Hi Tim,
On Thu, Nov 09, 2017 at 10:45:33AM -0800, Tim Harvey wrote:
> Cc: Rob Herring <r...@kernel.org>
> Signed-off-by: Tim Harvey <thar...@gateworks.com>
> ---
> v3:
> - fix typo
>
> v2:
> - add vendor prefix and remove _ from vidout-portcfg
> - remove _ from labels
> - remove max-pixel-rate property
> - describe and provide example for single output port
> - update to new audio port bindings
> ---
> .../devicetree/bindings/media/i2c/tda1997x.txt | 179
> +++++++++++++++++++++
> 1 file changed, 179 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
> b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
> new file mode 100644
> index 0000000..dd37f14
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
> @@ -0,0 +1,179 @@
> +Device-Tree bindings for the NXP TDA1997x HDMI receiver
> +
> +The TDA19971/73 are HDMI video receivers.
> +
> +The TDA19971 Video port output pins can be used as follows:
> + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
> + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
> + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
> + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
> + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0]
> CbCr[11:0]
> + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
> + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
> +
> +The TDA19973 Video port output pins can be used as follows:
> + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
> + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
> + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
> +
> +The Video port output pins are mapped via 4-bit 'pin groups' allowing
> +for a variety of connection possibilities including swapping pin order within
> +pin groups. The video_portcfg device-tree property consists of register
> mapping
> +pairs which map a chip-specific VP output register to a 4-bit pin group. If
> +the pin group needs to be bit-swapped you can use the *_S pin-group defines.
> +
> +Required Properties:
> + - compatible :
> + - "nxp,tda19971" for the TDA19971
> + - "nxp,tda19973" for the TDA19973
> + - reg : I2C slave address
> + - interrupts : The interrupt number
> + - DOVDD-supply : Digital I/O supply
> + - DVDD-supply : Digital Core supply
> + - AVDD-supply : Analog supply
> + - nxp,vidout-portcfg : array of pairs mapping VP output pins to pin groups.
> +
> +Optional Properties:
> + - nxp,audout-format : DAI bus format: "i2s" or "spdif".
> + - nxp,audout-width : width of audio output data bus (1-4).
> + - nxp,audout-layout : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used).
> + - nxp,audout-mclk-fs : Multiplication factor between stream rate and codec
> + mclk.
> +
> +The device node must contain one 'port' child node for its digital output
> +video port, in accordance with the video interface bindings defined in
> +Documentation/devicetree/bindings/media/video-interfaces.txt.
Could you add that this port has one endpoint node as well? (Unless you
support multiple, that is.)
> +
> +Optional Endpoint Properties:
> + The following three properties are defined in video-interfaces.txt and
> + are valid for source endpoints only:
Transmitters? Don't you have an endpoint only in the port representing the
transmitter?
> + - hsync-active: Horizontal synchronization polarity. Defaults to active
> high.
> + - vsync-active: Vertical synchronization polarity. Defaults to active high.
> + - data-active: Data polarity. Defaults to active high.
> +
> +Examples:
> + - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422
> + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
> + hdmi-receiver@48 {
> + compatible = "nxp,tda19971";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tda1997x>;
> + reg = <0x48>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> + DOVDD-supply = <®_3p3v>;
> + AVDD-supply = <®_1p8v>;
> + DVDD-supply = <®_1p8v>;
> + /* audio */
> + #sound-dai-cells = <0>;
> + nxp,audout-format = "i2s";
> + nxp,audout-layout = <0>;
> + nxp,audout-width = <16>;
> + nxp,audout-mclk-fs = <128>;
> + /*
> + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
> + * and Y[11:4] across 16bits in the same pixclk cycle.
> + */
> + nxp,vidout-portcfg =
> + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
> + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
> + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
> + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
> + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
> + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
> + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
> + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
> +
> + port {
> + tda1997x_to_ipu1_csi0_mux: endpoint {
> + remote-endpoint =
> <&ipu1_csi0_mux_from_parallel_sensor>;
> + bus-width = <16>;
> + hsync-active = <1>;
> + vsync-active = <1>;
> + data-active = <1>;
> + };
> + };
> + };
> + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
> + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
> + hdmi-receiver@48 {
> + compatible = "nxp,tda19971";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tda1997x>;
> + reg = <0x48>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> + DOVDD-supply = <®_3p3v>;
> + AVDD-supply = <®_1p8v>;
> + DVDD-supply = <®_1p8v>;
> + /* audio */
> + #sound-dai-cells = <0>;
> + nxp,audout-format = "i2s";
> + nxp,audout-layout = <0>;
> + nxp,audout-width = <16>;
> + nxp,audout-mclk-fs = <128>;
> + /*
> + * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
> + * and Y[11:4] across 16bits in the same pixclk cycle.
> + */
> + nxp,vidout-portcfg =
> + /* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
> + < TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
> + /* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
> + < TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
> + /* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
> + < TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
> + /* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
> + < TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
> +
> + port {
> + tda1997x_to_ipu1_csi0_mux: endpoint {
> + remote-endpoint =
> <&ipu1_csi0_mux_from_parallel_sensor>;
> + bus-width = <16>;
> + hsync-active = <1>;
> + vsync-active = <1>;
> + data-active = <1>;
> + };
> + };
> + };
> + - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
> + 16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
> + hdmi-receiver@48 {
> + compatible = "nxp,tda19971";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_tda1997x>;
> + reg = <0x48>;
> + interrupt-parent = <&gpio1>;
> + interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
> + DOVDD-supply = <®_3p3v>;
> + AVDD-supply = <®_1p8v>;
> + DVDD-supply = <®_1p8v>;
> + /* audio */
> + #sound-dai-cells = <0>;
> + nxp,audout-format = "i2s";
> + nxp,audout-layout = <0>;
> + nxp,audout-width = <16>;
> + nxp,audout-mclk-fs = <128>;
> + /*
> + * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over
> + * 2 pixclk cycles.
> + */
> + nxp,vidout-portcfg =
> + /* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
> + < TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >,
> + /* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
> + < TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >,
> +
> + port {
> + tda1997x_to_ipu1_csi0_mux: endpoint {
> + remote-endpoint =
> <&ipu1_csi0_mux_from_parallel_sensor>;
> + bus-width = <16>;
> + hsync-active = <1>;
> + vsync-active = <1>;
> + data-active = <1>;
> + };
> + };
> + };
> +
> --
> 2.7.4
>
--
Sakari Ailus
e-mail: sakari.ai...@iki.fi
