for host/device role.
>>>
>>> Configuration of host/device role for port 2 is achieved based on
>>> the extcon events, the driver registers to extcon framework to get
>>> appropriate connect events for Host/Device cables connect/disconnect
>>> states based on VBUS and ID interrupts.
>>>
>>> Signed-off-by: Raveendra Padasalagi <raveendra.padasal...@broadcom.com>
>>> ---
>>> drivers/phy/broadcom/Kconfig | 14 +
>>> drivers/phy/broadcom/Makefile | 1 +
>>> drivers/phy/broadcom/phy-bcm-cygnus-usb.c | 672
>>> ++++++++++++++++++++++++++++++
>>> 3 files changed, 687 insertions(+)
>>> create mode 100644 drivers/phy/broadcom/phy-bcm-cygnus-usb.c
>>>
>>> diff --git a/drivers/phy/broadcom/Kconfig b/drivers/phy/broadcom/Kconfig
>>> index 64fc59c..3179daf 100644
>>> --- a/drivers/phy/broadcom/Kconfig
>>> +++ b/drivers/phy/broadcom/Kconfig
>>> @@ -1,6 +1,20 @@
>>> #
>>> # Phy drivers for Broadcom platforms
>>> #
>>> +config PHY_BCM_CYGNUS_USB
>>> + tristate "Broadcom Cygnus USB PHY support"
>>> + depends on OF
>>> + depends on ARCH_BCM_CYGNUS || COMPILE_TEST
>>> + select GENERIC_PHY
>>> + select EXTCON_USB_GPIO
>
> IMO, it is not good to add the dependency to the specific device driver.
> Instead, you better to depend on the EXTCON framework (select EXTCON)
> such as 'select GENERIC_PHY'.
GENERIC_PHY dependency is anyway needed and it's added as dependency.
Let me add "depends on EXTCON" instead of "select EXTCON"
>>
>> Didn't this throw up a warning for selecting config without caring for the
>> dependency?
>>
>>> + default ARCH_BCM_CYGNUS
>>> + help
>>> + Enable this to support three USB PHY's present in Broadcom's
>>> + Cygnus chip.
>>> +
>>> + The phys are capable of supporting host mode on all ports and
>>> + device mode for port 2.
>>> +
>>> config PHY_CYGNUS_PCIE
>>> tristate "Broadcom Cygnus PCIe PHY driver"
>>> depends on OF && (ARCH_BCM_CYGNUS || COMPILE_TEST)
>>> diff --git a/drivers/phy/broadcom/Makefile b/drivers/phy/broadcom/Makefile
>>> index 4eb82ec..3dec23c 100644
>>> --- a/drivers/phy/broadcom/Makefile
>>> +++ b/drivers/phy/broadcom/Makefile
>>> @@ -1,4 +1,5 @@
>>> obj-$(CONFIG_PHY_CYGNUS_PCIE) += phy-bcm-cygnus-pcie.o
>>> +obj-$(CONFIG_PHY_BCM_CYGNUS_USB) += phy-bcm-cygnus-usb.o
>>> obj-$(CONFIG_BCM_KONA_USB2_PHY) += phy-bcm-kona-usb2.o
>>> obj-$(CONFIG_PHY_BCM_NS_USB2) += phy-bcm-ns-usb2.o
>>> obj-$(CONFIG_PHY_BCM_NS_USB3) += phy-bcm-ns-usb3.o
>>> diff --git a/drivers/phy/broadcom/phy-bcm-cygnus-usb.c
>>> b/drivers/phy/broadcom/phy-bcm-cygnus-usb.c
>>> new file mode 100644
>>> index 0000000..ef2a94c
>>> --- /dev/null
>>> +++ b/drivers/phy/broadcom/phy-bcm-cygnus-usb.c
>>> @@ -0,0 +1,672 @@
>>> +/*
>>> + * Copyright 2017 Broadcom
>>> + *
>>> + * This program is free software; you can redistribute it and/or modify
>>> + * it under the terms of the GNU General Public License, version 2, as
>>> + * published by the Free Software Foundation (the "GPL").
>>> + *
>>> + * This program is distributed in the hope that it will be useful, but
>>> + * WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
>>> + * General Public License version 2 (GPLv2) for more details.
>>> + *
>>> + * You should have received a copy of the GNU General Public License
>>> + * version 2 (GPLv2) along with this source code.
>>> + */
>>> +
>>> +#include <linux/module.h>
>>> +#include <linux/platform_device.h>
>>> +#include <linux/io.h>
>>> +#include <linux/of.h>
>>> +#include <linux/of_address.h>
>>> +#include <linux/phy/phy.h>
>>> +#include <linux/delay.h>
>>> +#include <linux/regulator/consumer.h>
>>> +#include <linux/extcon.h>
>>> +#include <linux/gpio.h>
>>> +#include <linux/gpio/consumer.h>
>>> +#include <linux/interrupt.h>
>>> +
>>> +#define CDRU_USBPHY_CLK_RST_SEL_OFFSET 0x0
>>> +#define CDRU_USBPHY2_HOST_DEV_SEL_OFFSET 0x4
>>> +#define CDRU_USB_DEV_SUSPEND_RESUME_CTRL_OFFSET 0x5C
>>> +#define CDRU_USBPHY_P0_STATUS_OFFSET 0x1C
>>> +#define CDRU_USBPHY_P1_STATUS_OFFSET 0x34
>>> +#define CDRU_USBPHY_P2_STATUS_OFFSET 0x4C
>>
>> Looks like it has 2 different blocks; CDRU and CMRU. Having a comment for
>> each
>> of the block will help.
>>> +#define CRMU_USB_PHY_AON_CTRL_OFFSET 0x0
>>> +
>>> +#define CDRU_USBPHY_USBPHY_ILDO_ON_FLAG BIT(1)
>>> +#define CDRU_USBPHY_USBPHY_PLL_LOCK BIT(0)
>>> +#define CDRU_USB_DEV_SUSPEND_RESUME_CTRL_DISABLE BIT(0)
>>> +
>>> +#define PHY2_DEV_HOST_CTRL_SEL_DEVICE 0
>>> +#define PHY2_DEV_HOST_CTRL_SEL_HOST 1
>>> +#define PHY2_DEV_HOST_CTRL_SEL_IDLE 2
>>> +#define CRMU_USBPHY_P0_AFE_CORERDY_VDDC BIT(1)
>>> +#define CRMU_USBPHY_P0_RESETB BIT(2)
>>> +#define CRMU_USBPHY_P1_AFE_CORERDY_VDDC BIT(9)
>>> +#define CRMU_USBPHY_P1_RESETB BIT(10)
>>> +#define CRMU_USBPHY_P2_AFE_CORERDY_VDDC BIT(17)
>>> +#define CRMU_USBPHY_P2_RESETB BIT(18)
>>> +
>>> +#define USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET 0x0408
>>> +#define USB2_IDM_IDM_IO_CONTROL_DIRECT_CLK_ENABLE BIT(0)
>>> +#define SUSPEND_OVERRIDE_0 13
>>> +#define SUSPEND_OVERRIDE_1 14
>>> +#define SUSPEND_OVERRIDE_2 15
>>> +#define USB2_IDM_IDM_RESET_CONTROL_OFFSET 0x0800
>>> +#define USB2_IDM_IDM_RESET_CONTROL__RESET 0
>>> +#define USB2D_IDM_IDM_IO_SS_CLEAR_NAK_NEMPTY_EN_I BIT(24)
>>> +
>>> +#define PLL_LOCK_RETRY_COUNT 1000
>>> +#define MAX_REGULATOR_NAME_LEN 25
>>> +#define DUAL_ROLE_PHY 2
>>> +
>>> +#define USBPHY_WQ_DELAY_MS msecs_to_jiffies(500)
>>> +#define USB2_SEL_DEVICE 0
>>> +#define USB2_SEL_HOST 1
>>> +#define USB2_SEL_IDLE 2
>>> +#define USB_CONNECTED 1
>>> +#define USB_DISCONNECTED 0
>>> +#define MAX_NUM_PHYS 3
>>> +
>>> +static const int status_reg[] = {CDRU_USBPHY_P0_STATUS_OFFSET,
>>> + CDRU_USBPHY_P1_STATUS_OFFSET,
>>> + CDRU_USBPHY_P2_STATUS_OFFSET};
>>> +
>>> +struct cygnus_phy_instance;
>>> +
>>> +struct cygnus_phy_driver {
>>> + void __iomem *cdru_usbphy_regs;
>>> + void __iomem *crmu_usbphy_aon_ctrl_regs;
>>> + void __iomem *usb2h_idm_regs;
>>> + void __iomem *usb2d_idm_regs;
>>> + int num_phys;
>>> + bool idm_host_enabled;
>>> + struct cygnus_phy_instance *instances;
>>> + int phyto_src_clk;
>>> + struct platform_device *pdev;
>>> +};
>>> +
>>> +struct cygnus_phy_instance {
>>> + struct cygnus_phy_driver *driver;
>>> + struct phy *generic_phy;
>>> + int port;
>>> + int new_state; /* 1 - Host, 0 - device, 2 - idle*/
>>> + bool power; /* 1 - powered_on 0 - powered off */
>>> + struct regulator *vbus_supply;
>>> + spinlock_t lock;
>>> + struct extcon_dev *edev;
>>> + struct notifier_block device_nb;
>>> + struct notifier_block host_nb;
>>> +};
>>> +
>>> +static const unsigned int usb_extcon_cable[] = {
>>> + EXTCON_USB,
>>> + EXTCON_USB_HOST,
>>> + EXTCON_NONE,
>>> +};
>
> The usb_extcon_cable[] is not used in this driver.
> Please remove it. This array is required on the extcon
> provider driver. But, in this case, it is consumer driver.
Ok, Thanks. I will fix it in the next version of the patch.
>>> +
>>> +static inline int phy_pll_lock_stat(u32 usb_reg, int bit_mask,
>>> + struct cygnus_phy_driver *phy_driver)
>>> +{
>>> + /* Wait for the PLL lock status */
>>> + int retry = PLL_LOCK_RETRY_COUNT;
>>> + u32 reg_val;
>>> +
>>> + do {
>>> + udelay(1);
>>> + reg_val = readl(phy_driver->cdru_usbphy_regs +
>>> + usb_reg);
>>> + if (reg_val & bit_mask)
>>> + return 0;
>>> + } while (--retry > 0);
>>> +
>>> + return -EBUSY;
>>> +}
>>> +
>>> +static struct phy *cygnus_phy_xlate(struct device *dev,
>>> + struct of_phandle_args *args)
>>> +{
>>> + struct cygnus_phy_driver *phy_driver = dev_get_drvdata(dev);
>>> + struct cygnus_phy_instance *instance_ptr;
>>> +
>>> + if (!phy_driver)
>>> + return ERR_PTR(-EINVAL);
>>> +
>>> + if (WARN_ON(args->args[0] >= phy_driver->num_phys))
>>> + return ERR_PTR(-ENODEV);
>>> +
>>> + if (WARN_ON(args->args_count < 1))
>>> + return ERR_PTR(-EINVAL);
>>> +
>>> + instance_ptr = &phy_driver->instances[args->args[0]];
>>
>> if the PHY consumer driver points the PHY sub-node, then of_xlate provided in
>> phy core could be used instead of the custom xlate.
>>> + if (instance_ptr->port > phy_driver->phyto_src_clk)
>>> + phy_driver->phyto_src_clk = instance_ptr->port;
>>> +
>>> + if (instance_ptr->port == DUAL_ROLE_PHY)
>>> + goto ret_p2;
>>> + phy_driver->instances[instance_ptr->port].new_state =
>>> + PHY2_DEV_HOST_CTRL_SEL_HOST;
>>> +
>>> +ret_p2:
>>> + return phy_driver->instances[instance_ptr->port].generic_phy;
>>> +}
>>> +
>>> +static void cygnus_usbp2_dev_clock_init(struct phy *generic_phy, bool
>>> enable)
>>> +{
>>> + u32 reg_val;
>>> + struct cygnus_phy_instance *instance_ptr =
>>> phy_get_drvdata(generic_phy);
>>> + struct cygnus_phy_driver *phy_driver = instance_ptr->driver;
>>> +
>>> + reg_val = readl(phy_driver->usb2d_idm_regs +
>>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>>> +
>>> + if (enable)
>>> + reg_val |= USB2_IDM_IDM_IO_CONTROL_DIRECT_CLK_ENABLE;
>>> + else
>>> + reg_val &= ~USB2_IDM_IDM_IO_CONTROL_DIRECT_CLK_ENABLE;
>>> +
>>> + writel(reg_val, phy_driver->usb2d_idm_regs +
>>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>>> +
>>> + reg_val = readl(phy_driver->usb2d_idm_regs +
>>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>>> +
>>> + if (enable)
>>> + reg_val &= ~BIT(USB2_IDM_IDM_RESET_CONTROL__RESET);
>>> + else
>>> + reg_val |= BIT(USB2_IDM_IDM_RESET_CONTROL__RESET);
>>> +
>>> + writel(reg_val, phy_driver->usb2d_idm_regs +
>>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>>> +}
>>> +
>>> +static void cygnus_phy_clk_reset_src_switch(struct phy *generic_phy,
>>> + u32 src_phy)
>>> +{
>>> + u32 reg_val;
>>> + struct cygnus_phy_instance *instance_ptr =
>>> phy_get_drvdata(generic_phy);
>>> + struct cygnus_phy_driver *phy_driver = instance_ptr->driver;
>>> +
>>> + writel(src_phy, phy_driver->cdru_usbphy_regs +
>>> + CDRU_USBPHY_CLK_RST_SEL_OFFSET);
>>> +
>>> + /* Force the clock/reset source phy to not suspend */
>>> + reg_val = readl(phy_driver->usb2h_idm_regs +
>>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>>> + reg_val &= ~(BIT(SUSPEND_OVERRIDE_0) |
>>> + BIT(SUSPEND_OVERRIDE_1) |
>>> + BIT(SUSPEND_OVERRIDE_2));
>>> + reg_val |= BIT(SUSPEND_OVERRIDE_0 + src_phy);
>>> +
>>> + writel(reg_val, phy_driver->usb2h_idm_regs +
>>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>>> +}
>>> +
>>> +static void cygnus_phy_dual_role_init(struct cygnus_phy_instance
>>> *instance_ptr)
>>> +{
>>> + u32 reg_val;
>>> + struct cygnus_phy_driver *phy_driver = instance_ptr->driver;
>>> +
>>> + if (instance_ptr->new_state == PHY2_DEV_HOST_CTRL_SEL_HOST) {
>>> + writel(PHY2_DEV_HOST_CTRL_SEL_HOST,
>>> + phy_driver->cdru_usbphy_regs +
>>> + CDRU_USBPHY2_HOST_DEV_SEL_OFFSET);
>>
>> If you add a return here, the below block can be placed outside the else
>> block.
>>> + } else {
>>> + /*
>>> + * Disable suspend/resume signals to device controller
>>> + * when a port is in device mode
>>> + */
>>> + writel(PHY2_DEV_HOST_CTRL_SEL_DEVICE,
>>> + phy_driver->cdru_usbphy_regs +
>>> + CDRU_USBPHY2_HOST_DEV_SEL_OFFSET);
>>> + reg_val = readl(phy_driver->cdru_usbphy_regs +
>>> + CDRU_USB_DEV_SUSPEND_RESUME_CTRL_OFFSET);
>>> + reg_val |= CDRU_USB_DEV_SUSPEND_RESUME_CTRL_DISABLE;
>>> + writel(reg_val, phy_driver->cdru_usbphy_regs +
>>> + CDRU_USB_DEV_SUSPEND_RESUME_CTRL_OFFSET);
>>> + }
>>> +}
>>> +
>>> +static int cygnus_phy_init(struct phy *generic_phy)
>>> +{
>>> + struct cygnus_phy_instance *instance_ptr =
>>> phy_get_drvdata(generic_phy);
>>> +
>>> + if (instance_ptr->port == DUAL_ROLE_PHY)
>>> + cygnus_phy_dual_role_init(instance_ptr);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static int cygnus_phy_shutdown(struct phy *generic_phy)
>>> +{
>>> + u32 reg_val;
>>> + int i, ret;
>>> + unsigned long flags;
>>> + bool power_off_flag = true;
>>> + struct cygnus_phy_instance *instance_ptr =
>>> phy_get_drvdata(generic_phy);
>>> + struct cygnus_phy_driver *phy_driver = instance_ptr->driver;
>>> +
>>> + if (instance_ptr->vbus_supply) {
>>
>> phy core supports phy-supply generic property which can be handled by
>> phy-core.
>>> + ret = regulator_disable(instance_ptr->vbus_supply);
>>> + if (ret) {
>>> + dev_err(&generic_phy->dev,
>>> + "Failed to disable regulator\n");
>>> + return ret;
>>> + }
>>> + }
>>> +
>>> + spin_lock_irqsave(&instance_ptr->lock, flags);
>>> +
>>> + /* power down the phy */
>>> + reg_val = readl(phy_driver->crmu_usbphy_aon_ctrl_regs +
>>> + CRMU_USB_PHY_AON_CTRL_OFFSET);
>>> + if (instance_ptr->port == 0) {
>>> + reg_val &= ~CRMU_USBPHY_P0_AFE_CORERDY_VDDC;
>>> + reg_val &= ~CRMU_USBPHY_P0_RESETB;
>>> + } else if (instance_ptr->port == 1) {
>>> + reg_val &= ~CRMU_USBPHY_P1_AFE_CORERDY_VDDC;
>>> + reg_val &= ~CRMU_USBPHY_P1_RESETB;
>>> + } else if (instance_ptr->port == 2) {
>>> + reg_val &= ~CRMU_USBPHY_P2_AFE_CORERDY_VDDC;
>>> + reg_val &= ~CRMU_USBPHY_P2_RESETB;
>>> + }
>>> + writel(reg_val, phy_driver->crmu_usbphy_aon_ctrl_regs +
>>> + CRMU_USB_PHY_AON_CTRL_OFFSET);
>>> +
>>> + instance_ptr->power = false;
>>> +
>>> + /* Determine whether all the phy's are powered off */
>>> + for (i = 0; i < phy_driver->num_phys; i++) {
>>> + if (phy_driver->instances[i].power == true) {
>>> + power_off_flag = false;
>>> + break;
>>> + }
>>> + }
>>> +
>>> + /* Disable clock to USB device and keep the USB device in reset */
>>> + if (instance_ptr->port == DUAL_ROLE_PHY)
>>> + cygnus_usbp2_dev_clock_init(instance_ptr->generic_phy,
>>> + false);
>>> +
>>> + /*
>>> + * Put the host controller into reset state and
>>> + * disable clock if all the phy's are powered off
>>> + */
>>> + if (power_off_flag) {
>>> + reg_val = readl(phy_driver->usb2h_idm_regs +
>>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>>> + reg_val &= ~USB2_IDM_IDM_IO_CONTROL_DIRECT_CLK_ENABLE;
>>> + writel(reg_val, phy_driver->usb2h_idm_regs +
>>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>>> +
>>> + reg_val = readl(phy_driver->usb2h_idm_regs +
>>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>>> + reg_val |= BIT(USB2_IDM_IDM_RESET_CONTROL__RESET);
>>> + writel(reg_val, phy_driver->usb2h_idm_regs +
>>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>>> + phy_driver->idm_host_enabled = false;
>>> + }
>>> + spin_unlock_irqrestore(&instance_ptr->lock, flags);
>>> + return 0;
>>> +}
>>> +
>>> +static int cygnus_phy_poweron(struct phy *generic_phy)
>>> +{
>>> + int ret;
>>> + unsigned long flags;
>>> + u32 reg_val;
>>> + struct cygnus_phy_instance *instance_ptr =
>>> phy_get_drvdata(generic_phy);
>>> + struct cygnus_phy_driver *phy_driver = instance_ptr->driver;
>>> + u32 extcon_event = instance_ptr->new_state;
>>> +
>>> + /*
>>> + * Switch on the regulator only if in HOST mode
>>> + */
>>> + if (instance_ptr->vbus_supply) {
>>> + ret = regulator_enable(instance_ptr->vbus_supply);
>>> + if (ret) {
>>> + dev_err(&generic_phy->dev,
>>> + "Failed to enable regulator\n");
>>> + goto err_shutdown;
>>> + }
>>> + }
>>> +
>>> + spin_lock_irqsave(&instance_ptr->lock, flags);
>>> + /* Bring the AFE block out of reset to start powering up the PHY */
>>> + reg_val = readl(phy_driver->crmu_usbphy_aon_ctrl_regs +
>>> + CRMU_USB_PHY_AON_CTRL_OFFSET);
>>> + if (instance_ptr->port == 0)
>>> + reg_val |= CRMU_USBPHY_P0_AFE_CORERDY_VDDC;
>>> + else if (instance_ptr->port == 1)
>>> + reg_val |= CRMU_USBPHY_P1_AFE_CORERDY_VDDC;
>>> + else if (instance_ptr->port == 2)
>>> + reg_val |= CRMU_USBPHY_P2_AFE_CORERDY_VDDC;
>>> + writel(reg_val, phy_driver->crmu_usbphy_aon_ctrl_regs +
>>> + CRMU_USB_PHY_AON_CTRL_OFFSET);
>>> +
>>> + /* Check for power on and PLL lock */
>>> + ret = phy_pll_lock_stat(status_reg[instance_ptr->port],
>>> + CDRU_USBPHY_USBPHY_ILDO_ON_FLAG, phy_driver);
>>> + if (ret < 0) {
>>> + dev_err(&generic_phy->dev,
>>> + "Timed out waiting for USBPHY_ILDO_ON_FLAG on port %d",
>>> + instance_ptr->port);
>>> + spin_unlock_irqrestore(&instance_ptr->lock, flags);
>>> + goto err_shutdown;
>>> + }
>>> + ret = phy_pll_lock_stat(status_reg[instance_ptr->port],
>>> + CDRU_USBPHY_USBPHY_PLL_LOCK, phy_driver);
>>> + if (ret < 0) {
>>> + dev_err(&generic_phy->dev,
>>> + "Timed out waiting for USBPHY_PLL_LOCK on port %d",
>>> + instance_ptr->port);
>>> + spin_unlock_irqrestore(&instance_ptr->lock, flags);
>>> + goto err_shutdown;
>>> + }
>>> +
>>> + instance_ptr->power = true;
>>> +
>>> + /* Enable clock to USB device and take the USB device out of reset */
>>> + if (instance_ptr->port == DUAL_ROLE_PHY)
>>> + cygnus_usbp2_dev_clock_init(instance_ptr->generic_phy, true);
>>> +
>>> + /* Set clock source provider to be the last powered on phy */
>>> + if (instance_ptr->port == phy_driver->phyto_src_clk)
>>> + cygnus_phy_clk_reset_src_switch(generic_phy,
>>> + instance_ptr->port);
>>> +
>>> + if (phy_driver->idm_host_enabled != true &&
>>> + extcon_event == PHY2_DEV_HOST_CTRL_SEL_HOST) {
>>> + /* Enable clock to USB host and take the host out of reset */
>>> + reg_val = readl(phy_driver->usb2h_idm_regs +
>>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>>> + reg_val |= USB2_IDM_IDM_IO_CONTROL_DIRECT_CLK_ENABLE;
>>> + writel(reg_val, phy_driver->usb2h_idm_regs +
>>> + USB2_IDM_IDM_IO_CONTROL_DIRECT_OFFSET);
>>> +
>>> + reg_val = readl(phy_driver->usb2h_idm_regs +
>>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>>> + reg_val &= ~BIT(USB2_IDM_IDM_RESET_CONTROL__RESET);
>>> + writel(reg_val, phy_driver->usb2h_idm_regs +
>>> + USB2_IDM_IDM_RESET_CONTROL_OFFSET);
>>> + phy_driver->idm_host_enabled = true;
>>> + }
>>> + spin_unlock_irqrestore(&instance_ptr->lock, flags);
>>> +
>>> + return 0;
>>> +err_shutdown:
>>> + cygnus_phy_shutdown(generic_phy);
>>> + return ret;
>>> +}
>>> +
>>> +static int usbd_connect_notify(struct notifier_block *self,
>>> + unsigned long event, void *ptr)
>>> +{
>>> + struct cygnus_phy_instance *instance_ptr = container_of(self,
>>> + struct cygnus_phy_instance, device_nb);
>>> +
>>> + if (event) {
>>> + instance_ptr->new_state = PHY2_DEV_HOST_CTRL_SEL_DEVICE;
>>> + cygnus_phy_dual_role_init(instance_ptr);
>>> + }
>>> +
>>> + return NOTIFY_OK;
>>> +}
>>> +
>>> +static int usbh_connect_notify(struct notifier_block *self,
>>> + unsigned long event, void *ptr)
>>> +{
>>> + struct cygnus_phy_instance *instance_ptr = container_of(self,
>>> + struct cygnus_phy_instance, host_nb);
>>> + if (event) {
>>> + instance_ptr->new_state = PHY2_DEV_HOST_CTRL_SEL_HOST;
>>> + cygnus_phy_dual_role_init(instance_ptr);
>>> + }
>>> +
>>> + return NOTIFY_OK;
>>> +}
>>> +
>>> +static int cygnus_register_extcon_notifiers(
>>> + struct cygnus_phy_instance *instance_ptr)
>>> +{
>>> + int ret = 0;
>>> + struct device *dev = &instance_ptr->generic_phy->dev;
>>> +
>>> + if (of_property_read_bool(dev->of_node, "extcon")) {
>>> + instance_ptr->edev = extcon_get_edev_by_phandle(dev, 0);
>>> + if (IS_ERR(instance_ptr->edev)) {
>>> + if (PTR_ERR(instance_ptr->edev) == -EPROBE_DEFER)
>>> + return -EPROBE_DEFER;
>>> + ret = PTR_ERR(instance_ptr->edev);
>>> + goto err;
>>> + }
>>> +
>>> + instance_ptr->device_nb.notifier_call = usbd_connect_notify;
>>> + ret = extcon_register_notifier(instance_ptr->edev, EXTCON_USB,
>>> + &instance_ptr->device_nb);
>
> You better to use devm_extcon_register_notifier
> because you didn't handle the unregister operation in this patch.
Ok, I will fix it in the next version of the patch.
>>> + if (ret < 0) {
>>> + dev_err(dev, "Can't register extcon device\n");
>
> IMO, "can't register extcon notfiier' is more correct
> instead of 'extcon device' expression.
Ok, I will fix it in the next version of the patch.
>>> + goto err;
>>> + }
>>> +
>>> + if (extcon_get_state(instance_ptr->edev, EXTCON_USB) == true) {
>>> + instance_ptr->new_state =
>>> PHY2_DEV_HOST_CTRL_SEL_DEVICE;
>>> + cygnus_phy_dual_role_init(instance_ptr);
>>> + }
>>> +
>>> + instance_ptr->host_nb.notifier_call = usbh_connect_notify;
>>> + ret = extcon_register_notifier(instance_ptr->edev,
>
> ditto. (devm_extcon_register_notifier)
Ok, I will fix it in the next version of the patch.
>>> + EXTCON_USB_HOST,
>>> + &instance_ptr->host_nb);
>>> + if (ret < 0) {
>>> + dev_err(dev, "Can't register extcon device\n");
>
> ditto.
Ok, I will fix it in the next version of the patch.
>>> + goto err;
>>> + }
>>> +
>>> + if (extcon_get_state(instance_ptr->edev, EXTCON_USB_HOST)
>>> + == true) {
>>> + instance_ptr->new_state = PHY2_DEV_HOST_CTRL_SEL_HOST;
>>> + cygnus_phy_dual_role_init(instance_ptr);
>>> + }
>>> + } else {
>>> + dev_err(dev, "Extcon device handle not found\n");
>>> + return -EINVAL;
>
> I'm not sure about this error. Because it depend on how to
> develope the device driver. Each device driver can decide whether
> the extcon is necessary or optional.
In our case extcon is necessary because all of our SoC's will have
dual role phy.
So decided to return -EINVAL.
>>> + }
>>> +
>>> + return 0;
>>> +err:
>>> + return ret;
>>> +}
>>> +
>>> +static const struct phy_ops ops = {
>>> + .init = cygnus_phy_init,
>>> + .power_on = cygnus_phy_poweron,
>>> + .power_off = cygnus_phy_shutdown,
>>
>> missing .owner
>>> +};
>>> +
>>> +static int cygnus_phy_instance_create(struct cygnus_phy_driver *phy_driver)
>>> +{
>>> + struct device_node *child;
>>> + char *vbus_name;
>>> + struct platform_device *pdev = phy_driver->pdev;
>>> + struct device *dev = &pdev->dev;
>>> + struct device_node *node = dev->of_node;
>>> + struct cygnus_phy_instance *instance_ptr;
>>> + unsigned int id, ret;
>>> +
>>> + for_each_available_child_of_node(node, child) {
>>> + if (of_property_read_u32(child, "reg", &id)) {
>>> + dev_err(dev, "missing reg property for %s\n",
>>> + child->name);
>>> + ret = -EINVAL;
>>> + goto put_child;
>>> + }
>>> +
>>> + if (id >= MAX_NUM_PHYS) {
>>> + dev_err(dev, "invalid PHY id: %u\n", id);
>>> + ret = -EINVAL;
>>> + goto put_child;
>>> + }
>>> +
>>> + instance_ptr = &phy_driver->instances[id];
>>> + instance_ptr->driver = phy_driver;
>>> + instance_ptr->port = id;
>>> + spin_lock_init(&instance_ptr->lock);
>>> +
>>> + if (instance_ptr->generic_phy) {
>>> + dev_err(dev, "duplicated PHY id: %u\n", id);
>>> + ret = -EINVAL;
>>> + goto put_child;
>>> + }
>>> +
>>> + instance_ptr->generic_phy =
>>> + devm_phy_create(dev, child, &ops);
>>> + if (IS_ERR(instance_ptr->generic_phy)) {
>>> + dev_err(dev, "Failed to create usb phy %d", id);
>>> + ret = PTR_ERR(instance_ptr->generic_phy);
>>> + goto put_child;
>>> + }
>>> +
>>> + vbus_name = devm_kzalloc(&instance_ptr->generic_phy->dev,
>>> + MAX_REGULATOR_NAME_LEN,
>>> + GFP_KERNEL);
>>> + if (!vbus_name) {
>>> + ret = -ENOMEM;
>>> + goto put_child;
>>> + }
>>> +
>>> + /* regulator use is optional */
>>> + sprintf(vbus_name, "vbus-p%d", id);
>>> + instance_ptr->vbus_supply =
>>> + devm_regulator_get(&instance_ptr->generic_phy->dev,
>>> + vbus_name);
>>> + if (IS_ERR(instance_ptr->vbus_supply))
>>> + instance_ptr->vbus_supply = NULL;
>>> + devm_kfree(&instance_ptr->generic_phy->dev, vbus_name);
>>> + phy_set_drvdata(instance_ptr->generic_phy, instance_ptr);
>>> + }
>>> +
>>> + return 0;
>>> +
>>> +put_child:
>>> + of_node_put(child);
>>> + return ret;
>>> +}
>>> +
>>> +static int cygnus_phy_probe(struct platform_device *pdev)
>>> +{
>>> + struct resource *res;
>>> + struct cygnus_phy_driver *phy_driver;
>>> + struct phy_provider *phy_provider;
>>> + int i, ret;
>>> + u32 reg_val;
>>> + struct device *dev = &pdev->dev;
>>> + struct device_node *node = dev->of_node;
>>> +
>>> + /* allocate memory for each phy instance */
>>> + phy_driver = devm_kzalloc(dev, sizeof(struct cygnus_phy_driver),
>>> + GFP_KERNEL);
>>> + if (!phy_driver)
>>> + return -ENOMEM;
>>> +
>>> + phy_driver->num_phys = of_get_child_count(node);
>>> +
>>> + if (phy_driver->num_phys == 0) {
>>> + dev_err(dev, "PHY no child node\n");
>>> + return -ENODEV;
>>> + }
>>> +
>>> + phy_driver->instances = devm_kcalloc(dev, phy_driver->num_phys,
>>> + sizeof(struct
>>> cygnus_phy_instance),
>>> + GFP_KERNEL);
>>> + phy_driver->pdev = pdev;
>>> + platform_set_drvdata(pdev, phy_driver);
>>> +
>>> + ret = cygnus_phy_instance_create(phy_driver);
>>> + if (ret)
>>> + return ret;
>>> +
>>> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>>> + "crmu-usbphy-aon-ctrl");
>>> + phy_driver->crmu_usbphy_aon_ctrl_regs = devm_ioremap_resource(dev,
>>> res);
>>> + if (IS_ERR(phy_driver->crmu_usbphy_aon_ctrl_regs))
>>> + return PTR_ERR(phy_driver->crmu_usbphy_aon_ctrl_regs);
>>> +
>>> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
>>> + "cdru-usbphy");
>>> + phy_driver->cdru_usbphy_regs = devm_ioremap_resource(dev, res);
>>> + if (IS_ERR(phy_driver->cdru_usbphy_regs))
>>> + return PTR_ERR(phy_driver->cdru_usbphy_regs);
>>> +
>>> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "usb2h-idm");
>>> + phy_driver->usb2h_idm_regs = devm_ioremap_resource(dev, res);
>>> + if (IS_ERR(phy_driver->usb2h_idm_regs))
>>> + return PTR_ERR(phy_driver->usb2h_idm_regs);
>>> +
>>> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "usb2d-idm");
>>> + phy_driver->usb2d_idm_regs = devm_ioremap_resource(dev, res);
>>> + if (IS_ERR(phy_driver->usb2d_idm_regs))
>>> + return PTR_ERR(phy_driver->usb2d_idm_regs);
>>> +
>>> + reg_val = readl(phy_driver->usb2d_idm_regs);
>>> + writel((reg_val | USB2D_IDM_IDM_IO_SS_CLEAR_NAK_NEMPTY_EN_I),
>>> + phy_driver->usb2d_idm_regs);
>>> + phy_driver->idm_host_enabled = false;
>>> +
>>> + /*
>>> + * Shutdown all ports. They can be powered up as
>>> + * required
>>> + */
>>> + reg_val = readl(phy_driver->crmu_usbphy_aon_ctrl_regs +
>>> + CRMU_USB_PHY_AON_CTRL_OFFSET);
>>> + reg_val &= ~CRMU_USBPHY_P0_AFE_CORERDY_VDDC;
>>> + reg_val &= ~CRMU_USBPHY_P0_RESETB;
>>> + reg_val &= ~CRMU_USBPHY_P1_AFE_CORERDY_VDDC;
>>> + reg_val &= ~CRMU_USBPHY_P1_RESETB;
>>> + reg_val &= ~CRMU_USBPHY_P2_AFE_CORERDY_VDDC;
>>> + reg_val &= ~CRMU_USBPHY_P2_RESETB;
>>> + writel(reg_val, phy_driver->crmu_usbphy_aon_ctrl_regs +
>>> + CRMU_USB_PHY_AON_CTRL_OFFSET);
>>
>> move the above to a separate function to make probe a lot cleaner.
>>
>> Thanks
>> Kishon
>>
>>
>>
>
> --
> Best Regards,
> Chanwoo Choi
> Samsung Electronics
