For Micron spi nor device, when erase/program operation fails, especially the failure results from intending to modify protected space, spi-nor upper layers still get the return which shows the operation succeeds. This is because current spi_nor_fsr_ready() only uses FSR bit.7 (flag status register) to check device whether ready. This patch fixs this issue by checking relevant error bits in FSR. The FSR is a powerful tool to investigate the staus of device, checking information regarding what is actually doing the memory and detecting possible error conditions.
Signed-off-by: beanhuo <[email protected]> --- v1 - v2: - Changed some error comments based on Cyrille's reviews. drivers/mtd/spi-nor/spi-nor.c | 18 ++++++++++++++++-- include/linux/mtd/spi-nor.h | 6 +++++- 2 files changed, 21 insertions(+), 3 deletions(-) diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c index 19c00072..4423605 100644 --- a/drivers/mtd/spi-nor/spi-nor.c +++ b/drivers/mtd/spi-nor/spi-nor.c @@ -328,8 +328,22 @@ static inline int spi_nor_fsr_ready(struct spi_nor *nor) int fsr = read_fsr(nor); if (fsr < 0) return fsr; - else - return fsr & FSR_READY; + + if (fsr & (FSR_E_ERR | FSR_P_ERR)) { + if (fsr & FSR_E_ERR) + dev_err(nor->dev, "Erase operation failed.\n"); + else + dev_err(nor->dev, "Program operation failed.\n"); + + if (fsr & FSR_PT_ERR) + dev_err(nor->dev, + "Attempted to modify a protected sector.\n"); + + nor->write_reg(nor, SPINOR_OP_CLFSR, NULL, 0); + return -EIO; + } + + return fsr & FSR_READY; } static int spi_nor_ready(struct spi_nor *nor) diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h index 1f0a7fc..da8e0d5 100644 --- a/include/linux/mtd/spi-nor.h +++ b/include/linux/mtd/spi-nor.h @@ -61,6 +61,7 @@ #define SPINOR_OP_RDSFDP 0x5a /* Read SFDP */ #define SPINOR_OP_RDCR 0x35 /* Read configuration register */ #define SPINOR_OP_RDFSR 0x70 /* Read flag status register */ +#define SPINOR_OP_CLFSR 0x50 /* Clear flag status register */ /* 4-byte address opcodes - used on Spansion and some Macronix flashes. */ #define SPINOR_OP_READ_4B 0x13 /* Read data bytes (low frequency) */ @@ -130,7 +131,10 @@ #define EVCR_QUAD_EN_MICRON BIT(7) /* Micron Quad I/O */ /* Flag Status Register bits */ -#define FSR_READY BIT(7) +#define FSR_READY BIT(7) /* Device status, 0 = Busy, 1 = Ready */ +#define FSR_E_ERR BIT(5) /* Erase operation status */ +#define FSR_P_ERR BIT(4) /* Program operation status */ +#define FSR_PT_ERR BIT(1) /* Protection error bit */ /* Configuration Register bits. */ #define CR_QUAD_EN_SPAN BIT(1) /* Spansion Quad I/O */ -- 2.7.4
